The condition (reg_val != 2) || (reg_val != 3) will always be true because
reg_val cannot be equal to two different values at the same time. Fix this
by replacing the || operator with && so that the loop will loop if reg_val
is not a 2 and not a 3 as was originally intended.
Fixes: 50dc2f221455 ("scsi: pm80xx: Modified the logic to collect fatal dump")
Link: https://lore.kernel.org/r/20191120135031.270708-1-colin.king@canonical.com
Addresses-Coverity: ("Constant expression result")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The commands to the controller are sent in fixed sized chunks which are set
per-chip-generation and stashed in iomb_size. The driver fills in structs
matching the register layout and memcpy this to memory shared with the
controller. However, there are two problem cases:
1) Things like phy_start_req are too large because they share the
sas_identify_frame definition with libsas, and it includes the crc
word. This means that it's overwriting the start of the next
command block, that's ok except if it happens at the end of the
shared memory area.
2) Things like set_nvm_data_req which are shared between the HAL
layers. This means that it's sending 'random' data for things that
are in the reserved area. So far we haven't found a case where the
controller FW cares, but sending possible gibberish (for most of
the structures this is in the reserved area so previously zeroed)
is not recommended.
Link: https://lore.kernel.org/r/20191114100910.6153-9-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Disabling the SATA drive interface cause kernel panic. When the drive
Interface is disabled, device should be deregistered after aborting all
pending I/Os. Also changed the port recovery timeout to 10000 ms for
PM8006 controller.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many times in libsas, and in LLDDs which use libsas, the check for an
expander device is re-implemented or open coded.
Use dev_is_expander() instead. We rename this from
sas_dev_type_is_expander() to not spill so many lines in referencing.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename the functions pm8001_chip_is_our_interupt,
pm80xx_chip_is_our_interupt and function pointer is_our_interrupt to fix
spelling mistakes.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When macro PM8001_USE_MSIX is defined there are redundant dead code calls
to pm8001_chip_intx_interrupt_{enable|disable} and pm8001_cr32.
Clean this up for the defined PM8001_USE_MSIX and undefined
PM8001_USE_MSIX cases.
[mkp: squashed two patches]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/pm8001/pm80xx_hwi.c: In function 'pm8001_set_phy_profile':
drivers/scsi/pm8001/pm80xx_hwi.c:4679:6: warning:
variable 'page_code' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the firmware is not responding, execution of kexec boot causes a system
hang. When firmware assertion happened, driver get notified with interrupt
vector updated in MPI configuration table. Then, the driver will read
scratchpad register and set controller_fatal_error flag to true.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
when there's an error in 'ncq mode' the host has to read the ncq error
log (10h) to clear the error state. however, the ccb that is setup for
doing this doesn't setup the ccb so that the previous state is
cleared. if the ccb was previously used for an IO n_elems is set and
pm8001_ccb_task_free() treats this as the signal to go free a
scatter-gather list (that's already been freed).
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modified SATA abort handling with following steps:
1) Set device state as recovery.
2) Send phy reset.
3) Wait for reset completion.
4) After successful reset, abort all IO's to the device.
5) After aborting all IO's to device, set device state as operational.
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ATTO adapters do not support this feature. If the firmware fails to be
ready, it should not check the examined registers in order to examine
the state of the feature in order to prevent undefined behavior.
Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
PHY profiles are not saved in NVRAM on ATTO 12Gb SAS controllers.
Therefore, in order for the controller to function in a wide range of
configurations, the PHY profiles must be statically set. This patch
provides the necessary functionality to do so.
Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In case psataPayload->status has a status of IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY
ts->stat gets set to SAS_OPEN_REJECT but a missing 'break' statement causes a
fallthrough to the default handler of the switch statement overriding ts->stat
to SAS_DEV_NO_RESPONSE.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
PORT RECOVERY TIMEOUT is the maximum time between the controller's
detection of the PHY down until the receipt of the ID_Frame (from the
same remote SAS port). If the time expires before the ID_FRAME is
received, the port is considered INVALID and can be removed. The
IOP_EVENT_PORT_RECOVERY_TIMER_TMO event is reported following the
IOP_EVENT_ PHY_DOWN event when the PHY/port does not recover after
Port Recovery Time.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Use the ata device class from libata in libsas instead of checking
the supported command set and switch to using ata_dev_classify()
instead of our own method.
Cc: Tejun Heo <tj@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
There is a risk that the variable will be used without being initialized.
This was largely found by using a static code analysis program called cppche
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The driver ignores the return value in a lot of places, fix
it at least somewhere (and release the resources in such cases),
to avoid that bad things happen.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
spin_lock_irqsave for the HBA lock is called in one function where flag
is local to that function. Another function is called from the first
function where lock has to be released using spin_unlock_irqrestore for
calling task_done of libsas. In the second function also flag is declared
and used. For calling task_done there is no need to enable the irq. So
instead of using spin_lock_irqsave and spin_unlock_irqrestore, spin_lock
and spin_unlock is used now. This also avoids passing the flags across all
the functions where HBA lock is being used. Also removed redundant code.
Reported-by: Jason Seba <jason.seba42@gmail.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Signed-off-by: Viswas G <viswas.g@pmcs.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Supports below logging facilities,
Inbound outbound queues dump.
Non fatal dump in case of IO failures.
Fatal dump in case of firmware failure.
[jejb: checkpatch spacing fixes]
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The IO command size is 128 bytes for these new controllers as opposed to 64
for the old 8001 controller.
The Adaptec out-of-tree driver did this correctly. After comparing the two
this turned out to be the crucial difference.
So don't hardcode the IO command size, instead use pm8001_ha->iomb_size as
that is the correct value for both old and new controllers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Anand Kumar Santhanam <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Cc: stable@vger.kernel.org # for v3.10 and up
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull first round of SCSI updates from James Bottomley:
"The patch set is mostly driver updates (usf, zfcp, lpfc, mpt2sas,
megaraid_sas, bfa, ipr) and a few bug fixes. Also of note is that the
Buslogic driver has been rewritten to a better coding style and 64 bit
support added. We also removed the libsas limitation on 16 bytes for
the command size (currently no drivers make use of this)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (101 commits)
[SCSI] megaraid: minor cut and paste error fixed.
[SCSI] ufshcd-pltfrm: remove unnecessary dma_set_coherent_mask() call
[SCSI] ufs: fix register address in UIC error interrupt handling
[SCSI] ufshcd-pltfrm: add missing empty slot in ufs_of_match[]
[SCSI] ufs: use devres functions for ufshcd
[SCSI] ufs: Fix the response UPIU length setting
[SCSI] ufs: rework link start-up process
[SCSI] ufs: remove version check before IS reg clear
[SCSI] ufs: amend interrupt configuration
[SCSI] ufs: wrap the i/o access operations
[SCSI] storvsc: Update the storage protocol to win8 level
[SCSI] storvsc: Increase the value of scsi timeout for storvsc devices
[SCSI] MAINTAINERS: Add myself as the maintainer for BusLogic SCSI driver
[SCSI] BusLogic: Port driver to 64-bit.
[SCSI] BusLogic: Fix style issues
[SCSI] libiscsi: Added new boot entries in the session sysfs
[SCSI] aacraid: Fix for arrays are going offline in the system. System hangs
[SCSI] ipr: IOA Status Code(IOASC) update
[SCSI] sd: Update WRITE SAME heuristics
[SCSI] fnic: potential dead lock in fnic_is_abts_pending()
...
Remove the arbitrary expectation in libsas that all SCSI commands are 16 bytes
or less. Instead do all copies via cmd->cmd_len (and use a pointer to this in
the libsas task instead of a copy). Note that this still doesn't enable > 16
byte CDB support in the underlying drivers because their internal format has
to be fixed and the wire format of > 16 byte CDBs according to the SAS spec is
different. the libsas drivers (isci, aic94xx, mvsas and pm8xxx are all
updated for this change.
Cc: Lukasz Dorau <lukasz.dorau@intel.com>
Cc: Maciej Patelczyk <maciej.patelczyk@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Jack Wang <xjtuwjp@gmail.com>
Cc: Lindar Liu <lindar_liu@usish.com>
Cc: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
