The clock output on imx6q CCM_CLKO1 pad is not always cko1 clock, and
there is a multiplexer to select between cko1 and cko2. Add this
missing selection as the clock cko.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The patch add basic support for the quad spi controller.
QSPI is a kind of spi module that allows single,
dual and quad read access to external spi devices. The module
has a memory mapped interface which provide direct interface
for accessing data form external spi devices.
The patch will configure controller clocks, device control
register and for defining low level transfer apis which
will be used by the spi framework to transfer data to
the slave spi device(flash in this case).
Test details:
-------------
Tested this on dra7 board.
Test1: Ran mtd_stesstest for 40000 iterations.
- All iterations went through without failure.
Test2: Use mtd utilities:
- flash_erase to erase the flash device
- mtd_debug read to read data back.
- mtd_debug write to write to the data flash.
diff between the write and read data shows zero.
Acked-by: Felipe Balbi<balbi@ti.com>
Reviewed-by: Felipe Balbi<balbi@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the document for DSPI driver under
Documentation/devicetree/bindings/spi/.
Signed-off-by: Chao Fu <b44548@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds ac97-slave support.
For ac97, the registers have to be setup earlier than for other ssi
modes because there is some communication with the external device
before streaming. So this patch introduces a fsl_ssi_setup function to
setup the registers for different ssi operation modes seperately.
This patch was tested with imx27-pca100.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch implements a device-tree-only CPU DAI driver for Freescale
S/PDIF controller that supports stereo playback and record feature.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Allwinner sunXi core additions for 3.12, take 2
These patches add machine support for the Allwinner A20 and A31 SoCs
* tag 'sunxi-core-for-3.12-2' of https://github.com/mripard/linux:
ARM: sunxi: Introduce Allwinner A20 support
ARM: sun6i: Add restart code for the A31
ARM: sunxi: Add the Allwinner A31 compatible to the machine definition
From: Stephen Warren:
ARM: tegra: core SoC enhancements for 3.12
This branch includes a number of enhancements to core SoC support for
Tegra devices. The major new features are:
* Adds a new CPU-power-gated cpuidle state for Tegra114.
* Adds initial system suspend support for Tegra114, initially supporting
just CPU-power-gating during suspend.
* Adds "LP1" suspend mode support for all of Tegra20/30/114. This mode
both gates CPU power, and places the DRAM into self-refresh mode.
* A new DT-driven PCIe driver to Tegra20/30. The driver is also moved
from arch/arm/mach-tegra/ to drivers/pci/host/.
The PCIe driver work depends on the following tag from Thomas Petazzoni:
git://git.infradead.org/linux-mvebu.git mis-3.12.2
... which is merged into the middle of this pull request.
* tag 'tegra-for-3.12-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (33 commits)
ARM: tegra: disable LP2 cpuidle state if PCIe is enabled
MAINTAINERS: Add myself as Tegra PCIe maintainer
PCI: tegra: set up PADS_REFCLK_CFG1
PCI: tegra: Add Tegra 30 PCIe support
PCI: tegra: Move PCIe driver to drivers/pci/host
PCI: msi: add default MSI operations for !HAVE_GENERIC_HARDIRQS platforms
ARM: tegra: add LP1 suspend support for Tegra114
ARM: tegra: add LP1 suspend support for Tegra20
ARM: tegra: add LP1 suspend support for Tegra30
ARM: tegra: add common LP1 suspend support
clk: tegra114: add LP1 suspend/resume support
ARM: tegra: config the polarity of the request of sys clock
ARM: tegra: add common resume handling code for LP1 resuming
ARM: pci: add ->add_bus() and ->remove_bus() hooks to hw_pci
of: pci: add registry of MSI chips
PCI: Introduce new MSI chip infrastructure
PCI: remove ARCH_SUPPORTS_MSI kconfig option
PCI: use weak functions for MSI arch-specific functions
ARM: tegra: unify Tegra's Kconfig a bit more
ARM: tegra: remove the limitation that Tegra114 can't support suspend
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Add irqchip driver for the ImgTec PowerDown Controller (PDC) as found in
the TZ1090. The PDC has a number of general system wakeup (SysWake)
interrupts (which would for example be connected to a power button or an
external peripheral), and a number of peripheral interrupts which can
also wake the system but are connected straight to specific low-power
peripherals (such as RTC or Infrared). It has a single interrupt output
for SysWakes, and individual interrupt outputs for each peripheral.
The driver demuxes the SysWake interrupt line, and passes the peripheral
interrupts straight through. It also handles the set_wake interrupt
operation to enable/disable the appropriate wake event bits.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: linux-metag@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
* Support for memory mapped arch_timers
* Trivial fixes to the moxart timer code
* Documentation updates
Trivial conflicts in drivers/clocksource/arm_arch_timer.c. Fixed up
the newly added __cpuinit annotations as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some boards require custom PHY configuration, for example due to trace
length differences. Add the ability to configure these registers in
order to get the PHY to function on boards that need it.
Because PHYs are auto-detected based on MDIO device IDs, allow PHY
configuration to be specified in the parent Ethernet device node if no
PHY device node is present.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Stephen Warren:
ARM: tegra: device tree changes for 3.12
This branch contains all *.dts (device tree) changes for Tegra.
New features enabled are:
* PMICs on Dalmore
* CPU power-gating on Dalmore
* HDMI output on Beaver
* LP1 system suspend mode on almost all boards
* PCIe support on numerous Tegra20/30 boards
* USB support on Tegra30/114 boards
* Audio capture on Beaver and Dalmore
* Temperature sensor on Cardhu.
... along with a few DT cleanups.
* tag 'tegra-for-3.12-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (25 commits)
ARM: tegra: add Mic Jack to Dalmore device tree
ARM: tegra: add Mic Jack to Beaver device tree
ARM: tegra: add USB DT entries for Tegra114, Dalmore
ARM: tegra: add USB DT entries for Tegra30
ARM: dts: tegra: Increase prefetchable PCI memory space
ARM: tegra: Fix Beaver's PCIe lane configuration
ARM: tegra: Enable PCIe controller on Beaver
ARM: tegra: Enable PCIe controller on Cardhu
ARM: tegra: Add Tegra30 PCIe support
ARM: tegra: trimslice: Initialize PCIe from DT
ARM: tegra: harmony: Initialize PCIe from DT
ARM: tegra: tec: Add PCIe support
ARM: tegra: tamonten: Add PCIe support
ARM: tegra: Add Tegra20 PCIe support to DT
ARM: tegra: enable LP1 suspend mode
ARM: tegra: beaver: Enable HDMI output
ARM: tegra: use TEGRA_GPIO() in a couple more places
ARM: tegra: dalmore: fix the irq trigger type of Palmas MFD device
ARM: tegra: define valid function names in DT document
ARM: tegra: dalmore: add PM configurations for PMC
...
From: Linus Walleij:
Ux500 device tree enablement base for the v3.12
development cycle:
- Various cleanups like remove non-existant hardware from
the Snowball device tree, prefix all files with "ste-*"
- External regulators
- Documentation updates
- Delete some minor dangling platform data
- Pin control settings for U8540 through DT
* tag 'ux500-devicetree-for-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (22 commits)
ARM: ux500: fix devicetree builds
ARM: ux500: Remove u9540.dts as it's been replaced
ARM: ux500: Apply a ste-* prefix onto dbx5x0.dtsi
ARM: ux500: Apply a ste-* prefix onto stuib.dtsi
ARM: ux500: Apply a ste-* prefix onto hrefv60plus.dts
ARM: ux500: Apply a ste-* prefix onto hrefprev60.dts Signed-off-by: Lee Jones <lee.jones@linaro.org>
ARM: ux500: Apply a ste-* prefix onto href.dtsi
ARM: ux500: Apply a ste-* prefix onto ccu9540.dts
ARM: ux500: Apply a ste-* prefix onto ccu8540.dts
ARM: ux500: Apply a ste-* prefix onto snowball.dts
ARM: ux500: Remove Snowball DTS entry for ROHM BH1780GLI ambient light sensor
ARM: ux500: Remove Snowball DTS entry for TPS61052 chip
ARM: ux500: Remove Snowball DTS entry for National Semiconductor LP5521 LED chip
ARM: ux500: Remove Toshiba TC35892 I/O Expander's DT entry from Snowball's DTS
ARM: u8540: DT: Set pinctrl mapping to i2c0,1,2,4 & 5
ARM: u8540: Add Pinctrl Device Tree settings for uart0, uart2
ARM: ux500: Stop passing MMC's platform data for Device Tree boots
Documentation: Update binding for Nomadik and DBx5x based platforms
ARM: ux500: Supply external regulator names for Snowball's DT
ARM: ux500: Provide a supply name for the AB8500 AUX regulators to use
...
[ this is a follow-up to this discussion:
http://archive.arm.linux.org.uk/lurker/message/20130730.230827.a1ceb12a.en.html ]
This patchset renames all uses of "bcm," name bindings to
"brcm," as they were done prior to knowing that brcm had
already been standardized as Broadcom vendor prefix
(in Documentation/devicetree/bindings/vendor-prefixes.txt).
This will not cause any churn on devices because none of
these bindings have made it into production yet.
Also rename the the following dt binding docs that had "bcm,"
in their name for consistency:
- bcm,kona-sdhci.txt -> kona-sdhci.txt
- bcm,kona-timer.txt -> kona-timer.txt
Signed-off-by: Christian Daudt <csd@broadcom.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
This patch adds generic ac97 reset functions using pincontrol and gpio
parsed from devicetree.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
[ this is a follow-up to this discussion:
http://archive.arm.linux.org.uk/lurker/message/20130730.230827.a1ceb12a.en.html ]
This patchset renames all uses of "bcm," name bindings to
"brcm," as they were done prior to knowing that brcm had
already been standardized as Broadcom vendor prefix
(in Documentation/devicetree/bindings/vendor-prefixes.txt).
This will not cause any churn on devices because none of
these bindings have made it into production yet.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Christian Daudt <csd@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From Tony Lindgren:
Minimal DRA7xx based SoC core support via Rajendra Nayak <rnayak@ti.com>
* tag 'omap-for-v3.12/dra7xx' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (849 commits)
ARM: DRA7: Add the build support in omap2plus
ARM: DRA7: hwmod: Reuse the soc_ops used for OMAP4/5
ARM: DRA7: id: Add cpu detection support for DRA7xx based SoCs'
ARM: DRA7: Kconfig: Make ARCH_NR_GPIO default to 512
ARM: DRA7: board-generic: Add basic DT support
ARM: DRA7: Resue the clocksource, clockevent support
ARM: DRA7: Reuse io tables and add a new .init_early
ARM: DRA7: Reuse all of PRCM and MPUSS SMP infra
Linux 3.11-rc5
btrfs: don't loop on large offsets in readdir
Btrfs: check to see if root_list is empty before adding it to dead roots
Btrfs: release both paths before logging dir/changed extents
Btrfs: allow splitting of hole em's when dropping extent cache
Btrfs: make sure the backref walker catches all refs to our extent
Btrfs: fix backref walking when we hit a compressed extent
Btrfs: do not offset physical if we're compressed
Btrfs: fix extent buffer leak after backref walking
Btrfs: fix a bug of snapshot-aware defrag to make it work on partial extents
btrfs: fix file truncation if FALLOC_FL_KEEP_SIZE is specified
dlm: kill the unnecessary and wrong device_close()->recalc_sigpending()
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
MFC driver is updated to use only one clock instead of
two. Correcting this in the binding documentation.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Allwinner A31 has a different watchdog, with a slightly different
register layout, that requires a different restart code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
From Jason Cooper:
mvebu drivers changes for v3.12
- MBus devicetree bindings
- devbus update for address decoding window, cleanup
* tag 'drivers-3.12' of git://git.infradead.org/linux-mvebu: (35 commits)
memory: mvebu-devbus: Remove unused variable
ARM: mvebu: Relocate PCIe node in Armada 370 RD board
ARM: mvebu: Fix AXP-WiFi-AP DT for MBUS DT binding
ARM: mvebu: add support for the AXP WiFi AP board
ARM: mvebu: use dts pre-processor for mv78230
PCI: mvebu: Adapt to the new device tree layout
bus: mvebu-mbus: Add devicetree binding
ARM: kirkwood: Relocate PCIe device tree nodes
ARM: kirkwood: Introduce MBUS_ID
ARM: kirkwood: Introduce MBus DT node
ARM: kirkwood: Use the preprocessor on device tree files
ARM: kirkwood: Split DT and legacy MBus initialization
ARM: mvebu: Relocate Armada 370/XP PCIe device tree nodes
ARM: mvebu: Relocate Armada 370/XP DeviceBus device tree nodes
ARM: mvebu: Add BootROM to Armada 370/XP device tree
ARM: mvebu: Add MBus to Armada 370/XP device tree
ARM: mvebu: Use the preprocessor on Armada 370/XP device tree files
ARM: mvebu: Initialize MBus using the DT binding
ARM: mvebu: Remove the harcoded BootROM window allocation
bus: mvebu-mbus: Factorize Armada 370/XP data structures
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds WEIM support for all i.MX CPUs supported by the kernel.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Sarah writes:
xhci: Platform updates, 64-bit DMA, and trace events for 3.12.
Hi Greg,
This pull request includes one new feature for the xhci-plat driver (device
tree support). Felipe was fine with the patch last I checked, but hadn't
provided an official Acked-by line.
This pull request also includes 13 patches from my FOSS Outreach Program for
Women (OPW) intern, Xenia. She fixed a bug in the xHCI driver so that the
driver can allocate 64-bit consistent DMA, converted the driver to use dynamic
debugging, and added a bunch of new trace events for the xHCI driver. The
python plugin for trace-cmd should be up on git hub shortly, although the trace
events are usable without it.
I'm very happy with the progress that Xenia has made, and I look forward to her
future contributions to the Linux kernel.
Sarah Sharp
This change makes documentation of the the gpio-ranges property shorter
and more succinct, more consistent with the style of the rest of the
document, and not mention Linux-specifics such as the API
pinctrl_request_gpio(); DT binding documents should be OS independant
where at all possible. As part of this, the gpio-ranges property's format
is described in BNF form, in order to match the rest of the document.
This change also deprecates the #gpio-range-cells property. Such
properties are useful when one node references a second node, and that
second node dictates the format of the reference. However, that is not
the case here; the definition of gpio-ranges itself always dictates its
format entirely, and hence the value #gpio-range-cells must always be 3,
and hence there is no point requiring any referenced node to include
this property. The only remaining need for this property is to ensure
compatibility of DTs with older SW that was written to support the
previous version of the binding.
v4:
* Mention #gpio-range-cells as being deprecated, rather than removing all
documentation of that property. This allows DTs to be written in a
backwards-compatible way if desired, and also allows older DTs to be
interpreted fully using the latest documentation.
v3:
* Mention BNF in commit description.
* Fixed typo.
* Dropped patch that removed the deprecated property from *.dts, since
it's required to boot older kernels.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The bindings do not carry any resources, as the module only registers
the ASoC platform driver.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The pxa ssp DAI acts as a user of a pxa ssp port, and needs an
appropriate 'port' phandle in DT to reference the upstream.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a Mic Jack widget to the Tegra+RT5640 machine driver, and document
this in the DT binding. This enables the DT to include the Mic Jack in
the audio routing table, and hence enables capture of audio, in addition
to the previously-working playback.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
we defined some special properties for hardware flow control, document them
for DT-binding.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SGPIO PICs don't follow the standard very well and expect a certain
number of clock cycles or port frames in each SGPIO pattern. Add two
optional parameters in the DTB that can provide the number of extra
clock cycles to be sent before and after SGPIO pattern. Read those
parameters from the DTB and send the extra clock cycles.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
