When FW crashes, dmesg get polluted with the "FW not ready"
error message. Print it only once per FW lifecycle
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support for new chip revision. Revision read from the
internal register, PCIE config's "revision id" register
do not indicate HW version properly
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce enum to describe mapping type; allow 'none' in addition to
'single' and 'page'; this is preparation for GSO
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When setting fragmented skb for Tx, assign skb to the last descriptor
and set number of fragments in the 1-st one
On Tx complete, HW sets "DU" bit in Tx descriptor only for the last
descriptor; so search for it using number of fragments field.
Middle descriptors may have "DU" bit not set by the hardware.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When connection established, as reported by WMI_CONNECT_EVENTID,
4-way handshaking required for the secure connection is not done
yet. It is indicated by another WMI event. Wait for it and only then
allow data traffic. In case of non-secure connection, FW reports
"data port open" immediately after connection.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The registers for temperature compensation need to
be programmed only for active chains. Use the TX chainmask
to make sure that this is done properly for QCA953x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On older chips, the INI value differ in similar ways as cycpwr_thr1, so
convert it to absolute values as well.
Since the ANI algorithm is different here compared to the old
implementation (fewer steps, controlled at a different point in time),
it makes sense to use values similar to what would be applied for newer
chips, just without relying on INI defaults.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The table was copied from the ANI implementation of AR9300. It assumes
that the INI values contain a baseline value that is usable as reference
from which to increase/decrease based on the noise immunity value.
On older chips, the differences are bigger and especially AR5008/AR9001
are configured to much more sensitive values than what is useful.
Improve ANI behavior by reverting to the absolute values used in the
previous implementation (expressed as a simple formula instead of the
old table).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The primary purpose of this piece of code was to selectively disable
OFDM weak signal detection. The checks for this are elsewhere, and an
earlier commit relaxed the restrictions for older chips, which are more
sensitive to interference.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unify scnprintf calls and include the current OFDM/CCK immunity level.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
qi->tqi_readyTime is written directly to registers that expect
microseconds as unit instead of TU.
When setting the CABQ ready time, cur_conf->beacon_interval is in TU, so
convert it to microseconds before passing it to ath9k_hw.
This should hopefully fix some Tx DMA issues with buffered multicast
frames in AP mode.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit 558ff225de (ath9k: fix
ps-poll responses under a-mpdu sessions) non-data frames would have
gotten a sequence number from a TIDs sequence counter instead of
using the global sequence counter.
This can lead to instable connections.
To fix this only select the correct TID if we are processing a
data frame. Furthermore, prevent non-data frames to get a sequence
number from a TID sequence counter by adding a check to
ath_tx_setup_buffer.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: reduce baseband hang detection false positive rate"
added a delay in the loop checking the baseband state, however it was
unreachable due to previous 'continue' statements.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The help text were either out of date, too small or didn't exist at all. Also
move cfg80211 dependency to ath6kl_core module as it has all the calls to
cfg80211.
Fixes checkpatch warning:
WARNING: please write a paragraph that describes the config symbol fully
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
CHECK: Blank lines aren't necessary after an open brace '{'
CHECK: Blank lines aren't necessary before a close brace '}'
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
