The size field of the memory node is wrong. Rely on the default value in
sama5d2.dtsi that happens to be correct for the SAMA5D2 Xplained board.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add nodes to support the Controller Area Network(M_CAN) on SAMA5D2.
The version of M_CAN IP core is 3.1.0 (CREL = 0x31040730).
As said in SAMA5D2 datasheet, the CAN clock is recommended to use
frequencies of 20, 40 or 80 MHz. To achieve these frequencies,
PMC GCLK3 must select the UPLLCK(480 MHz) as source clock and
divide by 24, 12, or 6. So, the "assigned-clock-rates" property
has three options: 20000000, 40000000, and 80000000.
The "assigned-clock-parents" property should be referred to utmi
fixedly.
The MSBs [bits 31:16] of the CAN Message RAM for CAN0 and CAN1 are
default configured in 0x00200000. To avoid conflict with SRAM map
for PM, change them to 0x00210000 in the AT91Bootstrap via setting
the CAN Memories Address-based Register(SFR_CAN) of SFR.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Due to introducing the new driver - ACT8945A MFD drive,
change the pmic device node to align with the ACT8945A
regulator and charger drivers.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add the SAMA5D2-Compatible Shutdown Controller node to sama5d2.dtsi
and the use of it in the sama5d2 Xplained board dts file.
Enable the RTC wakeup event and the "wake up" button support through the
input "0" that is present on the board.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Merge "at91: dt for 4.6 #2" from Nicolas Ferre:
Second 4.6 DT series, all patches for sama5d2 and its Xplained board:
- addition of the NAND flash node
- addition of the dma properties for UART/USART nodes
- one update of the sama5d2 Xplained phy node
- addition of USB pinmux, button and leds
* tag 'at91-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: dts: at91: sama5d2 Xplained: add leds node
ARM: dts: at91: sama5d2 Xplained: add user push button
ARM: dts: at91: sama5d2 Xplained: set pin muxing for usb gadget and usb host
ARM: dts: at91: sama5d2: add nand0 and nfc0 nodes
ARM: dts: at91: sama5d2: add dma properties to UART nodes
ARM: dts: at91: sama5d2 Xplained: Correct the macb irq pinctrl node
Add the three leds on the sama5d2 Xplained board with their pinctrl node.
The blue led is positioned with the "heartbeat" trigger.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: add commit message and adapt to newer kernel]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
For USB gadget on port A (device mode):
- pin PA31 is configured as an input GPIO which triggers an interrupt when
vbus is detected on USB port A.
- pin PB9 is configured as an output GPIO and set to low level so the
board doesn't supply vbus to USB port A.
For USB host:
- pin PB10 is configured as an output GPIO and is active at high level.
The ohci driver will activate this pin so the board supplies vbus to USB
port B.
- pin PB9 should be configured as an output GPIO and active at high level
to use to USB port A in host mode (conflicts with USB gadget).
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
All pinctrl nodes for the Atmel pinctrl controller need to have their
bias configuration explicitly defined. Otherwise, the pinctrl mapping
is not valid.
It works for now as the pinctrl driver proceeds even with invalid
mappings, but this can become an issue, if the pinctrl driver starts
to require valid mappings. Additionally, the pin is not protected from
being remapped later by an other driver.
There is an external 1kOhms pull-up to 3.3V, so no bias is required on
the Ethernet PHY's interrupt line.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
DT changes for 4.6:
- Addition of the ADC for sama5d2 and sama5d2_xplained
* tag 'at91-ab-4.6-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: sama5d2 Xplained: enable the adc device
ARM: dts: at91: sama5d2: add adc device
Signed-off-by: Olof Johansson <olof@lixom.net>
After 57a38effa5 (net: phy: micrel: disable broadcast for KSZ8081/KSZ8091)
the macb0 interface has difficulties to come back from power saving mode if
address not explicitly set up.
As the micrel phy on the board is actually configured to show up at address 1
we use this explicitly.
Adding the phy node and its real address fixes the issue.
The phy IRQ and associated pinmux node is also added.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: stable@vger.kernel.org # 4.4+ // manual merge needed
Pull ARM DT updates from Olof Johansson:
"As usual, the bulk of this release is again DT file contents.
There's a huge number of changes here, and it's challenging to give a
crisp overview of just what is in here. To start with:
New boards:
- TI-based DM3730 from LogicPD (Torpedo)
- Cosmic+ M4 (nommu) initial support (Freescale Vybrid)
- Raspberry Pi 2 DT files
- Watchdog on Meson8b
- Veyron-mickey (ASUS Chromebit) DTS
- Rockchip rk3228 SoC and eval board
- Sigma Designs Tango4
Improvements:
- Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files
- Misc new devices for Rockchip rk3036 and rk3288
- Allwinner updates for misc SoCs and systems
... and a _large_ number of other changes across the field. Devices
added to SoC DTSI and board DTS files for a number of SoC vendors, new
product boards on already-supported SoCs, cleanups and refactorings of
existing DTS/DTSI files and a bunch of other changes"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (469 commits)
ARM: dts: compulab: add new board description
ARM: versatile: add the syscon LEDs to the DT
dts: vt8500: Fix errors in SDHC node for WM8505
ARM: dts: imx6q: clean up unused ipu2grp
ARM: dts: silk: Add compatible property to "partitions" node
ARM: dts: gose: Add compatible property to "partitions" node
ARM: dts: porter: Add compatible property to "partitions" node
ARM: dts: koelsch: Add compatible property to "partitions" node
ARM: dts: lager: Add compatible property to "partitions" node
ARM: dts: bockw: Add compatible property to "partitions" node
ARM: dts: meson8b: Add watchdog node
Documentation: watchdog: Add new bindings for meson8b
ARM: meson: Add status LED for Odroid-C1
ARM: dts: uniphier: fix a typo in comment block
ARM: bcm2835: Add the auxiliary clocks to the device tree.
ARM: bcm2835: Add devicetree for bcm2836 and Raspberry Pi 2 B
ARM: bcm2835: Move the CPU/peripheral include out of common RPi DT.
ARM: bcm2835: Split the DT for peripherals from the DT for the CPU
ARM: realview: set up cache correctly on the PB11MPCore
ARM: dts: Unify G2D device node with other devices on exynos4
...
Data have to be held longer for the PMIC device. The ACT8945A
datasheet claims that minimum SDA data hold time is about 300 ns.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As the SDHCI controller needs the 1.8V line to be always enabled for some eMMC
configurations, set the proper "regulator-always-on" property to the board DTS
files.
Note that the sdhci classical regulator definitions doesn't suit our controller
for this 1.8V purpose.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The clocks group properties and the clock@0 node are useless, remove them
to avoid copy pasting in future device trees.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add minimal support for the new sama5d2 Xplained board. Only USB,
spi/i2c, ethernet and uart/usart peripherals added.
With this DTS file you can boot the board and begin to play with it.
Rootfs on NFS and sd card have successfully been tested.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
