The hardware I/O has to be open-coded due to registers of unequal sizes.
Other than that, the transition is straight forward.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ADAU1701 has 2 hardware pins to configure the PLL mode in accordance
to the MCLK-to-LRCLK ratio. These pins have to be stable before the chip
is released from reset, and a full reset cycle, including a new firmware
download is needed whenever they change.
This patch adds GPIO properties to the DT bindings of the Codec, and
implements makes the set_sysclk memorize the configured sysclk.
Because the run-time parameters are unknown at probe time, the first
firmware download is postponed to the first hw_params call, when the
driver can determine the mclk/lrclk divider. Subsequent downloads
are only issued when the divider configuration changes.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The chip needs a new download after each reset, so the code to do that
needs to live in adau1701_reset().
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The TAS5086 has two alternative modes to start its PWM channels, Mid-Z
and Low-Z. Which one to use depends on how the PWM power stages are
connected to the TAS5086.
This patch adds 6 optional boolean properties to the DT bindings of the
driver which allow the user to configure each individual channel to the
Mid-Z scheme, and leaves all the others to the default (Low-Z).
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The TAS5086 has two muxes, one for connecting I2S inputs to internal
channels, and another one for selecting which internal channel should
be routed to which PWM output pin.
This patch adds DAPM widgets and routes for this driver.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add register definitions for input and output mux registers, and rewrite
the tas5086_accessible_reg() function.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to support registers of unequal sizes, the I2C I/O has to be
open-coded.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
To reduce pop noise during playback stream start and stop the codec needs
to have the digital_mute callback implemented.
The codec need to be muted before the CPU dai has been stopped (McPDM).
Stopping the McPDM will generate a pop on the codec since no signal on the
PDM bus means full negative amplitude.
By managing the mute/unmute state of the outputs we can decrease the amount
of pop noise when playback starts or stops.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We need to free the irq at twl6040_remove() which is called when the machine
driver has been removed (the card has been removed).
If we fail to do that, next time when the machine driver is loaded the
codec's probe will fail since the irq has been already requested.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This part of bias settings are essential for WM8962 to power up. Without it
"wm8962 0-001a: DC servo timed out" might be prompted due to power-up failure
that happens to FLL if being used.
The driver's also bringing the bias down in the suspend path so it needs to be
powered up in the resume path for symmetry.
According to dapm_pre_sequence_async(), DAPM would call pm_runtime_get_sync()
to let driver finish the bias settings in pm_runtime_resume() before the bias
level being set to STANDBY. So no need to worry about disordered settings for
VMID of WM8962.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This fixes:
975:9: sparse: Using plain integer as NULL pointer
1917:24: sparse: symbol 'rt5640_aif_dai_ops' was not declared. Should it be static?
1924:27: sparse: symbol 'rt5640_dai' was not declared. Should it be static?
2079:19: sparse: symbol 'rt5640_i2c_driver' was not declared. Should it be static?
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Modify the RT5640 driver to parse platform data from device tree. Write
a DT binding document to describe those properties.
Slight re-ordering of rt5640_i2c_probe() to better fit the DT parsing.
Since ldo1_en is optional, guard usage of it with gpio_is_valid(), rather
than open-coding an if (gpio) check.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver is useless if both SPI and I2C are not configured.
Thus don't build this driver if both SPI and I2C are not configured.
This patch silences below build warning if both SPI and I2C are not configured.
CC sound/soc/codecs/adav80x.o
sound/soc/codecs/adav80x.c:842:12: warning: 'adav80x_bus_probe' defined but not used [-Wunused-function]
sound/soc/codecs/adav80x.c:863:12: warning: 'adav80x_bus_remove' defined but not used [-Wunused-function]
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
