Allow the xilinx-pcie driver to be built on MIPS platforms which make use
of generic PCI drivers rather than legacy MIPS-specific interfaces. This
is used on the MIPS Boston development board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharatku@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Ravikiran Gummaluri <rgummal@xilinx.com>
The Xilinx AXI bridge for PCI Express device provides interrupts indicating
the completion of config space accesses. We have previously
enabled/unmasked them but do nothing with them besides acknowledge them.
Leave the interrupts masked in order to avoid servicing a large number of
pointless interrupts during boot.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharatku@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Ravikiran Gummaluri <rgummal@xilinx.com>
The INTx & MSI interrupt decode paths duplicated a fair bit of common
functionality. They also strictly handled interrupts in order of INTx then
MSI, so if both types of interrupt were to be asserted simultaneously and
the MSI interrupt were first in the FIFO then the INTx code would read it &
ignore it before the MSI code then had to read it again, wasting the
original FIFO read.
Unify the INTx & MSI decode in order to reduce that duplication & allow a
single FIFO read to be performed for each interrupt regardless of its type.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharatku@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Ravikiran Gummaluri <rgummal@xilinx.com>
The devicetree binding documentation for the Xilinx NWL PCIe root port
bridge shows an example which uses an interrupt-map property to map PCI
INTx interrupts to hardware IRQ numbers 1-4. The driver creates an IRQ
domain with size 4, which therefore covers the hwirq range 0-3.
This means that if we attempt to make use of the INTD interrupt then we're
likely to hit a WARN() in irq_domain_associate() because INTD, or hwirw=4,
is outside of the range covered by the IRQ domain. irq_domain_associate()
will then return -EINVAL and we'll be unable to make use of INTD.
Fix this by making use of the pci_irqd_intx_xlate() helper function to
translate the 1-4 range used in the DT to a 0-3 range used within the
driver, and stop adding 1 to decoded hwirq numbers.
Whilst cleaning up INTx handling we make use of the new PCI_NUM_INTX macro
& drop the custom INTX definitions.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
The pcie-xilinx driver creates an IRQ domain of size 4 for legacy PCI INTx
interrupts, which at first glance seems reasonable since there are 4
possible such interrupts. Unfortunately the driver then proceeds to use the
range 1-4 as the hwirq numbers for INTA-INTD, causing warnings & broken
interrupts when attempting to use INTD/hwirq=4 due to it being beyond the
range of the IRQ domain:
WARNING: CPU: 0 PID: 1 at kernel/irq/irqdomain.c:365
irq_domain_associate+0x170/0x220
error: hwirq 0x4 is too large for dummy
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W
4.12.0-rc5-00126-g19e1b3a10aad-dirty #427
Stack : 0000000000000000 0000000000000004 0000000000000006 ffffffff8092c78a
0000000000000061 ffffffff8018bf60 0000000000000000 0000000000000000
ffffffff8088c287 ffffffff80811d18 a8000000ffc60000 ffffffff80926678
0000000000000001 0000000000000000 ffffffff80887880 ffffffff80960000
ffffffff80920000 ffffffff801e6744 ffffffff80887880 a8000000ffc4f8f8
000000000000089c ffffffff8018d260 0000000000010000 ffffffff80811d18
0000000000000000 0000000000000001 0000000000000000 0000000000000000
0000000000000000 a8000000ffc4f840 0000000000000000 ffffffff8042cf34
0000000000000000 0000000000000000 0000000000000000 0000000000040c00
0000000000000000 ffffffff8010d1c8 0000000000000000 ffffffff8042cf34
...
Call Trace:
[<ffffffff8010d1c8>] show_stack+0x80/0xa0
[<ffffffff8042cf34>] dump_stack+0xd4/0x110
[<ffffffff8013ea98>] __warn+0xf0/0x108
[<ffffffff8013eb14>] warn_slowpath_fmt+0x3c/0x48
[<ffffffff80196528>] irq_domain_associate+0x170/0x220
[<ffffffff80196bf0>] irq_create_mapping+0x88/0x118
[<ffffffff801976a8>] irq_create_fwspec_mapping+0xb8/0x320
[<ffffffff80197970>] irq_create_of_mapping+0x60/0x70
[<ffffffff805d1318>] of_irq_parse_and_map_pci+0x20/0x38
[<ffffffff8049c210>] pci_fixup_irqs+0x60/0xe0
[<ffffffff8049cd64>] xilinx_pcie_probe+0x28c/0x478
[<ffffffff804e8ca8>] platform_drv_probe+0x50/0xd0
[<ffffffff804e73a4>] driver_probe_device+0x2c4/0x3a0
[<ffffffff804e7544>] __driver_attach+0xc4/0xd0
[<ffffffff804e5254>] bus_for_each_dev+0x64/0xa8
[<ffffffff804e5e40>] bus_add_driver+0x1f0/0x268
[<ffffffff804e8000>] driver_register+0x68/0x118
[<ffffffff801001a4>] do_one_initcall+0x4c/0x178
[<ffffffff808d3ca8>] kernel_init_freeable+0x204/0x2b0
[<ffffffff80730b68>] kernel_init+0x10/0xf8
[<ffffffff80106218>] ret_from_kernel_thread+0x14/0x1c
Fix this by making use of the new pci_irqd_intx_xlate() helper to translate
the INTx 1-4 range into the 0-3 range suitable for the IRQ domain of size
4, and stop adding 1 to the hwirq number decoded from the interrupt FIFO
which is already in the range 0-3.
Whilst we're here we switch to using PCI_NUM_INTX rather than the magic
number 4, making it clearer what the 4 means.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharatku@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Ravikiran Gummaluri <rgummal@xilinx.com>
Use the PCI_NUM_INTX macro to indicate the number of PCI INTx interrupts
rather than the magic number 4. This makes it clearer where the number
comes from & what it relates to.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
of_irq_get() may return a negative error number as well as 0 on failure,
while the driver only checks for 0, blithely continuing with the call to
irq_set_chained_handler_and_data() -- that function expects *unsigned int*
so should probably do nothing when a large IRQ number resulting from a
conversion of a negative error number is passed to it. The driver then
probes successfully while being only partly functional...
Check for 'irq <= 0' instead and propagate the negative error number to the
probe method -- that will allow the deferred probing as well.
Fixes: d3c68e0a7e ("PCI: faraday: Add Faraday Technology FTPCI100 PCI Host Bridge driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The devicetree binding documentation for the Altera PCIe controller shows
an example which uses an interrupt-map property to map PCI INTx interrupts
to hardware IRQ numbers 1-4. The driver creates an IRQ domain with size 5
in order to cover this range, with hwirq=0 left unused.
This patch cleans up this wasted IRQ domain entry, modifying the driver to
use an IRQ domain of size 4 which matches the actual number of PCI INTx
interrupts. Since the hwirq numbers 1-4 are part of the devicetree binding,
and this is considered ABI, we cannot simply change the interrupt-map
property to use the range 0-3. Instead we make use of the
pci_irqd_intx_xlate() helper function to translate the range 1-4 used at
the DT level into the range 0-3 which is now used within the driver, and
stop adding 1 to decoded hwirq numbers in altera_pcie_isr().
Whilst cleaning up INTx handling we make use of the new PCI_NUM_INTX macro
& drop the custom INTX_NUM definition.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ley Foon Tan <lftan@altera.com>
Commit 90634e8540 ("PCI: rcar: Convert PCI scan API to
pci_scan_root_bus_bridge()") converted PCI root bus scan API to the new
pci_scan_root_bus_bridge() API; in the process some error paths were not
updated correctly which may cause memory leaks.
Fix the driver error exit path reinstating the previous correct
error exit behaviour.
Fixes: 90634e8540 ("PCI: rcar: Convert PCI scan API to pci_scan_root_bus_bridge()")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Harunobu Kurokawa <harunobu.kurokawa.dn@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Free up the IRQs we request on the suspend path and reallocate them on the
resume path.
Fixes this error:
CPU 111 disable failed: CPU has 9 vectors assigned and there are only 0 available.
Error taking CPU111 down: -34
Non-boot CPUs are not disabled
Enabling non-boot CPUs ...
Signed-off-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Keith Busch <keith.busch@intel.com>
The setup of MSI with Hyper-V host was sleeping with locks held. This
error is reported when doing SR-IOV hotplug with kernel built with lockdep:
BUG: sleeping function called from invalid context at kernel/sched/completion.c:93
in_atomic(): 1, irqs_disabled(): 1, pid: 1405, name: ip
3 locks held by ip/1405:
#0: (rtnl_mutex){+.+.+.}, at: [<ffffffff976b10bb>] rtnetlink_rcv+0x1b/0x40
#1: (&desc->request_mutex){+.+...}, at: [<ffffffff970ddd33>] __setup_irq+0xb3/0x720
#2: (&irq_desc_lock_class){-.-...}, at: [<ffffffff970ddd65>] __setup_irq+0xe5/0x720
irq event stamp: 3476
hardirqs last enabled at (3475): [<ffffffff971b3005>] get_page_from_freelist+0x225/0xc90
hardirqs last disabled at (3476): [<ffffffff978024e7>] _raw_spin_lock_irqsave+0x27/0x90
softirqs last enabled at (2446): [<ffffffffc05ef0b0>] ixgbevf_configure+0x380/0x7c0 [ixgbevf]
softirqs last disabled at (2444): [<ffffffffc05ef08d>] ixgbevf_configure+0x35d/0x7c0 [ixgbevf]
The workaround is to poll for host response instead of blocking on
completion.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We don't want slower IRQ handlers impacting faster devices that happen to
be assigned the same VMD interrupt vector. The driver was trying to
separate such devices by checking if MSI-X wasn't used, but really we just
don't want endpoint devices to share with bridges. Most bridges may use MSI
currently, so that criteria happened to work, but newer ones may use MSI-X,
so this patch explicitly checks the device type when choosing a vector.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The driver has a special purpose for the VMD device's first IRQ, so this
one shouldn't be considered for IRQ affinity.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls to
explicitly state whether the driver needs exclusive or shared reset control
behavior. Convert all drivers requesting exclusive resets to the explicit
API call so the temporary transition helpers can be removed.
No functional changes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
pci_scan_root_bus_bridge() returns zero for success, or a negative errno.
A typo in ae13cb9b19 ("PCI: rockchip: Convert PCI scan API to
pci_scan_root_bus_bridge()") treated zero as a failure.
Fix the typo.
Fixes: ae13cb9b19 ("PCI: rockchip: Convert PCI scan API to pci_scan_root_bus_bridge()")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This driver is required to work around several hardware bugs in the PCIe
controller.
The SMP8759 does not support legacy interrupts or IO space.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
[bhelgaas: add CONFIG_BROKEN dependency, various cleanups]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/host-rockchip:
PCI: rockchip: Use normal register bank for config accessors
PCI: rockchip: Use local struct device pointer consistently
PCI: rockchip: Check for clk_prepare_enable() errors during resume
MAINTAINERS: Remove Wenrui Li as Rockchip PCIe driver maintainer
PCI: rockchip: Configure RC's MPS setting
PCI: rockchip: Reconfigure configuration space header type
PCI: rockchip: Split out rockchip_pcie_cfg_configuration_accesses()
PCI: rockchip: Move configuration accesses into rockchip_pcie_cfg_atu()
PCI: rockchip: Rename rockchip_cfg_atu() to rockchip_pcie_cfg_atu()
PCI: rockchip: Control vpcie0v9 for system PM
Rockchip's RC has two banks of registers for the root port: a normal bank
that is strictly compatible with the PCIe spec, and a privileged bank that
can be used to change RO bits of root port registers.
When probing the RC driver, we use the privileged bank to do some basic
setup work as some RO bits are hw-inited to wrong value. But we didn't
change to the normal bank after probing the driver.
This leads to a serious problem when the PME code tries to clear the PME
status by writing PCI_EXP_RTSTA_PME to the register of PCI_EXP_RTSTA. Per
PCIe 3.0 spec, section 7.8.14, the PME status bit is RW1C. So the PME code
is doing the right thing to clear the PME status but we find the RC doesn't
clear it but actually setting it to one. So finally the system trap in
pcie_pme_work_fn() as PCI_EXP_RTSTA_PME is true now forever. This issue
can be reproduced by booting kernel with pci=nomsi.
Use the normal register bank for the PCI config accessors. The privileged
bank is used only internally by this driver.
Fixes: e77f847d ("PCI: rockchip: Add Rockchip PCIe controller support")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Brian Norris <briannorris@chromium.org>
* pci/host-hv:
PCI: hv: Use vPCI protocol version 1.2
PCI: hv: Add vPCI version protocol negotiation
PCI: hv: Temporary own CPU-number-to-vCPU-number infra
PCI: hv: Use page allocation for hbus structure
PCI: hv: Fix comment formatting and use proper integer fields
of_device_ids are not supposed to change at runtime. All functions working
with of_device_ids provided by <linux/of.h> work with const of_device_ids.
So mark the non-const structs as const.
File size before:
text data bss dec hex filename
195 600 0 795 31b drivers/pci/host/pcie-xilinx.o
File size after constify xilinx_pcie_of_match:
text data bss dec hex filename
595 184 0 779 30b drivers/pci/host/pcie-xilinx.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Add spinlock for protecting legacy mask register
- Few wifi end points which only support legacy interrupts, performs
hardware reset functionalities after disabling interrupts by invoking
disable_irq() and then re-enable using enable_irq(), they enable hardware
interrupts first and then virtual IRQ line later.
- The legacy IRQ line goes low only after DEASSERT_INTx is received. As
the legacy IRQ line is high immediately after hardware interrupts are
enabled but virq of EP is still in disabled state and EP handler is never
executed resulting no DEASSERT_INTx. If dummy IRQ chip is used,
interrupts are not masked and system hangs with CPU stall.
- Add IRQ chip functions instead of dummy IRQ chip for legacy interrupts.
- Legacy interrupts are level sensitive, so using handle_level_irq() is
more appropriate as it is masks interrupts until Endpoint handles
interrupts and unmasks interrupts after Endpoint handler is executed.
- Legacy interrupts are level triggered, virtual IRQ line of EndPoint shows
as edge in /proc/interrupts.
- Set IRQ flags of virtual IRQ line of EP to level triggered at the time of
mapping.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Recent __call_srcu() changes have exposed that we need to cleanup SRCU
structures after pci_stop_root_bus() calls into vmd_msi_free().
Fixes: 3906b91844 ("PCI: vmd: Use SRCU as a local RCU to prevent delaying global RCU")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Cc: <stable@vger.kernel.org> # 4.11
VMD domains are allocated starting at 0x10000, not 0x1000 as the comment
said. Correct the comment and add a reference to the ACPI spec for _SEG.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI host bridge found on Tegra SoCs doesn't require the MSI target
address to be backed by physical system memory. Writes are intercepted
within the controller and never make it to the memory pointed to.
Since no actual system memory is required, remove the allocation of a
single page and hardcode the MSI target address with a special address that
maps to the last 4 KiB page within the range that is reserved for system
memory and memory-mapped I/O in the FPCI address map.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
The MSI target address can reside beyond the 32-bit boundary on devices
with more than 2 GiB of system memory. The PCI host bridge on Tegra can
easily support 64-bit addresses, so make sure to pass the upper 32 bits of
the target address to endpoints when allocating MSI entries.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
We have a local "struct device *dev" in rockchip_pcie_probe(). Use it
consistently throughout the function. No functional change intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The default value of MPS for RC is 128 bytes, but actually it could support
256 bytes. So this patch fixes this issue.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe base specification (Revision 3.1a), section 7.5.3, type 1
configuration space header should be used when accessing PCIe switch. So
we need to reconfigure the header according to the bus number we are
accessing. Otherwise we could not visit the buses behind the switch.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We need to reconfigure the header type later, so split out a new function.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Configuration accesses is also part of ATU settings, so let's keep all of
them inside rockchip_pcie_cfg_atu().
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
