Configure the mac address in add_interface and clear it in
remove_interface so that users can change the mac address
to something other than the one in the eeprom. Also avoid
setting it at attach time so that we won't ack packets
until fully set up.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CHANNEL_CCK flag is set for all 2 Ghz channels, so IS_CHAN_CCK() would
turn out to be true for all channles in that band.
Use IS_CHAN_B() now, which checks the channel mode and not the channel
flags.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, use a helper function to setup RC status data
when processing completed TX descriptors.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace TRUE/FALSE macros with VALID/INVALID macros.
Follow a consistent variable convention.
Remove unnecessary comments.
Add all RC phy macros into a single enum.
Merge functions into reasonably sized entities.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Maintaining two sets of rate tables is redundant, remove one
and use struct ath_rate_table exclusively.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the hack using vif, and use rate_driver_data within
skb->cb to hold driver specific rate information.
Setup the rate series in the skb's tx control area and remove
all references to ath9k specific rate series ( using struct ath_rc_series ).
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the hw rate tables to ath_softc, and access them directly.
tx_triglevel_max is global, move it to ath_rate_node.
Now that ath_rate_softc is gone, rate control attach becomes simpler.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rate control init is now confined to itself, using the
HT capabilites of the STA from rate_init().
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove a lot of old, crufty code and make
RX status reporting a bit sane and clean.
Do not do anything to the RX skb before unmapping.
So in ath_rx_tasklet(), move the skb_put() after PCI unmap.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces __builtin_return_address(0) with _RET_IP_, since a
previous patch moved _RET_IP_ and _THIS_IP_ to include/linux/kernel.h and
they're widely available now. This makes for shorter and easier to read
code.
[penberg@cs.helsinki.fi: remove _RET_IP_ casts to void pointer]
Signed-off-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
In the commit entitled "mac80211/drivers: rewrite the rate control
API", the meaning of the packet transmit count was changed from the
number of retries to the total number. In driver rtl8187, this change
was missed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit 9ea2c74 named "mac80211/drivers: rewrite the rate control API",
the meaning of status.rates[i].count was changed from number of retries
to total number of tries. As a result, the pid rate-setting algorithm fails
because every packet appears to have needed a retransmit.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we switch off the LEDS during initialization
we kill rt73usb from proper functioning. The immediate
result after the first LED command are MCU failures
and a complete breakdown of TX/RX.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since WE7 /proc/net/wireless checks whether level and noise are in dBm
and shows them accordingly. Indicate that we return signal and noice
levels in dBm.
Before:
Inter-| sta-| Quality | Discarded packets | Missed | WE
face | tus | link level noise | nwid crypt frag retry misc | beacon | 22
eth1: 0000 65. 219. 165. 0 0 148 41 0 0
After:
Inter-| sta-| Quality | Discarded packets | Missed | WE
face | tus | link level noise | nwid crypt frag retry misc | beacon | 22
eth1: 0000 65. -37. -91. 0 0 0 0 0 0
While at it, replace raw numbers with appropriate macro.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add asl, pzl and di debugfs files to uwb/uwbN/wusbhc for WHCI host
controller. These dump the current ASL, PZL and DI buffer.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Mathieu Desnoyers reported this build failure on powerpc:
kernel/sched.c: In function 'sd_init_NODE':
kernel/sched.c:7319: error: non-static initialization of a flexible array member
kernel/sched.c:7319: error: (near initialization for '(anonymous)')
this happens because .span changed to cpumask_var_t, hence
the static CPU_MASK_NONE initializers in the SD_*_INIT
templates are not type-correct anymore.
Remove them, as they default to empty anyway.
Also remove them from IA64, MIPS and SH.
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With the callback mode HRTIMER_CB_IRQSAFE_UNLOCK, the start of the
stream with zero delay doesn't work. Since IRQSAFE mode is removed,
we have to change the pcsp start-up code.
This patch splits the callback function to two parts, the triggering
of the port and the calculation of the expire time, and the update of
the ALSA PCM core. The first part is called both from the trigger-start
and the hrtimer callback while the latter is handled only in the
hrtimer callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Port to the new tracepoints API: split DEFINE_TRACE() and DECLARE_TRACE()
sites. Spread them out to the usage sites, as suggested by
Mathieu Desnoyers.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
The previous fix for the conntrack creation race (netfilter: ctnetlink:
fix conntrack creation race) missed a GFP_KERNEL allocation that is
now performed while holding a spinlock. Switch to GFP_ATOMIC.
Reported-and-tested-by: Zoltan Borbely <bozo@andrews.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was a forward port of work done by Mathieu Desnoyers, I changed it to
encode the 'what' parameter on the tracepoint name, so that one can register
interest in specific events and not on classes of events to then check the
'what' parameter.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It is possible for a shadow page to have a parent link
pointing to a freed page. When zapping a high level table,
kvm_mmu_page_unlink_children fails to remove the parent_pte link.
For that to happen, the child must be unreachable via the shadow
tree, which can happen in shadow_walk_entry if the guest pte was
modified in between walk() and fetch(). Remove the parent pte
reference in such case.
Possible cause for oops in bug #2217430.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
physmap_flash_remove releases only last memory region. This causes
memory leak if multiple resources were provided.
This patch fixes this leakage by using devm_ functions.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fixes broken terminology added in the "m25p80.c erase enhance" patch,
which added a chip erase command but called it "block erase". There are
already two block erase commands; blocks are 4KiB or 32KiB. There's also
a sector erase (usually 64 KiB). Chip erase typically covers Megabytes.
OPCODE_BE ==> OPCODE_CHIP_ERASE
erase_block ==> erase_chip
[dbrownell@users.sourceforge.net: update sector erase comments too ]
Signed-off-by: Chen Gong <clumsycg@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit d0e8c47c58 ("m25p80.c extended jedec
support") added support for extended ids but seems to break on flashes
which don't have an extended id defined. If the table does not have an
extid defined, then we should ignore it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit d0e8c47c58 ("m25p80.c extended jedec
support") added support for extended ids but in the process managed to
break detection of all flashes.
The ext jedec id check was inserted into an if statement that lacked
braces, and it did not add the required braces. As such, the detection
routine always returns the first entry in the SPI flash list.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When queuing a skb to sk->sk_receive_queue, we can release its dst,
not anymore needed. Since current cpu did the dst_hold(), refcount is
probably still hot int this cpu caches.
This avoids readers to access the original dst to decrement its
refcount, possibly a long time after packet reception. This should
speedup UDP and RAW receive path.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: add .config driven boot parameter default value
Right now debugobjects can only be activated if the debug_objects
boot parameter is passed in via the boot command line.
Make this more convenient (and randomizable) by also providing
a .config method. Enable it by default. (DEBUG_OBJECTS itself
is default-off)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: make global variables and a function static
Fix following sparse warnings:
arch/x86/kernel/microcode_core.c:102:22: warning: symbol
'microcode_ops' was not declared. Should it be static?
arch/x86/kernel/microcode_core.c:206:24: warning: symbol
'microcode_pdev' was not declared. Should it be static?
arch/x86/kernel/microcode_core.c:322:6: warning: symbol
'microcode_update_cpu' was not declared. Should it be static?
arch/x86/kernel/microcode_intel.c:468:22: warning: symbol
'microcode_intel_ops' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
