I need this to be able to apply the deferred fbdev setup patches, I
need the relevant prep work that landed through the drm-intel tree.
Also squash in conflict fixup from Laurent Pinchart.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HDMI 1.4b support the CEA video modes as per range of CEA-861-D (VIC 1-64).
For any other mode, the VIC filed in AVI infoframes should be 0.
HDMI 2.0 sinks, support video modes range as per CEA-861-F spec, which is
extended to (VIC 1-107).
This patch adds a bool input variable, which indicates if the connected
sink is a HDMI 2.0 sink or not. This will make sure that we don't pass a
HDMI 2.0 VIC to a HDMI 1.4 sink.
This patch touches all drm drivers, who are callers of this function
drm_hdmi_avi_infoframe_from_display_mode but to make sure there is
no change in current behavior, is_hdmi2 is kept as false.
In case of I915 driver, this patch:
- checks if the connected display is HDMI 2.0.
- HDMI infoframes carry one of this two type of information:
- VIC for 4K modes for HDMI 1.4 sinks
- S3D information for S3D modes
As CEA-861-F has already defined VICs for 4K videomodes, this
patch doesn't allow sending HDMI infoframes for HDMI 2.0 sinks,
until the mode is 3D.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jose Abreu <jose.abreu@synopsys.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
PS: This patch touches a few lines in few files, which were
already above 80 char, so checkpatch gives 80 char warning again.
- gpu/drm/omapdrm/omap_encoder.c
- gpu/drm/i915/intel_sdvo.c
V2: Rebase, Added r-b from Andrzej
V3: Addressed review comment from Ville:
- Do not send VICs in both AVI-IF and HDMI-IF
send only one of it.
V4: Rebase
V5: Added r-b from Neil.
Addressed review comments from Ville
- Do not block HDMI vendor IF, instead check for VIC while
handling AVI infoframes
V6: Rebase
V7: Rebase
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1499960000-9232-2-git-send-email-shashank.sharma@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm, I think I've got one later
driver pull for mediatek SoC driver, I'm undecided on if it needs to
go to you yet.
Otherwise summary below:
Core drm:
- Atomic add driver private objects
- Deprecate preclose hook in modern drivers
- MST bandwidth tracking
- Use kvmalloc in more places
- Add mode_valid hook for crtc/encoder/bridge
- Reduce sync_file construction time
- Documentation updates
- New DRM synchronisation object support
New drivers:
- pl111 - pl111 CLCD display controller
Panel:
- Innolux P079ZCA panel driver
- Add NL12880B20-05, NL192108AC18-02D, P320HVN03 panels
- panel-samsung-s6e3ha2: Add s6e3hf2 panel support
i915:
- SKL+ watermark fixes
- G4x/G33 reset improvements
- DP AUX backlight improvements
- Buffer based GuC/host communication
- New getparam for (sub)slice infomation
- Cannonlake and Coffeelake initial patches
- Execbuf optimisations
radeon/amdgpu:
- Lots of Vega10 bug fixes
- Preliminary raven support
- KIQ support for compute rings
- MEC queue management rework
- DCE6 Audio support
- SR-IOV improvements
- Better radeon/amdgpu selection support
nouveau:
- HDMI stereoscopic support
- Display code rework for >= GM20x GPUs
msm:
- GEM rework for fine-grained locking
- Per-process pagetable work
- HDMI fixes for Snapdragon 820.
vc4:
- Remove 256MB CMA limit from vc4
- Add out-fence support
- Add support for cygnus
- Get/set tiling ioctls support
- Add T-format tiling support for scanout
zte:
- add VGA support.
etnaviv:
- Thermal throttle support for newer GPUs
- Restore userspace buffer cache performance
- dma-buf sync fix
stm:
- add stm32f429 display support
exynos:
- Rework vblank handling
- Fixup sw-trigger code
sun4i:
- V3s display engine support
- HDMI support for older SoCs
- Preliminary work on dual-pipeline SoCs.
rcar-du:
- VSP work
imx-drm:
- Remove counter load enable from PRE
- Double read/write reduction flag support
tegra:
- Documentation for the host1x and drm driver.
- Lots of staging ioctl fixes due to grate project work.
omapdrm:
- dma-buf fence support
- TILER rotation fixes"
* tag 'drm-for-v4.13' of git://people.freedesktop.org/~airlied/linux: (1270 commits)
drm: Remove unused drm_file parameter to drm_syncobj_replace_fence()
drm/amd/powerplay: fix bug fail to remove sysfs when rmmod amdgpu.
amdgpu: Set cik/si_support to 1 by default if radeon isn't built
drm/amdgpu/gfx9: fix driver reload with KIQ
drm/amdgpu/gfx8: fix driver reload with KIQ
drm/amdgpu: Don't call amd_powerplay_destroy() if we don't have powerplay
drm/ttm: Fix use-after-free in ttm_bo_clean_mm
drm/amd/amdgpu: move get memory type function from early init to sw init
drm/amdgpu/cgs: always set reference clock in mode_info
drm/amdgpu: fix vblank_time when displays are off
drm/amd/powerplay: power value format change for Vega10
drm/amdgpu/gfx9: support the amdgpu.disable_cu option
drm/amd/powerplay: change PPSMC_MSG_GetCurrPkgPwr for Vega10
drm/amdgpu: Make amdgpu_cs_parser_init static (v2)
drm/amdgpu/cs: fix a typo in a comment
drm/amdgpu: Fix the exported always on CU bitmap
drm/amdgpu/gfx9: gfx_v9_0_enable_gfx_static_mg_power_gating() can be static
drm/amdgpu/psp: upper_32_bits/lower_32_bits for address setup
drm/amd/powerplay/cz: print message if smc message fails
drm/amdgpu: fix typo in amdgpu_debugfs_test_ib_init
...
ALSA SoC needs to know connected DAI ID for probing.
It is not a big problem if device/driver was only for sound,
but getting DAI ID will be difficult if device includes both
Video/Sound, like HDMI.
To solve this issue, this patch adds new .get_dai_id callback
on hdmi_codec_ops.
dw-hdmi-i2s will assume that HDMI sound will be connected
to reg = <2>. Then, ALSA SoC side will recognized it as DAI 0
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
/* HDMI Video IN */
};
port@1 {
reg = <1>;
/* HDMI OUT */
};
port@2 {
reg = <2>;
/* HDMI Sound IN */
};
};
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the audio sampler clock is enabled from dw_hdmi_setup() at
step E. and is kept enabled for later use. This clock should be enabled
and disabled along with the actual audio stream and not always on (that
is bad for PM). Furthermore, as described by the datasheet, the I2S
variant needs to gate/ungate the clock when the stream is
enabled/disabled.
This commit adds a parameter to hdmi_audio_enable_clk() that controls
when the audio sample clock must be enabled or disabled. Then, it adds
the call to this function from dw_hdmi_i2s_audio_enable() and
dw_hdmi_i2s_audio_disable().
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170414083113.4255-3-romain.perier@collabora.com
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Currently, CTS+N is forced to zero as a workaround of the IP block for
i.MX platforms. This is requested in the datasheet of the corresponding
IP for AHB mode only. However, we have seen that it introduces glitches
or delays when playing a sound on HDMI for I2S mode. This proves that we
cannot keep the current functions for handling audio stream as-is if
these contain workaround that are specific to a mode.
This commit introduces two callbacks, one for each variant.
dw_hdmi_setup defines the right function depending on the detected
variant. Then, the exported functions dw_hdmi_audio_enable and
dw_hdmi_audio_disable calls the corresponding callbacks
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170414083113.4255-2-romain.perier@collabora.com
This helper is supposed to validate or reject the modeline before it
applied by the mode setting. Currently this function has been dropped,
it was previously set to a dummy function that always returned true. For
both cases, this means that userspace can ask for a bad modeline that
will be always accepted.
On some platforms, like Rockchip, the drm dw_hdmi-rockchip variant driver
already implements the atomic_check drm helper, so mode_fixup cannot be
handled and implemented there (as drm_atomic_helper relies on either
atomic_check or mode_fixup).
This commit implements this helper. It only checks that this mode is
correct from the connector point of view.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170407121743.4142-1-romain.perier@collabora.com
The plat_data->input_bus_format and plat_data->input_bus_encoding
are unsigned long and are always >=0, but the value 0 was still
considered as RGB888 for input_bus_format and default color space
for input_bus_encoding in the reworked code.
This patch changes the if statement check for a non-zero value to
either use the default input bus_format and/or bus_encoding for a zero
value and the provided bus_format and/or bus_encoding for a
non zero value.
Thanks to Dan Carpenter for his bug report at [1].
Tested on Amlogic P230 (with CSC enabled for YUV444 to RGB) and Rockchip
RK3288 ACT8846 EVB Board (no CSC involved, direct RGB passthrough).
[1] http://lkml.kernel.org/r/20170406052120.GA26578@mwanda
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: def23aa7e9 ("drm: bridge: dw-hdmi: Switch to V4L bus format and encodings")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
[narmstrong@baylibre.com: reworded commit message and added Fixes tag]
Link: http://patchwork.freedesktop.org/patch/msgid/1491471244-24989-1-git-send-email-narmstrong@baylibre.com
The HDMI TX controller support HPD and RXSENSE signaling from the PHY
via it's STAT0 PHY interface, but some vendor PHYs can manage these
signals independently from the controller, thus these STAT0 handling
should be moved to PHY specific operations and become optional.
The existing STAT0 HPD and RXSENSE handling code is refactored into
a supplementaty set of default PHY operations that are used automatically
when the platform glue doesn't provide its own operations.
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1491309119-24220-2-git-send-email-narmstrong@baylibre.com
Switch code to use the newly introduced V4L bus formats IDs instead of custom
defines. Also use the V4L encoding defines.
Some display pipelines can only provide non-RBG input pixels to the HDMI TX
Controller, this patch takes the pixel format from the plat_data if provided.
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In preparation for adding PHY operations to handle RX SENSE and HPD,
group all the PHY interrupt setup code in a single location and extract
it to a separate function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
[narmstrong: renamed dw_hdmi_fb_registered to dw_hdmi_setup_i2c]
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Currently, the irq handler that monitors changes for HPD and RX_SENSE
relies on the status of the bridge for updating the status of the HPD.
The update is done only when the bridge is enabled.
However, on Rockchip platforms we have found use cases where it could be
a problem. When HDMI is being used, turning off/on the screen or
unplugging/re-plugging the cable, the following simplified code path
will happen:
- dw_hdmi_irq() will be triggered by an HPD event, as the bridge is on
hdmi->disabled is false, then the handler will update the rxsense flag
accordingly.
- dw_hdmi_update_power() will be invoked with the mode
DRM_FORCE_UNSPECIFIED and rxsense == 1, so dw_hdmi_poweroff() will be
called and the PHY will be desactivated (its pixel clocks and TMDS)
[...]
- dw_hdmi_bridge_disable() will be invoked, the bridge will be marked as
disabled.
- dw_hdmi_irq() will be triggered by an HPD event, as the bridge is
currently disabled the HPD status won't be updated, so hdmi->rxsense
won't be changed. Even if the data part of the PHY is disabled, this
information coming from the HDMI Transmitter is correct and should be
saved.
[...]
- dw_hdmi_bridge_enable() will be invoked, the bridge will be marked as
enabled.
- dw_hdmi_update_power() will be called. When hdmi->force is equal to
DRM_FORCE_UNSPECIFIED the function will rely on hdmi->rxsense. If this
field has not been updated by the irq handler, it will be false and
DRM_FORCE_ON won't be put to hdmi->force.
Consequently, most of the time dw_hdmi_poweron() won't be called in this
use case, TMDS won't be re-enabled the PHY won't be re-initialized,
resulting in a "Signal not found".
This commit fixes the issue by removing the check for "!hdmi->disabled".
As already explained, even if the PHY is partially disabled, information
coming from HDMI Transmitter about HPD should be saved for a later use.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/143602/
