This patch adds a new driver for keypad for Cirrus Logic CLPS711X CPUs.
Target CPU contain keyboard interface which can scan 8 column lines,
so we can read row GPIOs to read status and determine asserted state.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If a new (id == -1) ff effect was uploaded from userspace,
ff-core.c::input_ff_upload() will have assigned a positive number to the
new effect id. Currently, evdev.c::evdev_do_ioctl() will save this new id
to userspace, regardless of whether the upload succeeded or not.
On upload failure, this can be confusing because the dev->ff->effects[]
array will not contain an element at the index of that new effect id.
This patch fixes this by leaving the id unchanged after upload fails.
Note: Unfortunately applications should still expect changed effect id for
quite some time.
This has been discussed on:
http://www.mail-archive.com/linux-input@vger.kernel.org/msg08513.html
("ff-core effect id handling in case of a failed effect upload")
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Elias Vanderstuyft <elias.vds@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem fixes from Dmitry Torokhov:
"Updates to Synaptics touchpad to better cope with devices in Lenovo
laptops, and a couple more fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - add manual min/max quirk for ThinkPad X240
Input: synaptics - add manual min/max quirk
Input: cypress_ps2 - don't report as a button pads
Input: da9052_onkey - use correct register bit for key status
Input: adp5588-keys - get value from data out when dir is out
There is a new firmware version for the EDT-FT5x06 chip.
Add support for detecting the firmware version and handle the
differences appropriately.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The FT5x06 datasheet specifies a minimum reset width of 5ms and a
delay between deassertion of reset and start of reporting of 300ms.
Adjust the delays to conform to the datasheet.
With the original delays I sometimes experienced communication
timeouts when initializing the controller.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The new Lenovo Haswell series (-40's) contains a new Synaptics touchpad.
However, these new Synaptics devices report bad axis ranges.
Under Windows, it is not a problem because the Windows driver uses RMI4
over SMBus to talk to the device. Under Linux, we are using the PS/2
fallback interface and it occurs the reported ranges are wrong.
Of course, it would be too easy to have only one range for the whole
series, each touchpad seems to be calibrated in a different way.
We can not use SMBus to get the actual range because I suspect the firmware
will switch into the SMBus mode and stop talking through PS/2 (this is the
case for hybrid HID over I2C / PS/2 Synaptics touchpads).
So as a temporary solution (until RMI4 land into upstream), start a new
list of quirks with the min/max manually set.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
CC: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's dial back the default fuzz setting for most devices using this
driver, based on values from user feedback from forums and bug reports.
Signed-off-by: Clinton Sprain <clintonsprain@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit a1a7521064 moved to report EV_KEY event(KEY_POWER) instead of
reporting EV_PWR event(KEY_SUSPEND), but it didn't enable the capability, so
the KEY_POWER will not be reported to userspace by input core. this patch fixes
the issue.
Signed-off-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The cypress PS/2 trackpad models supported by the cypress_ps2 driver
emulate BTN_RIGHT events in firmware based on the finger position, as part
of this no motion events are sent when the finger is in the button area.
The INPUT_PROP_BUTTONPAD property is there to indicate to userspace that
BTN_RIGHT events should be emulated in userspace, which is not necessary
in this case.
When INPUT_PROP_BUTTONPAD is advertised userspace will wait for a motion
event before propagating the button event higher up the stack, as it needs
current abs x + y data for its BTN_RIGHT emulation. Since in the
cypress_ps2 pads don't report motion events in the button area, this means
that clicks in the button area end up being ignored, so
INPUT_PROP_BUTTONPAD actually causes problems for these touchpads, and
removing it fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=76341
Reported-by: Adam Williamson <awilliam@redhat.com>
Tested-by: Adam Williamson <awilliam@redhat.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The wrong register bit of the DA9052/3 PMIC registers was
used to determine the status on the ONKEY.
Also a failure in reading the status register will no longer
result in the work queue being rescheduled as that would result
in a (potentially) endless retry.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Acked-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Kconfig symbol X86_32 was introduced in October 2005, it's about time
to use it. This clears the last occurrence of the legacy
"X86 && !X86_64" construct :-)
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
I don't think the OLPC AP-SP driver is generally useful without OLPC
support. So make it depend on OLPC, unless build testing is enabled.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure that no callback is running before we teardown the module.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The snd_soc_dapm_xxxx_pin all require the dapm_mutex to be held when
they are called as they edit the dirty list, however very few of the
callers do so.
This patch adds unlocked versions of all the functions replacing the
existing implementations with one that holds the lock internally. We
also fix up the places where the lock was actually held on the caller
side.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This patch fix spelling typo in Documentation/DocBook.
It is because .html and .xml files are generated by make htmldocs,
I have to fix a typo within the source files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This cleanup series gets rid of <mach/timex.h> for platforms not using
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
* tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux:
ARM: ixp4xx: fix timer latch calculation
ARM: drop <mach/timex.h> for !ARCH_MULTIPLATFORM, too
ARM: rpc: stop using <mach/timex.h>
ARM: ixp4xx: stop using <mach/timex.h>
input: ixp4xx-beeper: don't use symbols from <mach/timex.h>
ARM: at91: don't use <mach/timex.h>
ARM: ep93xx: stop using mach/timex.h
ARM: mmp: stop using mach/timex.h
ARM: netx: stop using mach/timex.h
ARM: sa1100: stop using mach/timex.h
clocksource: sirf/marco+prima2: drop usage of CLOCK_TICK_RATE
rtc: pxa: drop unused #define TIMER_FREQ
rtc: at91sam9: include <mach/hardware.h> explicitly
ARM/serial: at91: switch atmel serial to use gpiolib
Signed-off-by: Olof Johansson <olof@lixom.net>
No need to return a 'fake' return value on platform_get_irq() failure.
Just return the error code itself instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The wrong register bit of the DA9052/3 PMIC registers was
used to determine the status on the ONKEY.
Also a failure in reading the status register will no longer
result in the work queue being rescheduled as that would result
in a (potentially) endless retry.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Acked-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change adds a delayed_work to detect the release of onkey since HW will
not generate interrupt for it.
At the same time, we move the KEY event to POWER instead of SUSPEND, which
will be suitable for both Android and Linux. Userspace PowerManager Daemon
will decide to suspend or shutdown based on how long we have touched onkey.
Signed-off-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As discussed here: http://ez.analog.com/message/35852, the 5587 revC and
5588 revB spec sheets contain a mistake in the GPIO_DAT_STATx register
description.
According to R.Shnell at ADI, as well as my own observations, it should
read: "GPIO data status (shows GPIO state when read for inputs)".
This commit changes the get value function accordingly.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In resume entry, use dev_get_drvdata() instead of to_platform_device(dev) +
platform_get_drvdata(pdev).
Signed-off-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since the IRQ handler always returns IRQ_HANDLED it means this irq is not
a shared IRQ at all. Or at least, the SW is not self-consistent now.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We can control whetehr device generates interrupts or not so let's
implement open and close methods of input device so that we do not do any
processing until there are users.
Tested-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
New version of the PCU firmware supports two new commands:
- IMS_PCU_CMD_OFN_SET_CONFIG which allows to write data to the
registers of one finger navigation(OFN) chip present on the device
- IMS_PCU_CMD_OFN_GET_CONFIG which allows to read data form the
registers of said chip.
This commit adds two helper functions to use those commands and sysfs
attributes to use them. It also exposes some OFN configuration
parameters via sysfs.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We first create backlight and then input devices so we should destroy them
in opposite order when handling errors.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
uinput is used in the xorg-integration-tests suite and in the wayland
test suite. These automated tests suites create many virtual input
devices and then hook something to read these newly created devices.
Currently, uinput does not provide the created input device, which means
that we rely on an heuristic to guess which input node was created.
The problem is that is heuristic is subjected to races between different
uinput devices or even with physical devices. Having a way to retrieve
the sysfs path allows us to find without any doubts the event node.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rework dev_pm_qos_add_ancestor_request() so that device PM QoS type
is passed to it as the third argument and make it support the
DEV_PM_QOS_LATENCY_TOLERANCE device PM QoS type (in addition to
DEV_PM_QOS_RESUME_LATENCY).
That will allow the drivers of devices without latency tolerance
hardware support to use their ancestors having it as proxies for
their latency tolerance requirements.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The current implementation prevents us to add variable-length ioctl.
Use a bunch of gotos instead of break to allow us to do so.
No functional changes.
Signed-off-by: Benjamin Tisssoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Devicetree support will be creating its own platfprm data structure that
is not attached to the device. Let's use the internal pointer to the
pdata instead of re-fetching it with dev_get_platdata().
Signed-off-by: Heiko Stuebner <heiko.stuebner@bqreaders.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A frame is a u8 array with the following structure:
[PAYLOAD_HEADER, PAYLOAD_LENGTH, ...PAYLOAD_BODY...]
PAYLOAD_BODY can be at most 255 bytes long, as it's size is represented
by PAYLOAD_LENGTH. Therefore we can reduce the stack memory allocated to
payload_buffer[] roughly by half, from 512 to 257 bytes.
Signed-off-by: Luis Ortega <luiorpe1@upv.es>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de> - bq Cervantes (imx6sl)
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The function zforce_read_packet() reads 2 values (bytes) of payload
header, validates them and then proceeds to read the payload body.
The function stores all these in a u8 buffer.
The PAYLOAD_LENGTH check seems to be trying to detect an overflow error.
However, since we are just reading a u8 value from the buffer, these
checks are unnecessary and we should simply compare against zero.
Signed-off-by: Luis Ortega <luiorpe1@upv.es>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de> - bq Cervantes (imx6sl)
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixed lines exceeding 80 characters long wherever possible,
as per the coding style.
Signed-off-by: Luis Ortega <luiorpe1@upv.es>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is usb_get_dev() in gtco_probe(), but there is no usb_put_dev()
anywhere in the driver.
As pointed out by Dmitry Torokhov:
The lifetime of gtco structure is already directly tied to lifetime of
usb_dev: when destroying usb_dev driver core will call remove() function
of currently bound driver (in our case gtco) which will destroy gtco
memory. Taking additional reference is not needed here.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds Fujitsu-Siemens AMILO Pro 8210 support to wistron_btns driver.
Functions are very similar to already supported AMILO Pro 3505, but 8210
has WIFI led.
Such functionality is needed to enable WiFi under Linux on 8210 when it
cold boots with hardware rfkill enabled, without booting another operating
system or running custom utility that calls appropriate BIOS function.
Signed-off-by: Jakub Bogusz <qboosh@pld-linux.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem updates from Dmitry Torokhov:
"Just a swath of driver fixes and cleanups, no new drivers this time
(although ALPS now supports one of the newer protocols, more to come)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
Input: wacom - add support for DTU-1031
Input: wacom - fix wacom->shared guards for dual input devices
Input: edt_ft5x06 - use devm_* functions where appropriate
Input: hyperv-keyboard - pass through 0xE1 prefix
Input: logips2pp - fix spelling s/reciver/receiver/
Input: delete non-required instances of include <linux/init.h>
Input: twl4030-keypad - convert to using managed resources
Input: twl6040-vibra - remove unneeded check for CONFIG_OF
Input: twl4030-keypad - add device tree support
Input: twl6040-vibra - add missing of_node_put
Input: twl4030-vibra - add missing of_node_put
Input: i8042 - cleanup SERIO_I8042 dependencies
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on x86
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on unicore32
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on sparc
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO for SH_CAYMAN
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on powerpc
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on mips
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on IA64
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on ARM/Footbridge
...
