Since we are now using the clock API integration to manage MCLK we can now
use clk_get_rate() to determine if we need to divide MCLK without relying
on platform data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Request MCLK as a clock and then enable it when carrying out a state
transtion and while ANC is active, minimising system power consumption
in idle modes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The references used for the noise gates and parameters for their triggering
are configurable, expose that to users.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The references used for the noise gates and parameters for their triggering
are configurable, expose that to users.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Though the controls are named as stereo controls in the part the main use
case for the analogue inputs to the WM5102 is mono. Reflect this in the
controls exposed to userspace, providing a series of mono controls rather
than stereo ones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Though the controls are named as stereo controls in the part the main use
case for the analogue inputs to the WM5102 is mono. Reflect this in the
controls exposed to userspace, providing a series of mono controls rather
than stereo ones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the FLL is being shut down we will exit early so there is no need to
check here and in fact we're checking the wrong thing anyway.
Reported-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
sgtl5000 microphone gain only has 2 bits of resolution, so maximum value is 3.
From Eric Nelson:
"We also found that for the microphones we have here (commodity PC boom mics) a
default value of 2 for the gain gives the best results."
So change the default microphone gain as well.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Both the mask and mode settings are wrong in current code.
According to the datasheet:
S2PCFG0 (0x0A)
BIT[3:1] DATA_FORMAT
serial interface protocol format:
000: left Justified
001: I2S (default)
010: right justified
100: PCM no delay
101: PCM delay
111: DSP
Thus fixes the defines for LEFT_J_DATA_FORMAT, I2S_DATA_FORMAT, and
RIGHT_J_DATA_FORMAT.
Also adds define for DATA_FORMAT_MSK.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
