Pull smp hotplug updates from Thomas Gleixner:
"This is the final round of converting the notifier mess to the state
machine. The removal of the notifiers and the related infrastructure
will happen around rc1, as there are conversions outstanding in other
trees.
The whole exercise removed about 2000 lines of code in total and in
course of the conversion several dozen bugs got fixed. The new
mechanism allows to test almost every hotplug step standalone, so
usage sites can exercise all transitions extensively.
There is more room for improvement, like integrating all the
pointlessly different architecture mechanisms of synchronizing,
setting cpus online etc into the core code"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
tracing/rb: Init the CPU mask on allocation
soc/fsl/qbman: Convert to hotplug state machine
soc/fsl/qbman: Convert to hotplug state machine
zram: Convert to hotplug state machine
KVM/PPC/Book3S HV: Convert to hotplug state machine
arm64/cpuinfo: Convert to hotplug state machine
arm64/cpuinfo: Make hotplug notifier symmetric
mm/compaction: Convert to hotplug state machine
iommu/vt-d: Convert to hotplug state machine
mm/zswap: Convert pool to hotplug state machine
mm/zswap: Convert dst-mem to hotplug state machine
mm/zsmalloc: Convert to hotplug state machine
mm/vmstat: Convert to hotplug state machine
mm/vmstat: Avoid on each online CPU loops
mm/vmstat: Drop get_online_cpus() from init_cpu_node_state/vmstat_cpu_dead()
tracing/rb: Convert to hotplug state machine
oprofile/nmi timer: Convert to hotplug state machine
net/iucv: Use explicit clean up labels in iucv_init()
x86/pci/amd-bus: Convert to hotplug state machine
x86/oprofile/nmi: Convert to hotplug state machine
...
8xx uses a two level page table with two different linux page size
support (4k and 16k). 8xx also support two different hugepage sizes
512k and 8M. In order to support them on linux we define two different
page table layout.
The size of pages is in the PGD entry, using PS field (bits 28-29):
00 : Small pages (4k or 16k)
01 : 512k pages
10 : reserved
11 : 8M pages
For 512K hugepage size a pgd entry have the below format
[<hugepte address >0101] . The hugepte table allocated will contain 8
entries pointing to 512K huge pte in 4k pages mode and 64 entries in
16k pages mode.
For 8M in 16k mode, a pgd entry have the below format
[<hugepte address >1101] . The hugepte table allocated will contain 8
entries pointing to 8M huge pte.
For 8M in 4k mode, multiple pgd entries point to the same hugepte
address and pgd entry will have the below format
[<hugepte address>1101]. The hugepte table allocated will only have one
entry.
For the time being, we do not support CPU15 ERRATA when HUGETLB is
selected
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> (v3, for the generic bits)
Signed-off-by: Scott Wood <oss@buserror.net>
Pull powerpc fixes from Michael Ellerman:
"Four fixes, the first for code we merged this cycle and three that are
also going to stable:
- On 64-bit Book3E we were not placing the .text section where we
said we would in the asm.
- We broke building the boot wrapper on some 32-bit toolchains.
- Lazy icache flushing was broken on pre-POWER5 machines.
- One of the error paths in our EEH code would lead to a deadlock.
Thanks to: Andrew Donnellan, Ben Hutchings, Benjamin Herrenschmidt,
Nicholas Piggin"
* tag 'powerpc-4.9-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64: Fix placement of .text to be immediately following .head.text
powerpc/eeh: Fix deadlock when PE frozen state can't be cleared
powerpc/mm: Fix lazy icache flush on pre-POWER5
powerpc/boot: Fix build failure in 32-bit boot wrapper
There is no need to worry about module and __init text disappearing
case, because that ftrace has a module notifier that is called when a
module is being unloaded and before the text goes away and this code
grabs the ftrace_lock mutex and removes the module functions from the
ftrace list, such that it will no longer do any modifications to that
module's text, the update to make functions be traced or not is done
under the ftrace_lock mutex as well. And by now, __init section codes
should not been modified by ftrace, because it is black listed in
recordmcount.c and ignored by ftrace.
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Li Bin <huawei.libin@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We are going to get rid of @current references in mmu_context_boos3s64.c
and cache mm_struct in the VFIO container. Since mm_context_t does not
have reference counting, we will be using mm_struct which does have
the reference counter.
This changes mm_iommu_init/mm_iommu_cleanup to receive mm_struct rather
than mm_context_t (which is embedded into mm).
This should not cause any behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current facility_strings[] are correct when the trap address is
0xf80 (hypervisor facility unavailable). When the trap address is
0xf60 (facility unavailable) IC (Interruption Cause) a.k.a status in the
code is undefined for values 0 and 1.
Add a check to prevent printing the (misleading) facility name for IC 0
and 1 when we came in via 0xf60. In all cases, print the actual IC
value, to avoid any confusion.
This hasn't been seen on real hardware, on only qemu which was
misreporting an exception.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Fix indentation, combine printks(), massage change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Do not introduce any additional alignment. Placement of text section
will be set by fixed section macros. Without this, output section
alignment defaults to 4096, which makes BookE text section start at
0x1000 when it is expected to start at 0x100.
This was introduced by commit 57f266497d ("powerpc: Use gas sections
for arranging exception vectors") and was caught with the scripted head
section checker (not yet merged).
Fixes: 57f266497d ("powerpc: Use gas sections for arranging exception vectors")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In eeh_reset_device(), we take the pci_rescan_remove_lock immediately after
after we call eeh_reset_pe() to reset the PCI controller. We then call
eeh_clear_pe_frozen_state(), which can return an error. In this case, we
bail out of eeh_reset_device() without calling pci_unlock_rescan_remove().
Add a call to pci_unlock_rescan_remove() in the eeh_clear_pe_frozen_state()
error path so that we don't cause a deadlock later on.
Reported-by: Pradipta Ghosh <pradghos@in.ibm.com>
Fixes: 7895470063 ("powerpc/eeh: Avoid I/O access during PE reset")
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we've defined structures to describe each of the client
architecture vectors, we can use those to construct the value we pass to
firmware.
This avoids the tricks we previously played with the W() macro, allows
us to properly endian annotate fields, and should help to avoid bugs
introduced by failing to have the correct number of zero pad bytes
between fields.
It also means we can avoid hard coding IBM_ARCH_VEC_NRCORES_OFFSET in
order to update the max_cpus value and instead just set it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The "client architecture vectors" are a series of structures we pass to
firmware to define various things, such as what processors we support
and many other options.
Each structure is entirely different so we have to define a different
struct for each one, but that's OK.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This purgatory implementation is based on the versions from kexec-tools
and kexec-lite, with additional changes.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds the support code needed for implementing
kexec_file_load() on powerpc.
This consists of functions to load the ELF kernel, either big or little
endian, and setup the purgatory enviroment which switches from the first
kernel to the second kernel.
None of this code is built yet, as it depends on CONFIG_KEXEC_FILE which
we have not yet defined. Although we could define CONFIG_KEXEC_FILE in
this patch, we'd then have a window in history where the kconfig symbol
is present but the syscall is not, which would be awkward.
Signed-off-by: Josh Sklar <sklar@linux.vnet.ibm.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 2965faa5e0 ("kexec: split kexec_load syscall from kexec core
code") introduced CONFIG_KEXEC_CORE so that CONFIG_KEXEC means whether
the kexec_load system call should be compiled-in and CONFIG_KEXEC_FILE
means whether the kexec_file_load system call should be compiled-in.
These options can be set independently from each other.
Since until now powerpc only supported kexec_load, CONFIG_KEXEC and
CONFIG_KEXEC_CORE were synonyms. That is not the case anymore, so we
need to make a distinction. Almost all places where CONFIG_KEXEC was
being used should be using CONFIG_KEXEC_CORE instead, since
kexec_file_load also needs that code compiled in.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This converts one that was missed by b1576fec7f ("powerpc: No need
to use dot symbols when branching to a function").
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
From 80f23935ca ("powerpc: Convert cmp to cmpd in idle enter sequence"):
PowerPC's "cmp" instruction has four operands. Normally people write
"cmpw" or "cmpd" for the second cmp operand 0 or 1. But, frequently
people forget, and write "cmp" with just three operands.
With older binutils this is silently accepted as if this was "cmpw",
while often "cmpd" is wanted. With newer binutils GAS will complain
about this for 64-bit code. For 32-bit code it still silently assumes
"cmpw" is what is meant.
In this case, cmpwi is called for, so this is just a build fix for
new toolchains.
Cc: stable@vger.kernel.org # v3.0+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- Set missing wakeup bit in LPCR on POWER9
- Fix the early OPAL console wrappers
- Fixup kernel read only mapping
Fixes for code merged this cycle:
- Fix missing CRCs, add more asm-prototypes.h declarations"
* tag 'powerpc-4.9-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fixup kernel read only mapping
powerpc/boot: Fix the early OPAL console wrappers
powerpc: Fix missing CRCs, add more asm-prototypes.h declarations
powerpc: Set missing wakeup bit in LPCR on POWER9
Ensure that PSSCR is set to a safe value corresponding to no
state-loss each time a POWER9 CPU comes online.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-By: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 adds new capabilities to the tlbie (TLB invalidate entry)
and tlbiel (local tlbie) instructions. Both instructions get a
set of new parameters (RIC, PRS and R) which appear as bits in the
instruction word. The tlbiel instruction now has a second register
operand, which contains a PID and/or LPID value if needed, and
should otherwise contain 0.
This adapts KVM-HV's usage of tlbie and tlbiel to work on POWER9
as well as older processors. Since we only handle HPT guests so
far, we need RIC=0 PRS=0 R=0, which ends up with the same instruction
word as on previous processors, so we don't need to conditionally
execute different instructions depending on the processor.
The local flush on first entry to a guest in book3s_hv_rmhandlers.S
is a loop which depends on the number of TLB sets. Rather than
using feature sections to set the number of iterations based on
which CPU we're on, we now work out this number at VM creation time
and store it in the kvm_arch struct. That will make it possible to
get the number from the device tree in future, which will help with
compatibility with future processors.
Since mmu_partition_table_set_entry() does a global flush of the
whole LPID, we don't need to do the TLB flush on first entry to the
guest on each processor. Therefore we don't set all bits in the
tlb_need_flush bitmap on VM startup on POWER9.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds code to handle two new guest-accessible special-purpose
registers on POWER9: TIDR (thread ID register) and PSSCR (processor
stop status and control register). They are context-switched
between host and guest, and the guest values can be read and set
via the one_reg interface.
The PSSCR contains some fields which are guest-accessible and some
which are only accessible in hypervisor mode. We only allow the
guest-accessible fields to be read or set by userspace.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This merges in the ppc-kvm topic branch to get changes to
arch/powerpc code that are necessary for adding POWER9 KVM support.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Partially copied from commit df0698be14 ("ARM: stack protector:
change the canary value per task")
A new random value for the canary is stored in the task struct whenever
a new task is forked. This is meant to allow for different canary values
per task. On powerpc, GCC expects the canary value to be found in a global
variable called __stack_chk_guard. So this variable has to be updated
with the value stored in the task struct whenever a task switch occurs.
Because the variable GCC expects is global, this cannot work on SMP
unfortunately. So, on SMP, the same initial canary value is kept
throughout, making this feature a bit less effective although it is still
useful.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Partialy copied from commit c743f38013 ("ARM: initial stack protector
(-fstack-protector) support")
This is the very basic stuff without the changing canary upon
task switch yet. Just the Kconfig option and a constant canary
value initialized at boot time.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Invoke the kprobe handlers directly rather than through notify_die(), to
reduce path taken for handling kprobes. Similar to commit 6f6343f53d
("kprobes/x86: Call exception handlers directly from do_int3/do_debug").
While at it, rename post_kprobe_handler() to kprobe_post_handler() for
more uniform naming.
Reported-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Define and set the POWER9 HFSCR doorbell bit so that guests can use
msgsndp.
ISA 3.0 calls this MSGP, so name it accordingly in the code.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It is the reasonable expectation that if an executable file is not
readable there will be no way for a user without special privileges to
read the file. This is enforced in ptrace_attach but if ptrace
is already attached before exec there is no enforcement for read-only
executables.
As the only way to read such an mm is through access_process_vm
spin a variant called ptrace_access_vm that will fail if the
target process is not being ptraced by the current process, or
the current process did not have sufficient privileges when ptracing
began to read the target processes mm.
In the ptrace implementations replace access_process_vm by
ptrace_access_vm. There remain several ptrace sites that still use
access_process_vm as they are reading the target executables
instructions (for kernel consumption) or register stacks. As such it
does not appear necessary to add a permission check to those calls.
This bug has always existed in Linux.
Fixes: v1.0
Cc: stable@vger.kernel.org
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
There is a new bit, LPCR_PECE_HVEE (Hypervisor Virtualization Exit
Enable), which controls wakeup from STOP states on Hypervisor
Virtualization Interrupts (which happen to also be all external
interrupts in host or bare metal mode).
It needs to be set or we will miss wakeups.
Fixes: 9baaef0a22 ("powerpc/irq: Add support for HV virtualization interrupts")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Rename it to HVEE to match the name in the ISA]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_pe_reset and eeh_reset_pe are two different functions in the same
file which do mostly the same thing. Not only is this confusing, but
potentially causes disrepancies in functionality, notably eeh_reset_pe
as it does not check return values for failure.
Refactor this into the following:
- eeh_pe_reset(): stays as is, performs a single operation, exported
- eeh_pe_reset_full(): new, full reset process that calls eeh_pe_reset()
- eeh_reset_pe(): removed and replaced by eeh_pe_reset_full()
- eeh_reset_pe_once(): removed
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PHB, PE (and by association MVE) numbers are printed as a mix of decimal
and hexadecimal throughout the kernel. This can be misleading, so make
them all hexadecimal.
Standardising on hex instead of dec because:
- PHB numbers are presented in hex in sysfs/debugfs (and lspci, etc)
- PE numbers are presented as hex in sysfs and parsed in hex in debugfs
The only place I think this could cause confusing are the messages during
boot, i.e.
pci 000a:01 : [PE# 000] Secondary bus 1 associated with PE#0
which can be a quick way to check PE numbers. pe_level_printk() will
only print two characters instead of three, so the above would be
pci 000a:01 : [PE# 00] Secondary bus 1 associated with PE#0
which gives a hint it's in hex.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When switching from/to a guest that has a transaction in progress,
we need to save/restore the checkpointed register state. Although
XER is part of the CPU state that gets checkpointed, the code that
does this saving and restoring doesn't save/restore XER.
This fixes it by saving and restoring the XER. To allow userspace
to read/write the checkpointed XER value, we also add a new ONE_REG
specifier.
The visible effect of this bug is that the guest may see its XER
value being corrupted when it uses transactions.
Fixes: e4e3812150 ("KVM: PPC: Book3S HV: Add transactional memory support")
Fixes: 0a8eccefcb ("KVM: PPC: Book3S HV: Add missing code for transaction reclaim on guest exit")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- fix system reset interrupt winkle wakeups
- fix setting of AIL in hypervisor mode
Fixes for code merged this cycle:
- fix exception vector build with 2.23 era binutils
- fix missing update of HID register on secondary CPUs
Other:
- fix missing pr_cont()s
- invalidate ERAT on tlbiel for POWER9 DD1"
* tag 'powerpc-4.9-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fix missing update of HID register on secondary CPUs
powerpc/mm/radix: Invalidate ERAT on tlbiel for POWER9 DD1
powerpc/64: Fix setting of AIL in hypervisor mode
powerpc/oops: Fix missing pr_cont()s in instruction dump
powerpc/oops: Fix missing pr_cont()s in show_regs()
powerpc/oops: Fix missing pr_cont()s in print_msr_bits() et. al.
powerpc/oops: Fix missing pr_cont()s in show_stack()
powerpc: Fix exception vector build with 2.23 era binutils
powerpc/64s: Fix system reset interrupt winkle wakeups
The ibm_pa_features array consists of structures that describe which bit
and byte in the ibm,pa-features property toggles one or more flags in
either the CPU, MMU, or user visible feature flags.
Each one consists of 7 values, which are all unsigned long, int or char,
meaning the compiler gives us no warning if we assign the wrong values
to the wrong elements. In fact we have had a bug here in the past, where
we were setting incorrect bits, see commit 6997e57d69 ("powerpc:
scan_features() updates incorrect bits for REAL_LE").
So switch to using named initialisers for the structure elements, to
reduce the likelihood of future bugs, and hopefully improve readability
also.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
When ending an oops, don't clear die_owner unless the nest count
went to zero. This prevents a second nested oops from hanging forever
on the die_lock.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When exiting xmon with 'x' (exit and recover), oops_begin bails
out immediately, but die then calls __die() and oops_end(), which
cause a lot of bad things to happen.
If the debugger was attached then went to graceful recovery, exit
from die() immediately.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove the unused but set variable srr1 in save_mce_event() to
fix the following GCC warning when building with 'W=1':
arch/powerpc/kernel/mce.c:75:11: warning: variable 'srr1' set but not used
It has never been used.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix two [-Wold-style-declaration] GCC warnings by moving the inline
keyword before the return type.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit d3cbff1b5 "powerpc: Put exception configuration in a common place"
broke the setting of the AIL bit (which enables taking exceptions with
the MMU still on) on all processors, moving it incorrectly to a function
called only on the boot CPU. This was correct for the guest case but
not when running in hypervisor mode.
This fixes it by partially reverting that commit, putting the setting
back in cpu_ready_for_interrupts()
Fixes: d3cbff1b5a ("powerpc: Put exception configuration in a common place")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add comment clarifying that vio_find_node() takes a reference to the
embedded struct device which needs to be dropped after use.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make sure to drop any reference taken by bus_find_device() when creating
devices during init and driver registration.
Fixes: 55347cc996 ("[POWERPC] ibmebus: Add device creation and bus probing based on of_device")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make sure to drop any reference taken by bus_find_device() in the sysfs
callbacks that are used to create and destroy devices based on
device-tree entries.
Fixes: 6bccf755ff ("[POWERPC] ibmebus: dynamic addition/removal of adapters, some code cleanup")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Load monitored is no longer supported on POWER9 so let's remove the
code.
This reverts commit bd3ea317fd ("powerpc: Load Monitor Register
Support").
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a config option that can help exercise the case when
the kernel is not running at PAGE_OFFSET.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
