Sometimes a software reset is needed. Then some registers are saved and
restored but the interrupt mask register is missing. It causes issues
with sdio devices whose interrupts are masked after reset.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If the driver is loaded with a card in the slot, mmc_add_host() will
schedule an immediate card-detection work, which will start IO and wait
for command completion. Usually the kernel first returns to the sh_mmcif
probe function, lets it finish and only then schedules the rescan work.
But sometimes, expecially under heavy system load, the work will be
scheduled immediately before returning to the probe method. In this case
it is important for the driver to be fully prepared for IO. For sh_mmcif
this means, that also the timeout work has to be initialised before
calling mmc_add_host(). It is also better to prepare interrupts
beforehand. Besides, since mmc_add_host() does card-detection itself,
there is no need to do it again immediately afterwards.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
When DMA is in use and the card is ejected during IO, DMA transfers have to
be terminated, otherwise the dmaengine driver fails to operate properly,
when the card is re-inserted.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Found this issue during code review. Actually, there are two issues which
both compensate together in lucky case. In unlucky case the bus width
probing might not work as expected.
Signed-off-by: Jurgen Heeks <jurgen.heeks@nokia.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Modified the mmc_poweroff to resume before sending the poweroff
notification command. In sleep mode only AWAKE and RESET commands are
allowed, so before sending the poweroff notification command resume from
sleep mode and then send the notification command.
PowerOff Notify is tested on a Synopsis Designware Host Controller
(eMMC 4.5). The suspend to RAM and resume works fine.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Tested-by: Girish K S <girish.shivananjappa@linaro.org>
Reviewed-by: Saugata Das <saugata.das@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Set Medfield SDIO as non-removable to avoid un-necessary
card detect activity.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There is an understood mismatch between the voltage the host controller is
set to and the voltage supplied to the card by a fixed voltage regulator.
Teaching the driver to accept the mismatch is overly complicated. Instead
just accept the regulator's voltage.
This patch adds MMC_CAP2_BROKEN_VOLTAGE.
If the voltage didn't satisfy between min_uV and max_uV, try to change
the voltage in core.c. When changing the voltage, maybe use
regulator_set_voltage().
In regulator_set_voltage(), check the below condition.
/* sanity check */
if (!rdev->desc->ops->set_voltage &&
!rdev->desc->ops->set_voltage_sel) {
ret = -EINVAL;
goto out;
}
If some board should use the fixed-regulator, always return -EINVAL.
Then, eMMC didn't initialize always.
So if use a fixed-regulator, we need to add the MMC_CAP2_BROKEN_VOLTAGE.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When accessing the card on some FSL platform boards (e.g p2020, p1010,
mpc8536), the following error is reported with the timeout value calculated:
mmc0: Got data interrupt 0x00000020 even though no data operation was
in progress.
mmc0: Got data interrupt 0x00000020 even though no data operation was
in progress.
So we skip the calculation of timeout and use the max value to fix it.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Gao Guanhua <B22826@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For some FSL ESDHC controllers (e.g. P2020E, Rev1.0), the SDHC can not
work on DMA mode because of the hardware bug, so we set a broken dma flag
and use PIO mode.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Gao Guanhua <B22826@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ensure clocks are always enabled before any interaction with the
host controller driver. This makes sure that there is no race
between host execution and the core layer turning off clocks
in different context with clock gating framework.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The voltage_ranges is supposed to switch from big endian to little endian.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Chris Ball <cjb@laptop.org>
A UHS sdio card that fails initialization at 1.8v signaling is not in
UHS mode. We cannot use the speed in the the cis to reflect the bus
speed as this is the maxiumum value and will not reflect the fact
that the host is operating at a lower (non uhs) bus speed.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Reviewed-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When eSDHC module is enabled on P5020/P3041/P2041/P1010 with eSDHC
version 2.3, there is following errors:
mmc0: Timeout waiting for hardware interrupt.
mmc0: error -110 whilst initialising SD card
mmc0: Unexpected interrupt 0x02000000.
mmc0: Timeout waiting for hardware interrupt.
mmc0: error -110 whilst initialising SD card
mmc0: Unexpected interrupt 0x02000000.
It is because eSDHC controller has different bit setting for PROCTL
register at 0x28 comparing SD specification.
This patch sets DMAS bits correctly for byte operation and does not
change the default value of other field of PROCTL register.
For other FSL chips, such as MPC8536/P2020, PROCTL[DMAS]
bits are reserved and even if they are set to wrong bits, it will not
take effective.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Following removal announce and addition to feature-removal-schedule.txt,
here is the actual source code deletion for Atmel CAP9 family.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
MISC_DEVICES option alone does not select any kernel code and can cause dependency build warnings, such as:
warning: (KS8851 && AX88796_93CX6 && RTL8180 && RTL8187 && ADM8211 && RT2400PCI && RT2500PCI && RT61PCI && RT2800PCI && R8187SE) selects EEPROM_93CX6 which has unmet direct dependencies (MISC_DEVICES)
As the current drivers/misc/Kconfig stands, it is only possible to select the drivers below if MISC_DEVICES option is selected:
source "drivers/misc/c2port/Kconfig"
source "drivers/misc/eeprom/Kconfig"
source "drivers/misc/cb710/Kconfig"
source "drivers/misc/iwmc3200top/Kconfig"
source "drivers/misc/ti-st/Kconfig"
source "drivers/misc/lis3lv02d/Kconfig"
source "drivers/misc/carma/Kconfig"
source "drivers/misc/altera-stapl/Kconfig"
So remove MISC_DEVICES option so that nothing is dependant on it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the SDIO preparation to be done before the DMA job is setup.
This makes it possible to do DMA for SDIO transfers as well as the
earlier supported pio mode.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Added use of runtime PM autosuspend feature, with a fixed
timeout of 50 ms. This will prevent adding a latency,
although very minor, for _every_ request.
Moreover the runtime_get_sync is now also used in set_ios and
suspend since the runtime resourses are needed here as well.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The purpose of the vdd_handler does not make sense. We remove it
and use a generic approach instead. A new ios_handler is added, the
purpose of which e.g. can be to control GPIO pins to a levelshifter.
Previously the vdd_handler was also used for making additional
changes to the power register bits. This option is superfluous and is
therefore removed.
Adaptaptions from the old vdd_handler to the new ios_handler is done for
mach-ux500 board, which was the only one using the vdd_handler.
This patch is based upon a patch from Sebastian Rasmussen.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ST Micro variant supports bus signal direction indication. A new
member in the variant struct is added for this.
Moreover the actual signal direction configuration is board specific,
thus the amba mmci platform data is extended with a new member to be
able provide mmci with these specific board configurations.
This patch is based upon a patch from Sebastian Rasmussen.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch "mmc: core: move ->request() call from atomic context",
is the reason to why this change is possible. This simplifies the
error handling code execution path quite a lot and potentially also
fixes some error handling hang problems.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A significant increase (10-20%) in performance throughput for
USB mass storage is the reason for incrementing the value.
By some reason the USB driver allocates buffers which requires
a scattergather list to contain a lot more than 16 elements to
get optimal performance. This change sets the maximum elements
to 128.
Tests with large reads and large writes (100 MiB) show that the
throughput increase is significant for write (10% for this test)
but not for read. Tests are run on a Linux host with ext4 FS on
the gadget mass storage device. The sg-len still exceeds 16 for
the read tests but the performance gain is low or nothing.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Autogenerated GPG tag for Rusty D1ADB8F1: 15EE 8D6C AB0E 7F0C F999 BFCB D920 0E6C D1AD B8F1
* tag 'for-linus' of git://github.com/rustyrussell/linux:
module_param: check that bool parameters really are bool.
intelfbdrv.c: bailearly is an int module_param
paride/pcd: fix bool verbose module parameter.
module_param: make bool parameters really bool (drivers & misc)
module_param: make bool parameters really bool (arch)
module_param: make bool parameters really bool (core code)
kernel/async: remove redundant declaration.
printk: fix unnecessary module_param_name.
lirc_parallel: fix module parameter description.
module_param: avoid bool abuse, add bint for special cases.
module_param: check type correctness for module_param_array
modpost: use linker section to generate table.
modpost: use a table rather than a giant if/else statement.
modules: sysfs - export: taint, coresize, initsize
kernel/params: replace DEBUGP with pr_debug
module: replace DEBUGP with pr_debug
module: struct module_ref should contains long fields
module: Fix performance regression on modules with large symbol tables
module: Add comments describing how the "strmap" logic works
Fix up conflicts in scripts/mod/file2alias.c due to the new linker-
generated table approach to adding __mod_*_device_table entries. The
ARM sa11x0 mcp bus needed to be converted to that too.
MMC highlights for 3.3:
Core:
* Support for the HS200 high-speed eMMC mode.
* Support SDIO 3.0 Ultra High Speed cards.
* Kill pending block requests immediately if card is removed.
* Enable the eMMC feature for locking boot partitions read-only
until next power on, exposed via sysfs.
Drivers:
* Runtime PM support for Intel Medfield SDIO.
* Suspend/resume support for sdhci-spear.
* sh-mmcif now processes requests asynchronously.
* tag 'mmc-merge-for-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (58 commits)
mmc: fix a deadlock between system suspend and MMC block IO
mmc: sdhci: restore the enabled dma when do reset all
mmc: dw_mmc: miscaculated the fifo-depth with wrong bit operation
mmc: host: Adds support for eMMC 4.5 HS200 mode
mmc: core: HS200 mode support for eMMC 4.5
mmc: dw_mmc: fixed wrong bit operation for SDMMC_GET_FCNT()
mmc: core: Separate the timeout value for cache-ctrl
mmc: sdhci-spear: Fix compilation error
mmc: sdhci: Deal with failure case in sdhci_suspend_host
mmc: dw_mmc: Clear the DDR mode for non-DDR
mmc: sd: Fix SDR12 timing regression
mmc: sdhci: Fix tuning timer incorrect setting when suspending host
mmc: core: Add option to prevent eMMC sleep command
mmc: omap_hsmmc: use threaded irq handler for card-detect.
mmc: sdhci-pci: enable runtime PM for Medfield SDIO
mmc: sdhci: Always pass clock request value zero to set_clock host op
mmc: sdhci-pci: remove SDHCI_QUIRK2_OWN_CARD_DETECTION
mmc: sdhci-pci: get gpio numbers from platform data
mmc: sdhci-pci: add platform data
mmc: sdhci: prevent card detection activity for non-removable cards
...
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Performing MMC block IO with simultaneous STR can lead to a deadlock: the
mmc_pm_notify() function claims the host and then calls bus .remove()
method, which lands in mmc_blk_remove(), which calls mmc_blk_remove_req()
then it goes to -> mmc_cleanup_queue() -> kthread_stop(), which waits for
the mmc-block thread to stop. If the mmc-block thread at that time is
processing block requests, it will also try to claim the host in
mmc_blk_issue_rq() and block there. This patch fixes the problem by
calling .remove() before claiming the host.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If dma is enabled, it'll be cleared when reset all is performed, this can
be observed on some platforms, such as P2041 which has a version 2.3
controller, but platform like P4080 which has a version 2.2 controller,
does not suffer this, so we will check if the dma is enabled, we should
restore it after reset all.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In FIFOTH register, the RX_WMark field (bits[27:16]) defaults to
FIFO_DEPTH - 1. When reading it, bits[26:16] were being used, so
fix it to use the mask 0xfff instead of 0x7ff.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for the HS200 mode on the host side.
Also enables the tuning feature required when the HS200 mode
is selected.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds the support of the HS200 bus speed for eMMC 4.5 devices.
The eMMC 4.5 devices have support for 200MHz bus speed. The function
prototype of the tuning function is modified to handle the tuning
command number which is different in sd and mmc case.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Turning the cache off implies flushing cache which doesn't define
maximum timeout unlike cache-on. This patch will apply the generic
CMD6 timeout only for cache-on. Additionally the kernel message is
added for checking failure case of cache-on.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
With the inclusion of following patch (59b5bc3929b37):
"mmc: sdhci: remove "state" argument from sdhci_suspend_host"
we get a compilation error for sdhci-spear:
drivers/mmc/host/sdhci-spear.c:283:2: error: too many arguments to function
‘sdhci_suspend_host’
This patch fixes this error.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
If there are errors happened in sdhci_suspend_host, handle it so that
when the function returns with an error, the host's behaviour is the
same before this function call, e.g. card detection is enabled and
tuning timer is active, etc.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
UHS_REG should be cleared for non-DDR mode. But currently there is
no way to clear DDR mode, if it is already set once. This patch adds
clearing DDR mode for non-DDR mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes a failure to recognize SD cards reported on a Dell
Vostro with O2 Micro SD card reader. Patch 49c468f ("mmc: sd: add
support for uhs bus speed mode selection") caused the problem, by
setting the SDHCI_CTRL_HISPD flag even for legacy timings.
Signed-off-by: Alexander Elbs <alex@segv.de>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Arindam Nath <arindam.nath@amd.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
