This reverts commit 2c17a4368a.
The offending commit triggers a run-time fault when accessing the panel
element of the sun4i_tcon structure when no such panel is attached.
It was apparently assumed in said commit that a panel is always used with
the TCON. Although it is often the case, this is not always true.
For instance a bridge might be used instead of a panel.
This issue was discovered using an A13-OLinuXino, that uses the TCON
in RGB mode for a simple DAC-based VGA bridge.
Cc: stable@vger.kernel.org
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613081647.31183-1-paul.kocialkowski@bootlin.com
The Allwinner A80 SoC has 2 documented TCONs. The display pipeline
diagram from the user manual shows a third TCON, but it's missing
an interrupt line, and its registers are not explained either.
It's also not used in Allwinner's vendor BSP.
The first TCON only has channel 0, for LCD panel output. The TCON
hardware setup is peculiar in that the eDP reset must also be
deasserted to allow access to the TCON. How the eDP module is wired
in the SoC itself is never explained.
The second TCON only has channel 1, and its output is connected to
the HDMI encoder block.
This patch adds a "needs_edp_reset" field to the tcon quirks structure,
and adds quirks and compatible strings for the 2 documented TCONs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180315114136.24747-4-wens@csie.org
Handle both positive and negative dclk polarity,
according to bus_flags, taking care of this:
On A20 and similar SoCs, the only way to achieve Positive Edge
(Rising Edge), is setting dclk clock phase to 2/3(240°).
By default TCON works in Negative Edge(Falling Edge), this is why phase
is set to 0 in that case.
Unfortunately there's no way to logically invert dclk through IO_POL
register.
The only acceptable way to work, triple checked with scope,
is using clock phase set to 0° for Negative Edge and set to 240° for
Positive Edge.
On A33 and similar SoCs there would be a 90° phase option, but it divides
also dclk by 2.
This patch is a way to avoid quirks all around TCON and DOTCLOCK drivers
for using A33 90° phase divided by 2 and consequently increase code
complexity.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1520963677-124239-1-git-send-email-giulio.benetti@micronovasrl.com
Currently the exclusivity is enabled when the rate is set by
the mode setting functions. These functions are called by
mode_set_nofb callback of drm_crc_helper. Then exclusivity
is disabled when tcon is disabled by atomic_disable
callback.
What happens is that mode_set_nofb can be called once when
mode changes, and afterwards the system can call atomic_enable
and atomic_disable multiple times without further calls to
mode_set_nofb.
This happens:
mode_set_nofb - clk exclusivity is enabled
atomic_enable
atomic_disable - clk exclusivity is disabled
atomic_enable
atomic_disable - clk exclusivity is already disabled, leading to WARN
in clk_rate_exclusive_put
Solution is to enable exclusivity in sun4i_tcon_channel_set_status.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180310110511.14697-1-megous@megous.com
I noticed that with 4.16-rc1 LVDS output on A83T based TBS A711 tablet doesn't
work (there's output but it's garbled). I compared some older patches for LVDS
support with the mainlined ones and this change is missing from mainline Linux.
I don't know what the register does exactly and the harcoded register value
doesn't inspire much confidence that it will work in a general case, so I'm
sending this RFC.
This patch fixes the issue on A83T.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222161217.23904-1-megous@megous.com
drm-misc-next for 4.17:
UAPI Changes:
- drm/vc4: Expose performance counters to userspace (Boris)
Cross-subsystem Changes:
- MAINTAINERS: Linus to maintain panel-arm-versatile in -misc (Linus)
Core Changes:
- Only use swiotlb when necessary (Chunming)
Driver Changes:
- drm/panel: Add support for ARM Versatile panels (Linus)
- pl111: Improvements around versatile panel support (Linus)
----------------------------------------
Tagged on 2018-02-06:
drm-misc-next for 4.17:
UAPI Changes:
- Validate mode flags + type (Ville)
- Deprecate unused mode flags PIXMUX, BCAST (Ville)
- Deprecate unused mode types BUILTIN, CRTC_C, CLOCK_C, DEFAULT (Ville)
Cross-subsystem Changes:
- MAINTAINERS: s/Daniel/Maarten/ for drm-misc (Daniel)
Core Changes:
- gem: Export gem functions for drivers to use (Samuel)
- bridge: Introduce bridge timings in drm_bridge (Linus)
- dma-buf: Allow exclusive fence to be bundled in fence array when
calling reservation_object_get_fences_rcu (Christian)
- dp: Add training pattern 4 and HBR3 support to dp helpers (Manasi)
- fourcc: Add alpha bit to formats to avoid driver format LUTs (Maxime)
- mode: Various cleanups + add new device-wide .mode_valid hook (Ville)
- atomic: Fix state leak when non-blocking commits fail (Leo)
NOTE: IIRC, this was cross-picked to -fixes so it might fall out
- crc: Allow polling on the data fd (Maarten)
Driver Changes:
- bridge/vga-dac: Add THS8134* support (Linus)
- tinydrm: Various MIPI DBI improvements/cleanups (Noralf)
- bridge/dw-mipi-dsi: Cleanups + use create_packet helper (Brian)
- drm/sun4i: Add Display Engine frontend support (Maxime)
- drm/sun4i: Add zpos support + increase num planes from 2 to 4 (Maxime)
- various: Use drm_mode_get_hv_timing() to fill plane clip rectangle (Ville)
- stm: Add 8-bit clut support, add dsi phy v1.31 support, +fixes (Phillipe)
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Chunming Zhou <david1.zhou@amd.com>
Cc: Samuel Li <Samuel.Li@amd.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
* tag 'drm-misc-next-2018-02-13' of git://anongit.freedesktop.org/drm/drm-misc: (115 commits)
drm/radeon: only enable swiotlb path when need v2
drm/amdgpu: only enable swiotlb alloc when need v2
drm: add func to get max iomem address v2
drm/vc4: Expose performance counters to userspace
drm: Print the pid when debug logging an ioctl error.
drm/stm: ltdc: remove non-alpha color formats on layer 2 for older hw
drm/stm: ltdc: add non-alpha color formats
drm/bridge/synopsys: dsi: Add 1.31 version support
drm/bridge/synopsys: dsi: Add read feature
drm/pl111: Support multiple endpoints on the CLCD
drm/pl111: Support variants with broken VBLANK
drm/pl111: Support variants with broken clock divider
drm/pl111: Handle the Versatile RGB/BGR565 mode
drm/pl111: Properly detect the ARM PL110 variants
drm/panel: Add support for ARM Versatile panels
drm/panel: Device tree bindings for ARM Versatile panels
drm/bridge: Rename argument from crtc to bridge
drm/crc: Add support for polling on the data fd.
drm/sun4i: Use drm_mode_get_hv_timing() to populate plane clip rectangle
drm/rcar-du: Use drm_mode_get_hv_timing() to populate plane clip rectangle
...
Fixes for 4.16:
Fixes one Kconfig issue and a enable some panels to work properly.
There is also a fix of error code return in sun4i.
* tag 'drm-misc-next-fixes-2018-01-18' of git://anongit.freedesktop.org/drm/drm-misc:
drm: Fix PANEL_ORIENTATION_QUIRKS breaking the Kconfig DRM menuconfig
drm/panel: lvds: Handle the optional regulator case properly
drm/sun4i: Fix error code in sun4i_tcon_bind()
The sun4i DRM driver maintains a list of compatible strings it uses to
check if a device node within the display component graph is a TCON.
The TCON driver also has this list, used to bind the TCON driver to
the device. These two lists are identical.
Instead of maintaining two identical lists, export the list from the
TCON driver for the DRM driver to use.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171127084632.25511-1-wens@csie.org
The A20 display pipeline has 2 frontends, 2 backends, and 2 TCONs.
This patch adds support (or a compatible string in the frontend's
case) for these components.
The TCONs support directly outputting to CPU/RGB/LVDS LCD panels,
or it can output to HDMI via an on-chip HDMI controller, or
CVBS/YPbPr/VGA signals via on-chip TV encoders. These additional
encoders are not covered in this patch.
Signed-off-by: Jonathan Liu <net147@gmail.com>
[wens@csie.org: Expand commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171017121807.2994-6-wens@csie.org
The A10 has two TCONs that are similar to the ones found on other SoCs.
Like the A31, TCON0 has a register used to mux the TCON outputs to the
downstream encoders. The bit fields are slightly different.
Signed-off-by: Jonathan Liu <net147@gmail.com>
[wens@csie.org: Reworked for A10 and fixed up commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171017121807.2994-3-wens@csie.org
So far, we've required all the TCON-connected encoders to call the TCON
enable and disable functions.
This was made this way because in the RGB/LVDS case, the TCON is the CRTC
and the encoder. However, in all the other cases (HDMI, TV, DSI, etc.), we
have another encoder down the road that needs to be programmed.
We also needed to know which channel the encoder is connected to, which is
encoder-specific.
The CRTC's enable and disable callbacks can work just fine for our use
case, and we can get the channel to use just by looking at the type of
encoder, since that is fixed. Implement those callbacks, which will
remove some of the encoder boilerplate.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/90b4396e19b3eca61b2ebfdae0672074b88ad74d.1508231063.git-series.maxime.ripard@free-electrons.com
Different SoCs have different muxing options and values for the TCON
outputs. Instead of stuffing every possibility in sun4i_tcon_set_mux(),
add a callback pointer to sun4i_tcon_quirks that each TCON variant
can use to provide muxing support.
The current muxing options in sun4i_tcon_set_mux() for sun5i-a13 are
moved to a new sun5i-specific callback function.
Since the new callback replaces what the .has_unknown_mux field in
tcon quirks did in the past, the field is removed.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010032008.682-2-wens@csie.org
The TCON has a mux to select the source of the data to display.
This mux includes selecting the display backends. On the A31,
which has two display pipelines, this mux can let the TCON
select either backend as its data source. Although the muxing
can be changed on the fly, DRM needs to be able to group a
bunch of layers such that they get switched to another crtc
together. This is because the display backend does the layer
compositing, while the TCON generates the display timings.
This constraint is not supported by DRM.
Here we simply pair up backends and TCONs with the same ID.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908075016.18657-7-wens@csie.org
The device tree binding for sun4i-drm says:
For all connections between components up to the TCONs in the display
pipeline, when there are multiple components of the same type at the
same depth, the local endpoint ID must be the same as the remote
component's index. For example, if the remote endpoint is Frontend 1,
then the local endpoint ID must be 1.
We should be able to get the TCON's ID directly from any of the remote
endpoints from its input port. With the ID, we can then go through the
list of registered engines and find a matching one by ID.
However the A31 device tree is incorrect. We assumed that there were no
cross pipeline connections between the backends and TCONs. As a result,
in all the endpoints between the backends and TCONs of the second
display pipeline, the endpoint IDs were incorrectly set to 0, when in
fact they should've been set to 1.
To maintain compatibility with this incorrect device tree, we first
check if the TCON's input port has 1 or many endpoints. If there are
more than 1, then it is likely a fixed version, and we can proceed
with the new method. If there is only 1 endpoint, then it is possibly
an incorrect version, or it could be the SoC only has one pipeline.
In either case we fall back to using the old method of traversing
the input connections to find a matching engine, and then get its
ID.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908075016.18657-5-wens@csie.org
The patch b317fa3ba1 ("drm/sun4i: tcon: Find matching display backend
by device node matching") assumed a one-to-one mapping between TCONs
and backends. This turned out wrong, as we found muxing controls in the
TCON of the A31, and undocumented usage of the backend output selector
of the A20.
Make sun4i_tcon_find_engine() bail out if the current node has multiple
input connections.
Fixes: b317fa3ba1 ("drm/sun4i: tcon: Find matching display backend
by device node matching")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908075016.18657-4-wens@csie.org
When binding the TCON, we were checking the reset control status and
asserting reset if it wasn't in reset. The check failed to account for
the reset control API returning error codes if the status callback was
not implemented.
Since we want the TCON to be reset in all cases, use reset_control_reset
to force a reset instead.
Fixes: 9026e0d122 ("drm: Add Allwinner A10 Display Engine support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908090016.32224-1-wens@csie.org
It appears that the total vertical resolution needs to be doubled when
we're not in interlaced. Make sure that is the case.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Both TCON channels need to have the resolution doubled, since the size the
hardware is going to use is whatever we put in the register divided by two.
However, we handle it differently for the two channels: in the channel 0,
our register access macro does the multiplication of the value passed as
paremeter, while in the channel 1, the macro doesn't do this, and we need
to do it before calling it.
Make this consistent by aligning the channel 0 with the channel 1
behaviour.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
It seems like what's called a backporch in the datasheet is actually the
backporch plus the sync period. Fix that in our driver.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The muxing can actually happen on both channels on some SoCs, so it makes
more sense to just move it out of the sun4i_tcon1_mode_set function and
create a separate function that needs to be called by the encoders.
Let's do that and convert the existing drivers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
While all functions have debug logs, the channel enable and disable are not
logged. Make sure this is the case.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As we are going to add support for the Allwinner DE2 engine in sun4i-drm
driver, we will finally have two types of display engines -- the DE1
backend and the DE2 mixer. They both do some display blending and feed
graphics data to TCON, and is part of the "Display Engine" called by
Allwinner, so I choose to call them both "engine" here.
Abstract the engine type to a new struct with an ops struct, which contains
functions that should be called outside the engine-specified code (in
TCON, CRTC or TV Encoder code).
In order to preserve bisectability, we also switch the backend and layer
code in its own module.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Currently we are configuring the TCON's dot clock or special clock
directly from the encoder mode_set functions. Since we already
provide mode_set helper functions for the TCON's 2 channels, we
can set the respective clock from those helpers, and reduce the
exposure of the TCON's internals.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The tcons and backends have a one-to-one relationship. Their IDs,
or indexes in the documentation, are also the same.
Copy the ID from the associated backend and save it in the tcon
structure. This will later be used when we add support for the
output data path muxes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
