[ Upstream commit 11a39259ff79b74bc99f8b7c44075a2d6d5e7ab1 ]
bnxt_half_open_nic() is called during during ethtool self test and is
protected by rtnl_lock. Firmware reset can be happening at the same
time. Only critical portions of the entire firmware reset sequence
are protected by the rtnl_lock. It is possible that bnxt_half_open_nic()
can be called when the firmware reset sequence is aborting. In that
case, bnxt_half_open_nic() needs to check if the ABORT_ERR flag is set
and abort if it is. The ethtool self test will fail but the NIC will be
brought to a consistent IF_DOWN state.
Without this patch, if bnxt_half_open_nic() were to continue in this
error state, it may crash like this:
bnxt_en 0000:82:00.1 enp130s0f1np1: FW reset in progress during close, FW reset will be aborted
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
...
Process ethtool (pid: 333327, stack limit = 0x0000000046476577)
Call trace:
bnxt_alloc_mem+0x444/0xef0 [bnxt_en]
bnxt_half_open_nic+0x24/0xb8 [bnxt_en]
bnxt_self_test+0x2dc/0x390 [bnxt_en]
ethtool_self_test+0xe0/0x1f8
dev_ethtool+0x1744/0x22d0
dev_ioctl+0x190/0x3e0
sock_ioctl+0x238/0x480
do_vfs_ioctl+0xc4/0x758
ksys_ioctl+0x84/0xb8
__arm64_sys_ioctl+0x28/0x38
el0_svc_handler+0xb0/0x180
el0_svc+0x8/0xc
Fixes: a1301f08c5 ("bnxt_en: Check abort error state in bnxt_open_nic().")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96bdd4b9ea7ef9a12db8fdd0ce90e37dffbd3703 ]
Only pass supported VLAN protocol IDs for stripped VLAN tags to the
stack. The stack will hit WARN() if the protocol ID is unsupported.
Existing firmware sets up the chip to strip 0x8100, 0x88a8, 0x9100.
Only the 1st two protocols are supported by the kernel.
Fixes: a196e96bb6 ("bnxt_en: clean up VLAN feature bit handling")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6cd657cb3ee6f4de57e635b126ffbe0e51d00f1a ]
In the BNXT_FW_RESET_STATE_POLL_VF state in bnxt_fw_reset_task() after all
VFs have unregistered, we need to check for BNXT_STATE_ABORT_ERR after
we acquire the rtnl_lock. If the flag is set, we need to abort.
Fixes: 230d1f0de7 ("bnxt_en: Handle firmware reset.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c9f046bc377efd1f5e26e74817d5f96e9506c86 ]
The capabilities can change after firmware upgrade/downgrade, so we
should get the up-to-date RoCE capabilities everytime bnxt_ulp_probe()
is called.
Fixes: 2151fe0830 ("bnxt_en: Handle RESET_NOTIFY async event from firmware.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c81cfb6256d90ea5ba4a6fb280ea3b171be4e05c ]
If device is already disabled in reset path and PCI io error is
detected before the device could be enabled, driver could
call pci_disable_device() for already disabled device. Fix this
problem by calling pci_disable_device() only if the device is already
enabled.
Fixes: 6316ea6db9 ("bnxt_en: Enable AER support.")
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2b452550a203d88112eaf0ba9fc4b750a000b496 upstream.
Make sure that we disable each of the TX and RX queues in the TDMA and
RDMA control registers. This is a correctness change to be symmetrical
with the code that enables the TX and RX queues.
Tested-by: Maxime Ripard <maxime@cerno.tech>
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a3c680aa2c12c90c44af383fe6882a39875ab81 upstream.
Setting the EXT_ENERGY_DET_MASK bit allows the port energy detection
logic of the internal PHY to prevent the system from sleeping. Some
internal PHYs will report that energy is detected when the network
interface is closed which can prevent the system from going to sleep
if WoL is enabled when the interface is brought down.
Since the driver does not support waking the system on this logic,
this commit clears the bit whenever the internal PHY is powered up
and the other logic for manipulating the bit is removed since it
serves no useful function.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 74325bf0104573c6dfce42837139aeef3f34be76 ]
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2ac9800cfe0f8da16abc4e74e003440361c112e ]
The Broadcom UniMAC MDIO bus from mdio-bcm-unimac module comes too late.
So, GENET cannot find the ethernet PHY on UniMAC MDIO bus. This leads
GENET fail to attach the PHY as following log:
bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000
...
could not attach to PHY
bcmgenet fd580000.ethernet eth0: failed to connect to PHY
uart-pl011 fe201000.serial: no DMA platform data
libphy: bcmgenet MII bus: probed
...
unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus
This patch adds the soft dependency to load mdio-bcm-unimac module
before genet module to avoid the issue.
Fixes: 9a4e796970 ("net: bcmgenet: utilize generic Broadcom UniMAC MDIO controller driver")
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=213485
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03400aaa69f916a376e11526cf591901a96a3a5c ]
bnxt_ethtool_init() may have allocated some memory and we need to
call bnxt_ethtool_free() to properly unwind if bnxt_init_one()
fails.
Fixes: 7c38091814 ("bnxt_en: Refactor bnxt_init_one() and turn on TPA support on 57500 chips.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c12e1643d2738bcd4e26252ce531878841dd3f38 ]
TQM fastpath ring needs to be sized to store both the requester
and responder side of RoCE QPs in TQM for supporting bi-directional
tests. Fix bnxt_alloc_ctx_mem() to multiply the RoCE QPs by a factor of
2 when computing the number of entries for TQM fastpath ring. This
fixes an RX pipeline stall issue when running bi-directional max
RoCE QP tests.
Fixes: c7dd7ab4b2 ("bnxt_en: Improve TQM ring context memory sizing formulas.")
Signed-off-by: Rukhsana Ansari <rukhsana.ansari@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0afd6a4e8028cc487c240b6cfe04094e45a306e4 ]
There is a missing bnxt_probe_phy() call in bnxt_fw_init_one() to
rediscover the PHY capabilities after a firmware reset. This can cause
some PHY related functionalities to fail after a firmware reset. For
example, in multi-host, the ability for any host to configure the PHY
settings may be lost after a firmware reset.
Fixes: ec5d31e3c1 ("bnxt_en: Handle firmware reset status during IF_UP.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 702279d2ce4650000bb6302013630304e359dc13 ]
There was a typo in the code that checks for 64K BNXT_PAGE_SHIFT in
bnxt_hwrm_set_pg_attr(). Fix it and make the code more understandable
with a new macro BNXT_SET_CTX_PAGE_ATTR().
Fixes: 1b9394e5a2 ("bnxt_en: Configure context memory on new devices.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab21494be9dc7d62736c5fcd06be65d49df713ee ]
Otherwise, some of the recently added HyperV VF IDs would not be
recognized as VF devices and they would not initialize properly.
Fixes: 7fbf359bb2c1 ("bnxt_en: Add PCI IDs for Hyper-V VF devices.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28c66b6da4087b8cfe81c2ec0a46eb6116dafda9 ]
Fix to return -EPERM from the error handling case instead of 0, as done
elsewhere in this function.
Fixes: b6016b7673 ("[BNX2]: New Broadcom gigabit network driver.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbd6f0a948139970f4a615dff189d9a503681a39 ]
In bnxt_rx_pkt(), the RX buffers are expected to complete in order.
If the RX consumer index indicates an out of order buffer completion,
it means we are hitting a hardware bug and the driver will abort all
remaining RX packets and reset the RX ring. The RX consumer index
that we pass to bnxt_discard_rx() is not correct. We should be
passing the current index (tmp_raw_cons) instead of the old index
(raw_cons). This bug can cause us to be at the wrong index when
trying to abort the next RX packet. It can crash like this:
#0 [ffff9bbcdf5c39a8] machine_kexec at ffffffff9b05e007
#1 [ffff9bbcdf5c3a00] __crash_kexec at ffffffff9b111232
#2 [ffff9bbcdf5c3ad0] panic at ffffffff9b07d61e
#3 [ffff9bbcdf5c3b50] oops_end at ffffffff9b030978
#4 [ffff9bbcdf5c3b78] no_context at ffffffff9b06aaf0
#5 [ffff9bbcdf5c3bd8] __bad_area_nosemaphore at ffffffff9b06ae2e
#6 [ffff9bbcdf5c3c28] bad_area_nosemaphore at ffffffff9b06af24
#7 [ffff9bbcdf5c3c38] __do_page_fault at ffffffff9b06b67e
#8 [ffff9bbcdf5c3cb0] do_page_fault at ffffffff9b06bb12
#9 [ffff9bbcdf5c3ce0] page_fault at ffffffff9bc015c5
[exception RIP: bnxt_rx_pkt+237]
RIP: ffffffffc0259cdd RSP: ffff9bbcdf5c3d98 RFLAGS: 00010213
RAX: 000000005dd8097f RBX: ffff9ba4cb11b7e0 RCX: ffffa923cf6e9000
RDX: 0000000000000fff RSI: 0000000000000627 RDI: 0000000000001000
RBP: ffff9bbcdf5c3e60 R8: 0000000000420003 R9: 000000000000020d
R10: ffffa923cf6ec138 R11: ffff9bbcdf5c3e83 R12: ffff9ba4d6f928c0
R13: ffff9ba4cac28080 R14: ffff9ba4cb11b7f0 R15: ffff9ba4d5a30000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
Fixes: a1b0e4e684 ("bnxt_en: Improve RX consumer index validity check.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27537929f30d3136a71ef29db56127a33c92dad7 ]
The problem is that bnxt_show_temp() returns long but "rc" is an int
and "len" is a u32. With ternary operations the type promotion is quite
tricky. The negative "rc" is first promoted to u32 and then to long so
it ends up being a high positive value instead of a a negative as we
intended.
Fix this by removing the ternary.
Fixes: d69753fa1e ("bnxt_en: return proper error codes in bnxt_show_temp")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 20d7d1c5c9b11e9f538ed4a2289be106de970d3e upstream.
The following trace excerpt corresponds with a NULL pointer dereference
of 'bp->irq_tbl' in bnxt_setup_inta() on an Aarch64 system after many
device resets:
Unable to handle kernel NULL pointer dereference at ... 000000d
...
pc : string+0x3c/0x80
lr : vsnprintf+0x294/0x7e0
sp : ffff00000f61ba70 pstate : 20000145
x29: ffff00000f61ba70 x28: 000000000000000d
x27: ffff0000009c8b5a x26: ffff00000f61bb80
x25: ffff0000009c8b5a x24: 0000000000000012
x23: 00000000ffffffe0 x22: ffff000008990428
x21: ffff00000f61bb80 x20: 000000000000000d
x19: 000000000000001f x18: 0000000000000000
x17: 0000000000000000 x16: ffff800b6d0fb400
x15: 0000000000000000 x14: ffff800b7fe31ae8
x13: 00001ed16472c920 x12: ffff000008c6b1c9
x11: ffff000008cf0580 x10: ffff00000f61bb80
x9 : 00000000ffffffd8 x8 : 000000000000000c
x7 : ffff800b684b8000 x6 : 0000000000000000
x5 : 0000000000000065 x4 : 0000000000000001
x3 : ffff0a00ffffff04 x2 : 000000000000001f
x1 : 0000000000000000 x0 : 000000000000000d
Call trace:
string+0x3c/0x80
vsnprintf+0x294/0x7e0
snprintf+0x44/0x50
__bnxt_open_nic+0x34c/0x928 [bnxt_en]
bnxt_open+0xe8/0x238 [bnxt_en]
__dev_open+0xbc/0x130
__dev_change_flags+0x12c/0x168
dev_change_flags+0x20/0x60
...
Ordinarily, a call to bnxt_setup_inta() (not in trace due to inlining)
would not be expected on a system supporting MSIX at all. However, if
bnxt_init_int_mode() does not end up being called after the call to
bnxt_clear_int_mode() in bnxt_fw_reset_close(), then the driver will
think that only INTA is supported and bp->irq_tbl will be NULL,
causing the above crash.
In the error recovery scenario, we call bnxt_clear_int_mode() in
bnxt_fw_reset_close() early in the sequence. Ordinarily, we will
call bnxt_init_int_mode() in bnxt_hwrm_if_change() after we
reestablish communication with the firmware after reset. However,
if the sequence has to abort before we call bnxt_init_int_mode() and
if the user later attempts to re-open the device, then it will cause
the crash above.
We fix it in 2 ways:
1. Check for bp->irq_tbl in bnxt_setup_int_mode(). If it is NULL, call
bnxt_init_init_mode().
2. If we need to abort in bnxt_hwrm_if_change() and cannot complete
the error recovery sequence, set the BNXT_STATE_ABORT_ERR flag. This
will cause more drastic recovery at the next attempt to re-open the
device, including a call to bnxt_init_int_mode().
Fixes: 3bc7d4a352 ("bnxt_en: Add BNXT_STATE_IN_FW_RESET state.")
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit db28b6c77f4050f62599267a886b61fbd6504633 ]
The running fw.psid version is in decimal format but the stored
fw.psid is in hex format. This can mislead the user to reset the
NIC to activate the stored version to become the running version.
Fix it to display the stored fw.psid in decimal format.
Fixes: 1388875b39 ("bnxt_en: Add stored FW version info to devlink info_get cb.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 132e0b65dc2b8bfa9721bfce834191f24fd1d7ed ]
A TX queue can potentially immediately timeout after it is stopped
and the last TX timestamp on that queue was more than 5 seconds ago with
carrier still up. Prevent these intermittent false TX timeouts
by bringing down carrier first before calling netif_tx_disable().
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 869c4d5eb1e6fbda66aa790c48bdb946d71494a0 upstream.
The function bnxt_get_ulp_stat_ctxs() does not count the stats contexts
used by the RDMA driver correctly when the RDMA driver is freeing the
MSIX vectors. It assumes that if the RDMA driver is registered, the
additional stats contexts will be needed. This is not true when the
RDMA driver is about to unregister and frees the MSIX vectors.
This slight error leads to over accouting of the stats contexts needed
after the RDMA driver has unloaded. This will cause some firmware
warning and error messages in dmesg during subsequent config. changes
or ifdown/ifup.
Fix it by properly accouting for extra stats contexts only if the
RDMA driver is registered and MSIX vectors have been successfully
requested.
Fixes: c027c6b4e9 ("bnxt_en: get rid of num_stat_ctxs variable")
Reviewed-by: Yongping Zhang <yongping.zhang@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fb1e6e562b37b39adfe251919c9abfdb3e01f921 ]
A recent change skips sending firmware messages to the firmware when
pci_channel_offline() is true during fatal AER error. To make this
complete, we need to move the re-initialization sequence to
bnxt_io_resume(), otherwise the firmware messages to re-initialize
will all be skipped. In any case, it is more correct to re-initialize
in bnxt_io_resume().
Also, fix the reverse x-mas tree format when defining variables
in bnxt_io_slot_reset().
Fixes: b340dc680e ("bnxt_en: Avoid sending firmware messages when AER error is detected.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a029a2fef5d11bb85587433c3783615442abac96 ]
TQM rings are hardware resources that require host context memory
managed by the driver. The driver supports up to 9 TQM rings and
the number of rings to use is requested by firmware during run-time.
Cap this number to the maximum supported to prevent accessing beyond
the array. Future firmware may request more than 9 TQM rings. Define
macros to remove the magic number 9 from the C code.
Fixes: ac3158cb01 ("bnxt_en: Allocate TQM ring context memory according to fw specification.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VFs do not have access permissions to issue NVM_GET_DEV_INFO
firmware command.
Fixes: 4933f6753b ("bnxt_en: Add bnxt_hwrm_nvm_get_dev_info() to query NVM info.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bnxt_add_one_ctr() adds a hardware counter to a software counter and
adjusts for the hardware counter wraparound against the mask. The logic
assumes that the hardware counter is always smaller than or equal to
the mask.
This assumption is mostly correct. But in some cases if the firmware
is older and does not provide the accurate mask, the driver can use
a mask that is smaller than the actual hardware mask. This can cause
some extra carry bits to be added to the software counter, resulting in
counters that far exceed the actual value. Fix it by masking the
hardware counter with the mask passed into bnxt_add_one_ctr().
Fixes: fea6b33355 ("bnxt_en: Accumulate all counters.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Firmware is unable to retain the port counters during any kind of
fatal or non-fatal resets, so we must clear the port counters to
avoid false detection of port counter overflow.
Fixes: fea6b33355 ("bnxt_en: Accumulate all counters.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The module eeprom address range returned by bnxt_get_module_eeprom()
should be 256 bytes of A0h address space, the lower half of the A2h
address space, and page 0 for the upper half of the A2h address space.
Fix the firmware call by passing page_number 0 for the A2h slave address
space.
Fixes: 42ee18fe4c ("bnxt_en: Add Support for ETHTOOL_GMODULEINFO and ETHTOOL_GMODULEEEPRO")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the AER or firmware reset flow, if we are in fatal error state or
if pci_channel_offline() is true, we don't send any commands to the
firmware because the commands will likely not reach the firmware and
most commands don't matter much because the firmware is likely to be
reset imminently.
However, the HWRM_FUNC_RESET command is different and we should always
attempt to send it. In the AER flow for example, the .slot_reset()
call will trigger this fw command and we need to try to send it to
effect the proper reset.
Fixes: b340dc680e ("bnxt_en: Avoid sending firmware messages when AER error is detected.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a PCIe fatal error occurs, the internal latched BAR addresses
in the chip get reset even though the BAR register values in config
space are retained.
pci_restore_state() will not rewrite the BAR addresses if the
BAR address values are valid, causing the chip's internal BAR addresses
to stay invalid. So we need to zero the BAR registers during PCIe fatal
error to force pci_restore_state() to restore the BAR addresses. These
write cycles to the BAR registers will cause the proper BAR addresses to
latch internally.
Fixes: 6316ea6db9 ("bnxt_en: Enable AER support.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As part of the commit b148bb238c
("bnxt_en: Fix possible crash in bnxt_fw_reset_task()."),
cancel_delayed_work_sync() is called only for VFs to fix a possible
crash by cancelling any pending delayed work items. It was assumed
by mistake that the flush_workqueue() call on the PF would flush
delayed work items as well.
As flush_workqueue() does not cancel the delayed workqueue, extend
the fix for PFs. This fix will avoid the system crash, if there are
any pending delayed work items in fw_reset_task() during driver's
.remove() call.
Unify the workqueue cleanup logic for both PF and VF by calling
cancel_work_sync() and cancel_delayed_work_sync() directly in
bnxt_remove_one().
Fixes: b148bb238c ("bnxt_en: Fix possible crash in bnxt_fw_reset_task().")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A recent patch has moved the workqueue cleanup logic before
calling unregister_netdev() in bnxt_remove_one(). This caused a
regression because the workqueue can be restarted if the device is
still open. Workqueue cleanup must be done after unregister_netdev().
The workqueue will not restart itself after the device is closed.
Call bnxt_cancel_sp_work() after unregister_netdev() and
call bnxt_dl_fw_reporters_destroy() after that. This fixes the
regession and the original NULL ptr dereference issue.
Fixes: b16939b59c ("bnxt_en: Fix NULL ptr dereference crash in bnxt_fw_reset_task()")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds FW versions stored in the flash to devlink info_get
callback. Return the correct fw.psid running version using the
newly added bp->nvm_cfg_ver.
v2:
Ensure stored pkg_name string is NULL terminated when copied to
devlink.
Return directly from the last call to bnxt_dl_info_put().
If the FW call to get stored version fails for any reason, return
success immediately to devlink without the stored versions.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-10-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
