The new device generation has a slightly different suspend resume flow
Currently, the way the driver instruct the device to move to D3 is by
sending D3_CONFIG_CMD.
Instead of using the host command the indication is by writing to the
doorbell interrupt.
The FW will respond with interrupt to indicate transition completion.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Stop accessing the trans configuration via the iwl_cfg structure and
always access it via the iwl_trans structure. This completes the
requirements to disassociate the trans-specific configuration from the
rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a pointer to the iwl_trans structure and point it to the trans
part of the cfg. This is the first step in disassociating the trans
configuration from the rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of accessing the iwl_config_trans_params from the cfg that is
stored in the trans struct, pass this structure directly to functions
that need it during trans_alloc. This will be useful to isolate the
elements needed during allocation and pass them separately before the
actual cfg struct is known.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of setting the cfg to iwl_trans already during allocation, set
it only later when we have had the time to decide which cfg to use.
This is part of the effort to be able to decide the cfg based on HW
revision and RF ID after iwl_trans_alloc() has been called.
For now, since we still have a bunch of code checking the HW revision
and the RF ID, we set iwl_trans->cfg early, even before we decided the
real cfg to use. We only use the trans configuration at this point,
so this is fine for now. In the future, the trans configuration will
be completely independent from the rest of the config structure, so
we'll be able to avoid this.
Additionally, we can't access the PRPH registers in iwl_trans_alloc()
anymore, so move the HW REV C-step check for family 8000 code later to
the probe function as well. This step is probably not necessary, but
if that's the case it should be removed separately later on.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There were a couple of special handling to find the correct cfg inside
iwl_trans_pcie_alloc(). Move them to iwl_pci_probe() so they're
together with the rest of the decisions.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of using iwl_trans->cfg in iwl_trans_pcie_alloc(), use the
local argument that we received. This will allow us to not to set the
cfg during iwl_trans_alloc() so it can be decided later.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to be able to select the cfg depending on the HW revision or
on the RF ID, we need to set up the trans before selecting the cfg.
To do so, move the elements from cfg that are needed by
iwl_trans_alloc() to a separate struct at the top of the cfg, so it
can be used by other cfg types as well, before selecting the rest of
the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Align wrt log prints to the driver coding style
Remove the ext field from the log and print it at the beginning of the
apply point.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
use iwl_trans_dbg_ini_valid function instead of a boolean value check if
dbg_ini mode is on. It is needed for a future patch.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
dma_alloc_coherent is not just the page allocator. The only valid
arguments to pass are either GFP_ATOMIC or GFP_ATOMIC with possible
modifiers of __GFP_NORETRY or __GFP_NOWARN.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This means:
1) stop calling pm_runtime_resume when starting the hardware
2) removing the unneeded low_power parameter to start / stop hw / fw
transport ops
3) squashing transport functions that are now the same
_iwl_trans_pcie_start_hw / iwl_trans_pcie_start_hw
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During D3 state, FW may send packets.
As a result, "write" queue pointer will be incremented by FW.
Upon resume from D3, driver should adjust its shadows of "write" and "read"
pointers to the value reported by FW.
1. Keep TID used during wowlan configuration.
2. Upon resume, set driver's "write" and "read" queue pointers
to the value reported by FW.
Signed-off-by: Alex Malamud <alex.malamud@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This flag should never be set unless integration work with the
platform is done. We don't support any platforms officially and don't
plan to do so in the near future, so we can remove this option
entirely in order to avoid having it enabled by mistake.
This has been marked with "depends on EXPERT", so there shouldn't be
many systems running with it set. And, if there are systems, they
should not be using this flag.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The op mode should stop the debug recording and not the transport layer.
Rename iwl_fwrt_stop_device into iwl_fw_dbg_stop_sync and move the debug
stop recording to it.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We need to use a different firmware for C0 versions of killer Qu NICs.
Add structures for them and handle them in the if block that detects
C0 revisions.
Additionally, instead of having an inclusive check for QnJ devices,
make the selection exclusive, so that switching to QnJ is the
exception, not the default. This prevents us from having to add all
the non-QnJ cards to an exclusion list. To do so, only go into the
QnJ block if the device has an RF ID type HR and HW revision QnJ.
Cc: stable@vger.kernel.org # 5.2
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190821171732.2266-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the HW revision of Qu devices we found is QuZ, then we need to
switch the configuration accordingly in order to use the correct FW.
Add a block of ifs in order do that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We have a too generic condition that switches from Qu configurations
to QnJ configurations. We need to exclude some configurations so that
they are not erroneously switched. Add the ax201 configuration to the
list of exclusions.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to remember how to unmap a memory (as single or
as page), we maintain a bit per Transmit Buffer (TBs) in
the meta data (structure iwl_cmd_meta).
We maintain a bitmap: 1 bit per TB.
If the TB is set, we will free the memory as a page.
This bitmap was never cleared. Fix this.
Cc: stable@vger.kernel.org
Fixes: 3cd1980b0c ("iwlwifi: pcie: introduce new tfd and tb formats")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for C-step devices. Currently we don't have a nice way of
matching the step and choosing the proper configuration, so we need to
switch the config structs one by one.
Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes the register status can include interrupts that
were masked. We can, for example, get the RF-Kill bit set
in the interrupt status register although this interrupt
was masked. Then if we get the ALIVE interrupt (for example)
that was not masked, we need to *not* service the RF-Kill
interrupt.
Fix this in the MSI-X interrupt handler.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newest devices have a new firmware load mechanism. This
mechanism is called the context info. It means that the
driver doesn't need to load the sections of the firmware.
The driver rather prepares a place in DRAM, with pointers
to the relevant sections of the firmware, and the firmware
loads itself.
At the end of the process, the firmware sends the ALIVE
interrupt. This is different from the previous scheme in
which the driver expected the FH_TX interrupt after each
section being transferred over the DMA.
In order to support this new flow, we enabled all the
interrupts. This broke the assumption that we have in the
code that the RF-Kill interrupt can't interrupt the firmware
load flow.
Change the context info flow to enable only the ALIVE
interrupt, and re-enable all the other interrupts only
after the firmware is alive. Then, we won't see the RF-Kill
interrupt until then. Getting the RF-Kill interrupt while
loading the firmware made us kill the firmware while it is
loading and we ended up dumping garbage instead of the firmware
state.
Re-enable the ALIVE | RX interrupts from the ISR when we
get the ALIVE interrupt to be able to get the RX interrupt
that comes immediately afterwards for the ALIVE
notification. This is needed for non MSI-X only.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We added code to restock the buffer upon ALIVE interrupt
when MSI-X is disabled. This was added as part of the context
info code. This code was added only if the ISR debug level
is set which is very unlikely to be related.
Move this code to run even when the ISR debug level is not
set.
Note that gen2 devices work with MSI-X in most cases so that
this path is seldom used.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The 0xF6 command used to start and stop the recording from 22560 devices
was removed. This is causing an assert when the driver tries to alter
the recording state.
Remove the use of the command.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Unite iwl_trans debug related fields under iwl_trans_debug struct to
increase readability and keep iwl_trans clean.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are several flows where the driver checks if it runs in ini mode.
Some of these flows are no longer used in ini mode or there is another
condition that check the ini mode in the same flow. Either way, those
conditions are redundant. Remove the redundant conditions.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we dump only the first 64 bytes of the PCI config space,
which leaves out some important things, such as the base address
registers.
Increase it to 352 for the PCI device and to 524 for the rootport to
make sure we include everything we need.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Improve the robustness of the dump collection flow in case of an early
error:
1. in iwl_trans_pcie_sync_nmi, disable and enable interrupts only if
they were already enabled
2. attempt to initiate dump collection in iwl_fw_dbg_error_collect only
if the device is enabled
3. check Tx command queue was already allocated before trying to collect it
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The 22000 series FW that was meant to be used with hr is
also the FW that is used for hr1 and has a different RF ID.
Add support to load the hr FW when hr1 RF ID is detected.
Cc: stable@vger.kernel.org # 5.1+
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Read fseq info from FW registers and print it upon fw assert.
The print is needed since the fseq version coming from the TLV might
not be the actual version that is used.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver attempts to clear persistence bit on any device familiy even
though only 9000 and 22000 families require it. Clear the bit only on
the relevant device families.
Each HW has different address to the write protection register. Use the
right register for each HW
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 8954e1eb22 ("iwlwifi: trans: Clear persistence bit when starting the FW")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we have a single image (same firmware image for INIT and
OPERATIONAL), we couldn't load the driver and register to the
stack if we had hardware RF-Kill asserted.
Fix this. This required a few changes:
1) Run the firmware as part of the INIT phase even if its
ucode_type is not IWL_UCODE_INIT.
2) Send the commands that are sent to the unified image in
INIT flow even in RF-Kill.
3) Don't ask the transport to stop the hardware upon RF-Kill
interrupt if the RF-Kill is asserted.
4) Allow the RF-Kill interrupt to take us out of L1A so that
the RF-Kill interrupt will be received by the host (to
enable the radio).
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
Kalle Valo says:
====================
wireless-drivers-next patches for 5.2
Most likely the last patchset of new feature for 5.2, and this time we
have quite a lot of new features. Most obvious being rtw88 from
Realtek which supports RTL8822BE and RTL8822CE 802.11ac devices. We
have also new hardware support for existing drivers and improvements.
There's one conflict in iwlwifi, my example conflict resolution below.
Major changes:
iwlwifi
* bump the 20000-series FW API version
* work on new hardware continues
* RTT confidence indication support for Fine Timing Measurement (FTM)
* an improvement in HE (802.11ax) rate-scaling
* add command version parsing from the fimware TLVs
* add support for a new WoWLAN patterns firmware API
rsi
* add support for rs9116
mwifiex
* add support for SD8987
brcmfmac
* add quirk for ACEPC T8 and T11 mini PCs
rt2x00
* add RT3883 support
qtnfmac
* fix debugfs interface to support multiple cards
rtw88
* new driver
mt76
* share more code across drivers
* add support for MT7615 chipset
* rework DMA API
* tx/rx performance optimizations
* use NAPI for tx cleanup on mt76x02
* AP mode support for USB devices
* USB stability fixes
* tx power handling fixes for 76x2
* endian fixes
Conflicts:
There's a trivial conflict in
drivers/net/wireless/intel/iwlwifi/fw/file.h, just leave
IWL_UCODE_TLV_FW_FSEQ_VERSION to the file. 'git diff' output should be
just empty:
diff --cc drivers/net/wireless/intel/iwlwifi/fw/file.h
index cd622af90077,b0671e16e1ce..000000000000
--- a/drivers/net/wireless/intel/iwlwifi/fw/file.h
+++ b/drivers/net/wireless/intel/iwlwifi/fw/file.h
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a solitary and inconspicous ` in the middle of a comment in
this function, which should not be there. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
