Some ethernet adapter vendors are supplying products which support optional
(payed license) features. On some adapters this includes a hardware iscsi
initiator. The same adapters in a normal (no extra licenses) mode of
operation can be used as a software iscsi initiator. In addition, software
iscsi boot initiators are becoming a standard part of many vendors uefi
implementations. This is creating difficulties during early boot/install
determining the proper configuration method for these adapters when they
are used as a boot device.
The attached patch creates sysfs entries to expose information from the
acpi header of the ibft table. This information allows for a method to
easily determining if an ibft table was created by a ethernet card's
firmware or the system uefi/bios. In the case of a hardware initiator this
information in combination with the pci vendor and device id can be used
to ascertain any vendor specific behaviors that need to be accommodated.
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: David Bond <dbond@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The iBFT table only specifies a prefix length, not a netmask.
And the netmask is pretty much pointless for IPv6.
So introduce a new attribute 'prefix-len'.
Some older user-space code might rely on the netmask attribute
being present, so we should always display it.
Changes from v1:
- Combined two patches into one
Changes from v2:
- Cleaned up/corrected wording for patch description
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Pull SCSI fixes from James Bottomley:
"This is a couple of small fixes: one is a potential uninitialised
error variable in the alua code, potentially causing spurious failures
and the other is a problem caused by the conversion of SCSI to
hostwide tags which resulted in the qla1280 driver always failing in
host initialisation"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
qla1280: Don't allocate 512kb of host tags
scsi_dh_alua: uninitialized variable in alua_rtpg()
Replaced mpt3sas_base_flush_reply_queues() with
mpt3sas_base_sync_reply_irqs(),as mpt3sas_base_flush_reply_queues()
skips over reply queues that are currently busy (i.e. being handled by
interrupt processing in another core). If a reply queue is busy, then
call to synchronize_irq()in mpt3sas_base_sync_reply_irqs()make sures the
other core has finished flushing the queue and completed any calls to
the mid-layer scsi_done() routine.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modified driver code to use scsi_prot_ref_tag() API instead of
scsi_get_lba(), while initializing reference tag field in the CDB.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In-order to handle this 'MPI2_EVENT_ACTIVE_CABLE_EXCEPTION' event,
driver need to follow below steps,
1. Unmask the 'MPI2_EVENT_ACTIVE_CABLE_EXCEPTION' event,
so that FW can notify this event to host driver.
2. After receiving this event, add this event to AEN event queue,
for notifying this event to applications.
3. Then Print below message in kernel logs if the event data's reason
code is zero,
"Currently an active cable with ReceptacleID <ID_Value> cannot be powered
and devices connected to this active cable will not be seen. This active
cable requires <PowerValue_in_mW> of power"
This event is only for Intruder/Cutlass HBAs.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated MPI version and MPI header files.
ChangeList:
* Added SATADeviceWaitTime to SAS IO Unit Page 4
* Added EEDPObservedValue added to SCSI IO Reply message
* Added MPI2_EVENT_ACTIVE_CABLE_EXCEPTION and
MPI26_EVENT_DATA_ACTIVE_CABLE_EXCEPT
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This missing break statement bug predates git. It's a very minor thing,
it means that we print a '?' instead of a 'z' in dmesg.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The device ID obtained from the inquiry can only be of a single type.
The original code places a check for TYPE_ZBC right after the check for
TYPE_DISK. Logically, if the first if statement sees a device of a
TYPE_DISK and moves on to the second statement checking if not TYPE_ZBC,
it will always hit the continue.
[mkp: Applied by hand]
Signed-off-by: Petros Koutoupis <petros@petroskoutoupis.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Not every device will return a useable VPD identification, but still
might support ALUA. Rather than disable ALUA support we should be
allowing the device identification to be empty and attach individual
ALUA device handler to each devices.
[mkp: Fixed typo reported by Bart]
Reported-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Tested-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Permit changing of a LU name from a (fake) IEEE registered NAA (5) to a
locally assigned UUID. Using a UUID (RFC 4122) for a SCSI designation
descriptor (e.g. a LU name) was added in spc5r08.pdf (a draft INCITS
standard) on 25 January 2016. Add parameter uuid_ctl to use a separate
UUID for each LU (storage device) name. Additional option for all LU
names to have the same UUID (since their storage is shared). Previous
action of using NAA identifier for LU name remains the default.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cleanup some mode and vpd pages. Stop reporting SBC (disk) pages when
peripheral type is something else (e.g. tape). Update version
descriptors. Expand LBPRZ flag handling.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add submit_queue parameter (minimum and default: 1; maximum: nr_cpu_ids)
that controls how many queues are built, each with their own lock and
in_use bit vector. Add statistics parameter which is default off.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch introduces support for TCM_QLA2XXX_DEBUG and
associated tcm_qla2xxx_tpg->tpg_attrib.jam_host checking
used to test dropped packets to FC host environments.
Tested by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Laurence Oberman <loberman@redhat.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This stops abusing the common sess_kref to overload it for private
usage, which allows removing the shutdown_session method as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The caller assumes that "itnim" is NULL on error and non-NULL on success
but really "itnim" is uninitialized on error. This function should just
use normal error handling where it returns zero on success and negative
on failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Define the NCQ NON DATA command and update libsas to handle it
correctly.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
I actually read the error messages in my logs, and successful
initialization is not an error.
Arguably these log lines could be deleted entirely.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a cxlflash adapter goes into EEH recovery and multiple processes
(each having established its own context) are active, the EEH recovery
can hang if the processes attempt to recover in parallel. The symptom
logged after a couple of minutes is:
INFO: task eehd:48 blocked for more than 120 seconds.
Not tainted 4.5.0-491-26f710d+ #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
eehd 0 48 2
Call Trace:
__switch_to+0x2f0/0x410
__schedule+0x300/0x980
schedule+0x48/0xc0
rwsem_down_write_failed+0x294/0x410
down_write+0x88/0xb0
cxlflash_pci_error_detected+0x100/0x1c0 [cxlflash]
cxl_vphb_error_detected+0x88/0x110 [cxl]
cxl_pci_error_detected+0xb0/0x1d0 [cxl]
eeh_report_error+0xbc/0x130
eeh_pe_dev_traverse+0x94/0x160
eeh_handle_normal_event+0x17c/0x450
eeh_handle_event+0x184/0x370
eeh_event_handler+0x1c8/0x1d0
kthread+0x110/0x130
ret_from_kernel_thread+0x5c/0xa4
INFO: task blockio:33215 blocked for more than 120 seconds.
Not tainted 4.5.0-491-26f710d+ #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
blockio 0 33215 33213
Call Trace:
0x1 (unreliable)
__switch_to+0x2f0/0x410
__schedule+0x300/0x980
schedule+0x48/0xc0
rwsem_down_read_failed+0x124/0x1d0
down_read+0x68/0x80
cxlflash_ioctl+0x70/0x6f0 [cxlflash]
scsi_ioctl+0x3b0/0x4c0
sg_ioctl+0x960/0x1010
do_vfs_ioctl+0xd8/0x8c0
SyS_ioctl+0xd4/0xf0
system_call+0x38/0xb4
INFO: task eehd:48 blocked for more than 120 seconds.
The hang is because of a 3 way dead-lock:
Process A holds the recovery mutex, and waits for eehd to complete.
Process B holds the semaphore and waits for the recovery mutex.
eehd waits for semaphore.
The fix is to have Process B above release the semaphore before
attempting to acquire the recovery mutex. This will allow
eehd to proceed to completion.
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Based on "[PATH V2] scsi_debug: rework resp_report_luns" patch
sent by Tomas Winkler on Thursday, 26 Feb 2015. His notes:
1. Remove duplicated boundary checks which simplify the fill-in
loop
2. Use more of scsi generic API
Replace fixed length response array a with heap allocation
allowing up to 256 normal LUNs per target.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The qla1280 driver sets the scsi_host_template's can_queue field to 0xfffff
which results in an allocation failure when allocating the block layer tags
for the driver's queues. This was introduced with the change for host wide
tags in commit 64d513ac31 - "scsi: use host wide tags by default".
Reduce can_queue to MAX_OUTSTANDING_COMMANDS (512) to solve the allocation
error.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: 64d513ac31 - "scsi: use host wide tags by default"
Cc: stable@vger.kernel.org # v4.4
Cc: Laura Abbott <labbott@redhat.com>
Cc: Michael Reed <mdr@sgi.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
It's possible to use "err" without initializing it. If it happens to be
a 2 which is SCSI_DH_RETRY then that could cause a bug. Bart Van Assche
pointed out that we should probably re-initialize it for every iteration
through the retry loop.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
The most common commands in normal use are the READ and WRITE SCSI
commands. Use likely and unlikely hints along the path taken by these
commands. Rename check_readiness() to make_ua() and remove associated
dead code. Rename devInfoReg() to find_build_dev_info().
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Group most defines together first; followed by struct definitions and
then table and variable definitions. Normalize all function headers.
[mkp: Corrected hex value in WP/DPOFUA MODE SENSE comment]
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a negative value was placed in the delay parameter, a tasklet was
scheduled. Change the tasklet to a work queue. Previously a delay of -1
scheduled a high priority tasklet; since there are no high priority work
queues, treat -1 like other negative values in delay and schedule a work
item.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add 'j' to delay names to make it clearer that its unit is jiffies and
to differentiate it from sdebug_ndelay whose unit is nanoseconds.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver supports two command delay interfaces, the original one whose
unit is a jiffy, and a newer one whose unit is a nanosecond. Each had
different implementations. Keep both interfaces but simplify the
implemenation to use a single delay mechanism based on high resolution
timers.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove logic to optionally hold host_lock while each command is
queued. Keep module and sysfs host_lock parameters for backward
compatibility. Note in module parameter description that host_lock is
ignored.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shorten file scope static and constant names. Use more
get/put_unaligned calls to hide bit banging. Introduce
sdebug_verbose boolean to replace frequent masking of
option bit flags. Add GPL and bump version.
[mkp: Use logical instead of bitwise OR for LBP VPD flags]
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver was calling scsi_scan_host before enabling interrupts.
This has gone unnoticed except for customers running in intx mode.
Calling scsi_scan_host before interrupts are enabled causes
"irq XX: nobody cared" messages and the driver to hang.
This patch enables interrupts before the call to scsi_scan_host.
Reported-by: Piotr Karbowski <piotr.karbowski@gmail.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When KDUMP is triggered the driver first talks to the firmware in INTX
mode, but the adapter firmware is still in MSIX mode. Therefore the first
driver command hangs since the driver is waiting for an INTX response and
firmware gives a MSIX response. If when the OS is installed on a RAID
drive created by the adapter KDUMP will hang since the driver does not
receive a response in sync mode.
Fixed by: Change the firmware to INTX mode if it is in MSIX mode before
sending the first sync command.
Cc: stable@vger.kernel.org
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently driver completes double completed or spurious interrupted fibs.
This is not necessary and causes the SCSI mid layer to issue aborts and
resets, since completing a fib prematurely might trigger a race condition
resulting in the driver not calling the scsi_done callback.
Fixed by removing the call to fib complete.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware AIF messages about cache loss and data recovery are being missed
by the driver since currently they are not captured but rather let go.
This patch to capture those messages and log them for the user.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Typically under error conditions, it is possible for aac_command_thread()
to miss the wakeup from kthread_stop() and go back to sleep, causing it
to hang aac_shutdown.
In the observed scenario, the adapter is not functioning correctly and so
aac_fib_send() never completes (or time-outs depending on how it was
called). Shortly after aac_command_thread() starts it performs
aac_fib_send(SendHostTime) which hangs. When aac_probe_one
/aac_get_adapter_info send time outs, kthread_stop is called which breaks
the command thread out of it's hang.
The code will still go back to sleep in schedule_timeout() without
checking kthread_should_stop() so it causes aac_probe_one to hang until
the schedule_timeout() which is 30 minutes.
Fixed by: Adding another kthread_should_stop() before schedule_timeout()
Cc: stable@vger.kernel.org
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
