Commit:
129766708 ("x86/efi: Only map RAM into EFI page tables if in mixed-mode")
stopped creating 1:1 mappings for all RAM, when running in native 64-bit mode.
It turns out though that there are 64-bit EFI implementations in the wild
(this particular problem has been reported on a Lenovo Yoga 710-11IKB),
which still make use of the first physical page for their own private use,
even though they explicitly mark it EFI_CONVENTIONAL_MEMORY in the memory
map.
In case there is no mapping for this particular frame in the EFI pagetables,
as soon as firmware tries to make use of it, a triple fault occurs and the
system reboots (in case of the Yoga 710-11IKB this is very early during bootup).
Fix that by always mapping the first page of physical memory into the EFI
pagetables. We're free to hand this page to the BIOS, as trim_bios_range()
will reserve the first page and isolate it away from memory allocators anyway.
Note that just reverting 129766708 alone is not enough on v4.9-rc1+ to fix the
regression on affected hardware, as this commit:
ab72a27da ("x86/efi: Consolidate region mapping logic")
later made the first physical frame not to be mapped anyway.
Reported-by: Hanka Pavlikova <hanka@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vojtech Pavlik <vojtech@ucw.cz>
Cc: Waiman Long <waiman.long@hpe.com>
Cc: linux-efi@vger.kernel.org
Cc: stable@kernel.org # v4.8+
Fixes: 129766708 ("x86/efi: Only map RAM into EFI page tables if in mixed-mode")
Link: http://lkml.kernel.org/r/20170127222552.22336-1-matt@codeblueprint.co.uk
[ Tidied up the changelog and the comment. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull s390 fixes from Martin Schwidefsky:
"Another two bug fixes:
- ptrace partial write information leak
- a guest page hinting regression introduced with v4.6"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: Fix cmma unused transfer from pgste into pte
s390/ptrace: Preserve previous registers for short regset write
After emulating an unaligned access in delay slot of a branch, we
pretend as the delay slot never happened - so return back to actual
branch target (or next PC if branch was not taken).
Curently we did this by handling STATUS32.DE, we also need to clear the
BTA.T bit, which is disregarded when returning from original misaligned
exception, but could cause weirdness if it took the interrupt return
path (in case interrupt was acive too)
One ARC700 customer ran into this when enabling unaligned access fixup
for kernel mode accesses as well
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull "i.MX fixes for 4.10, 3rd round" from Shawn Guo:
- Fix a 'defined but not used' warning in MMDC driver when
CONFIG_PERF_EVENTS is disabled.
- Fix i.MX6DL device tree GPIO4_11 range setting.
- A bandaid fix for boot failure found on a couple of platforms due to
missing 'chosen' and 'memory' node.
* tag 'imx-fixes-4.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx: Pass 'chosen' and 'memory' nodes
ARM: dts: imx6dl: fix GPIO4 range
ARM: imx: hide unused variable in #ifdef
The Amlogic Meson GXBB/GXL/GXM secure monitor uses part of the memory space,
this patch adds these reserved zones.
Without such reserved memory zones, running the following stress command :
$ stress-ng --vm 16 --vm-bytes 128M --timeout 10s
multiple times:
Could lead to the following kernel crashes :
[ 46.937975] Bad mode in Error handler detected on CPU1, code 0xbf000000 -- SError
...
[ 47.058536] Internal error: Attempting to execute userspace memory: 8600000f [#3] PREEMPT SMP
...
Instead of the OOM killer.
Fixes: 4f24eda840 ("ARM64: dts: Prepare configs for Amlogic Meson GXBaby")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
[khilman: added Fixes tag, added _reserved and unit addresses]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
OdroidC2 GbE link breaks under heavy tx transfer. This happens even if the
MAC does not enable Energy Efficient Ethernet (No Low Power state Idle on
the Tx path). The problem seems to come from the phy Rx path, entering the
LPI state.
Disabling EEE advertisement on the phy prevent this feature to be
negociated with the link partner and solve the issue.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Since v4.10-rc1, the following logs appears in loop :
[ 801.953836] usb usb6-port1: Cannot enable. Maybe the USB cable is bad?
[ 801.960455] xhci-hcd xhci-hcd.0.auto: Cannot set link state.
[ 801.966611] usb usb6-port1: cannot disable (err = -32)
[ 806.083772] usb usb6-port1: Cannot enable. Maybe the USB cable is bad?
[ 806.090370] xhci-hcd xhci-hcd.0.auto: Cannot set link state.
[ 806.096494] usb usb6-port1: cannot disable (err = -32)
After analysis, xhci try to set link in U3 and returns an error.
Using snps,dis_u3_susphy_quirk fix this issue.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
On ACPI based systems where the topology is setup using the API
store_cpu_topology, at the moment we do not have necessary code
to parse cpu capacity and handle cpufreq notifier, thus
resulting in a kernel panic.
Stack:
init_cpu_capacity_callback+0xb4/0x1c8
notifier_call_chain+0x5c/0xa0
__blocking_notifier_call_chain+0x58/0xa0
blocking_notifier_call_chain+0x3c/0x50
cpufreq_set_policy+0xe4/0x328
cpufreq_init_policy+0x80/0x100
cpufreq_online+0x418/0x710
cpufreq_add_dev+0x118/0x180
subsys_interface_register+0xa4/0xf8
cpufreq_register_driver+0x1c0/0x298
cppc_cpufreq_init+0xdc/0x1000 [cppc_cpufreq]
do_one_initcall+0x5c/0x168
do_init_module+0x64/0x1e4
load_module+0x130c/0x14d0
SyS_finit_module+0x108/0x120
el0_svc_naked+0x24/0x28
Fixes: 7202bde8b7 ("arm64: parse cpu capacity-dmips-mhz from DT")
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Anton says: In commit 4db7327194 ("powerpc: Add option to use jump
label for cpu_has_feature()") and commit c12e6f24d4 ("powerpc: Add
option to use jump label for mmu_has_feature()") we added:
BUILD_BUG_ON(!__builtin_constant_p(feature))
to cpu_has_feature() and mmu_has_feature() in order to catch usage
issues (such as cpu_has_feature(cpu_has_feature(X), which has happened
once in the past). Unfortunately LLVM isn't smart enough to resolve
this, and it errors out.
I work around it in my clang/LLVM builds of the kernel, but I have just
discovered that it causes a lot of issues for the bcc (eBPF) trace tool
(which uses LLVM).
For now just #ifdef it away for clang builds.
Fixes: 4db7327194 ("powerpc: Add option to use jump label for cpu_has_feature()")
Fixes: c12e6f24d4 ("powerpc: Add option to use jump label for mmu_has_feature()")
Cc: stable@vger.kernel.org # v4.8+
Reported-by: Anton Blanchard <anton@samba.org>
Tested-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is needed on HS38 cores, for setting up IO-Coherency aperture properly
The polling could perturb the caches and coherecy fabric which could be
wrong in the small window when Master is setting up IOC aperture etc
in arc_cache_init()
We do it only for ARCv2 based builds to not affect EZChip ARCompact
based platform.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
For run-on-reset SMP configs, non master cores call a routine which
waits until Master gives it a "go" signal (currently using a shared
mem flag). The same routine then jumps off the well known entry point of
all non Master cores i.e. @first_lines_of_secondary
This patch moves out the last part into one single place in early boot
code.
This is better in terms of absraction (the wait API only waits) and
returns, leaving out the "jump off to" part.
In actual implementation this requires some restructuring of the early
boot code as well as Master now jumps to BSS setup explicitly,
vs. falling thru into it before.
Technically this patch doesn't cause any functional change, it just
moves the ugly #ifdef'ry from assembly code to "C"
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
commit 3c7c7a2fc8 ("ARC: Don't use "+l" inline asm constraint")
modified the inline assembly to setup LP_COUNT register manually and NOT
rely on gcc to do it (with the +l inline assembler contraint hint, now
being retired in the compiler)
However the fix was flawed as we didn't add LP_COUNT to asm clobber list,
meaning gcc doesn't know that LP_COUNT or zero-delay-loops are in action
in the inline asm.
This resulted in some fun - as nested ZOL loops were being generared
| mov lp_count,250000 ;16 # tmp235,
| lp .L__GCC__LP14 # <======= OUTER LOOP (gcc generated)
| .L14:
| ld r2, [r5] # MEM[(volatile u32 *)prephitmp_43], w
| dmb 1
| breq r2, -1, @.L21 #, w,,
| bbit0 r2,1,@.L13 # w,,
| ld r4,[r7] ;25 # loops_per_jiffy, loops_per_jiffy
| mpymu r3,r4,r6 #, loops_per_jiffy, tmp234
|
| mov lp_count, r3 # <====== INNER LOOP (from inline asm)
| lp 1f
| nop
| 1:
| nop_s
| .L__GCC__LP14: ; loop end, start is @.L14 #,
This caused issues with drivers relying on sane behaviour of udelay
friends.
With LP_COUNT added to clobber list, gcc doesn't generate the outer
loop in say above case.
Addresses STAR 9001146134
Reported-by: Joao Pinto <jpinto@synopsys.com>
Fixes: 3c7c7a2fc8 ("ARC: Don't use "+l" inline asm constraint")
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Ignore value of interrupt distribution mode for common interrupts in
IDU since setting of affinity using value from Device Tree is deprecated
in ARC. Originally it is done in idu_irq_xlate() function and it is
semantically wrong and does not guaranty that an affinity value will be
set properly. idu_irq_enable() function is better place for
initialization of common interrupts.
By default send all common interrupts to all available online CPUs.
The affinity of common interrupts in IDU must be set manually since
in some cases the kernel will not call irq_set_affinity() by itself:
1. When the kernel is not configured with support of SMP.
2. When the kernel is configured with support of SMP but upper
interrupt controllers does not support setting of the affinity
and cannot propagate it to IDU.
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Commit 7f107887d1 ("ARM: dts: imx: Remove skeleton.dtsi") causes boot
issues when the bootloader does not create a 'chosen' node if such node
is not present in the dtb.
The reason for the boot failure is well explained by Javier Martinez
Canillas: "the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info."
, so pass an empty 'chosen' node to fix the boot problem.
This issue has been seen in the kernelci reports with Barebox as
bootloader.
Also pass the 'memory' node in order to fix boot issues on the SolidRun
iMX6 platforms.
Fixes: 7f107887d1 ("ARM: dts: imx: Remove skeleton.dtsi")
Reported-by: kernelci.org bot <bot@kernelci.org>
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Unfortunately the stack protector support we merged recently only works
on some toolchains. If the toolchain is built without glibc support
everything works fine, but if glibc is built then it leads to a panic
at boot.
The solution is not rc5 material, so revert the support for now. This
reverts commits:
6533b7c16e ("powerpc: Initial stack protector (-fstack-protector) support")
902e06eb86 ("powerpc/32: Change the stack protector canary value per task")
Fixes: 6533b7c16e ("powerpc: Initial stack protector (-fstack-protector) support")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In __eeh_clear_pe_frozen_state(), we should pass the flag's value
instead of its address to eeh_unfreeze_pe(). The isolated flag is
cleared if no error returned from __eeh_clear_pe_frozen_state(). We
never observed the error from the function. So the isolated flag should
have been always cleared, no real issue is caused because of the misused
@flag.
This fixes the code by passing the value of @flag to eeh_unfreeze_pe().
Fixes: 5cfb20b96f ("powerpc/eeh: Emulate EEH recovery for VFIO devices")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The compacted-format XSAVES area is determined at boot time and
never changed after. The field xsave.header.xcomp_bv indicates
which components are in the fixed XSAVES format.
In fpstate_init() we did not set xcomp_bv to reflect the XSAVES
format since at the time there is no valid data.
However, after we do copy_init_fpstate_to_fpregs() in fpu__clear(),
as in commit:
b22cbe404a x86/fpu: Fix invalid FPU ptrace state after execve()
and when __fpu_restore_sig() does fpu__restore() for a COMPAT-mode
app, a #GP occurs. This can be easily triggered by doing valgrind on
a COMPAT-mode "Hello World," as reported by Joakim Tjernlund and
others:
https://bugzilla.kernel.org/show_bug.cgi?id=190061
Fix it by setting xcomp_bv correctly.
This patch also moves the xcomp_bv initialization to the proper
place, which was in copyin_to_xsaves() as of:
4c833368f0 x86/fpu: Set the xcomp_bv when we fake up a XSAVES area
which fixed the bug too, but it's more efficient and cleaner to
initialize things once per boot, not for every signal handling
operation.
Reported-by: Kevin Hao <haokexin@gmail.com>
Reported-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Signed-off-by: Yu-cheng Yu <yu-cheng.yu@intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi V. Shankar <ravi.v.shankar@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: haokexin@gmail.com
Link: http://lkml.kernel.org/r/1485212084-4418-1-git-send-email-yu-cheng.yu@intel.com
[ Combined it with 4c833368f0. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ensure that if userspace supplies insufficient data to
PTRACE_SETREGSET to fill all the registers, the thread's old
registers are preserved.
convert_vx_to_fp() is adapted to handle only a specified number of
registers rather than unconditionally handling all of them: other
callers of this function are adapted appropriately.
Based on an initial patch by Dave Martin.
Cc: stable@vger.kernel.org
Reported-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
prom_init.c calls 'instance-to-package' twice, but the return
is not checked during prom_find_boot_cpu(). The result is then
passed to prom_getprop(), which could be PROM_ERROR. Add a return check
to prevent this.
This was found on a pasemi system, where CFE doesn't have a working
'instance-to package' prom call.
Before Commit 5c0484e25e ('powerpc: Endian safe trampoline') the area
around addr 0 was mostly 0's and this doesn't cause a problem. Once the
macro 'FIXUP_ENDIAN' has been added to head_64.S, the low memory area
now has non-zero values, which cause the prom_getprop() call
to hang.
mpe: Also confirmed that under SLOF if 'instance-to-package' did fail
with PROM_ERROR we would crash in SLOF. So the bug is not specific to
CFE, it's just that other open firmwares don't trigger it because they
have a working 'instance-to-package'.
Fixes: 5c0484e25e ("powerpc: Endian safe trampoline")
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull tile bugfix from Chris Metcalf:
"This avoids an issue with short userspace reads for regset via ptrace"
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile/ptrace: Preserve previous registers for short regset write
Update the ARMv8 Crypto Extensions and the plain NEON AES implementations
in CBC and CTR modes to return the next IV back to the skcipher API client.
This is necessary for chaining to work correctly.
Note that for CTR, this is only done if the request is a round multiple of
the block size, since otherwise, chaining is impossible anyway.
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
GPIO4_11 is on pin 152(MX6DL_PAD_KEY_ROW2) and not on pin
151(MX6DL_PAD_KEY_ROW1).
I found the error while booting a mainline kernel on APF6S SoM and
noticed the following message:
[ 2.609337] imx6dl-pinctrl 20e0000.iomuxc: pin MX6DL_PAD_KEY_ROW1
already requested by 20a8000.gpio:105; cannot claim for 20a8000.gpio:107
[ 2.621884] imx6dl-pinctrl 20e0000.iomuxc: pin-151 (20a8000.gpio:107)
status -22
[ 2.629303] spi_imx 2008000.ecspi: Can't get CS GPIO 107
With this patch, the message is gone and spi_imx driver probes correctly.
Fixes: bb728d662b ("ARM: dts: add gpio-ranges property to iMX GPIO controllers")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This was meant to save us the scanning of the microcode containter in
the initrd since the first AP had already done that but it can also hurt
us:
Imagine a single hyperthreaded CPU (Intel(R) Atom(TM) CPU N270, for
example) which updates the microcode on the BSP but since the microcode
engine is shared between the two threads, the update on CPU1 doesn't
happen because it has already happened on CPU0 and we don't find a newer
microcode revision on CPU1.
Which doesn't set the intel_ucode_patch pointer and at initrd
jettisoning time we don't save the microcode patch for later
application.
Now, when we suspend to RAM, the loaded microcode gets cleared so we
need to reload but there's no patch saved in the cache.
Removing the optimization fixes this issue and all is fine and dandy.
Fixes: 06b8534cb7 ("x86/microcode: Rework microcode loading")
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170120202955.4091-2-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
A bugfix added a new local variable that is only used inside of an #ifdef
section, and unused if CONFIG_PERF_EVENTS is disabled:
arch/arm/mach-imx/mmdc.c:63:25: warning: 'cpuhp_mmdc_state' defined but not used [-Wunused-variable]
This moves the variable down inside that same ifdef.
Fixes: a051f220d6 ("ARM/imx/mmcd: Fix broken cpu hotplug handling")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull x86 fix from Thomas Gleixner:
"Restore the retrigger callbacks in the IO APIC irq chips. That
addresses a long standing regression which got introduced with the
rewrite of the x86 irq subsystem two years ago and went unnoticed so
far"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ioapic: Restore IO-APIC irq_chip retrigger callback
Pull ARC fixes from Vineet Gupta:
- more intc updates [Yuriv]
- fix module build when unwinder is turned off
- IO Coherency Programming model updates
- other miscellaneous
* tag 'arc-4.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Revert "ARC: mm: IOC: Don't enable IOC by default"
ARC: mm: split arc_cache_init to allow __init reaping of bulk
ARCv2: IOC: Use actual memory size to setup aperture size
ARCv2: IOC: Adhere to progamming model guidelines to avoid DMA corruption
ARCv2: IOC: refactor the IOC and SLC operations into own functions
ARC: module: Fix !CONFIG_ARC_DW2_UNWIND builds
ARCv2: save r30 on kernel entry as gcc uses it for code-gen
ARCv2: IRQ: Call entry/exit functions for chained handlers in MCIP
ARC: IRQ: Use hwirq instead of virq in mask/unmask
ARC: mmu: clarify the MMUv3 programming model
Pull powerpc fixes from Michael Ellerman:
"Two fixes for fallout from the hugetlb changes we merged this cycle.
Ten other fixes, four only affect Power9, and the rest are a bit of a
mixture though nothing terrible.
Thanks to: Aneesh Kumar K.V, Anton Blanchard, Benjamin Herrenschmidt,
Dave Martin, Gavin Shan, Madhavan Srinivasan, Nicholas Piggin, Reza
Arbab"
* tag 'powerpc-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Ignore reserved field in DCSR and PVR reads and writes
powerpc/ptrace: Preserve previous TM fprs/vsrs on short regset write
powerpc/ptrace: Preserve previous fprs/vsrs on short regset write
powerpc/perf: Use MSR to report privilege level on P9 DD1
selftest/powerpc: Wrong PMC initialized in pmc56_overflow test
powerpc/eeh: Enable IO path on permanent error
powerpc/perf: Fix PM_BRU_CMPL event code for power9
powerpc/mm: Fix little-endian 4K hugetlb
powerpc/mm/hugetlb: Don't panic when we don't find the default huge page size
powerpc: Fix pgtable pmd cache init
powerpc/icp-opal: Fix missing KVM case and harden replay
powerpc/mm: Fix memory hotplug BUG() on radix
Pull KVM fixes from Radim Krčmář:
"ARM:
- Fix for timer setup on VHE machines
- Drop spurious warning when the timer races against the vcpu running
again
- Prevent a vgic deadlock when the initialization fails (for stable)
s390:
- Fix a kernel memory exposure (for stable)
x86:
- Fix exception injection when hypercall instruction cannot be
patched"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: s390: do not expose random data via facility bitmap
KVM: x86: fix fixing of hypercalls
KVM: arm/arm64: vgic: Fix deadlock on error handling
KVM: arm64: Access CNTHCTL_EL2 bit fields correctly on VHE systems
KVM: arm/arm64: Fix occasional warning from the timer work function
Pull arm64 fixes from Catalin Marinas:
- avoid potential stack information leak via the ptrace ABI caused by
uninitialised variables
- SWIOTLB DMA API fall-back allocation fix when the SWIOTLB buffer is
not initialised (all RAM is suitable for 32-bit DMA masks)
- fix the bad_mode function returning for unhandled exceptions coming
from user space
- fix name clash in __page_to_voff()
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: avoid returning from bad_mode
arm64/ptrace: Reject attempts to set incomplete hardware breakpoint fields
arm64/ptrace: Avoid uninitialised struct padding in fpr_set()
arm64/ptrace: Preserve previous registers for short regset write
arm64/ptrace: Preserve previous registers for short regset write
arm64/ptrace: Preserve previous registers for short regset write
arm64: mm: avoid name clash in __page_to_voff()
arm64: Fix swiotlb fallback allocation
kvm_s390_get_machine() populates the facility bitmap by copying bytes
from the host results that are stored in a 256 byte array in the prefix
page. The KVM code does use the size of the target buffer (2k), thus
copying and exposing unrelated kernel memory (mostly machine check
related logout data).
Let's use the size of the source buffer instead. This is ok, as the
target buffer will always be greater or equal than the source buffer as
the KVM internal buffers (and thus S390_ARCH_FAC_LIST_SIZE_BYTE) cover
the maximum possible size that is allowed by STFLE, which is 256
doublewords. All structures are zero allocated so we can leave bytes
256-2047 unchanged.
Add a similar fix for kvm_arch_init_vm().
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
[found with smatch]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
CC: stable@vger.kernel.org
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
IBM bit 31 (for the rest of us - bit 0) is a reserved field in the
instruction definition of mtspr and mfspr. Hardware is encouraged to
(and does) ignore it.
As a result, if userspace executes an mtspr DSCR with the reserved bit
set, we get a DSCR facility unavailable exception. The kernel fails to
match against the expected value/mask, and we silently return to
userspace to try and re-execute the same mtspr DSCR instruction. We
loop forever until the process is killed.
We should do something here, and it seems mirroring what hardware does
is the better option vs killing the process. While here, relax the
matching of mfspr PVR too.
Cc: stable@vger.kernel.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET
to fill all the check pointed registers, the thread's old check pointed
registers are preserved.
Fixes: 9d3918f7c0 ("powerpc/ptrace: Enable support for NT_PPC_CVSX")
Fixes: 19cbcbf75a ("powerpc/ptrace: Enable support for NT_PPC_CFPR")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET
to fill all the registers, the thread's old registers are preserved.
Fixes: c6e6771b87 ("powerpc: Introduce VSX thread_struct and CONFIG_VSX")
Cc: stable@vger.kernel.org # v2.6.27+
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull ARM SoC fixes from Olof Johansson:
"We've been sitting on fixes for a while, and they keep trickling in at
a low rate. Nothing in here comes across as particularly scary or
noteworthy, for the most part it's a large collection of small DT
tweaks"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (24 commits)
ARM: dts: da850-evm: fix read access to SPI flash
ARM: dts: omap3: Fix Card Detect and Write Protect on Logic PD SOM-LV
ARM64: dts: meson-gxbb-odroidc2: Disable SCPI DVFS
ARM: dts: OMAP5 / DRA7: indicate that SATA port 0 is available.
ARM: dts: NSP: Fix DT ranges error
ARM: multi_v7_defconfig: set bcm47xx watchdog
ARM: multi_v7_defconfig: fix config typo
ARM: dts: dra72-evm-revc: fix typo in ethernet-phy node
soc: ti: wkup_m3_ipc: Fix error return code in wkup_m3_ipc_probe()
ARM: ux500: fix prcmu_is_cpu_in_wfi() calculation
ARM: dts: sunxi: Change node name for pwrseq pin on Olinuxino-lime2-emmc
ARM: dts: sun8i: Support DTB build for NanoPi M1
ARM: dts: sun6i: hummingbird: Enable display engine again
ARM: dts: sun6i: Disable display pipeline by default
ARM, ARM64: dts: drop "arm,amba-bus" in favor of "simple-bus" part 3
ARM: dts: imx6qdl-nitrogen6_som2: fix sgtl5000 pinctrl init
ARM: dts: imx6qdl-nitrogen6_max: fix sgtl5000 pinctrl init
ARM: OMAP1: DMA: Correct the number of logical channels
ARM: dts: am335x-icev2: Remove the duplicated pinmux setting
ARM: OMAP2+: Fix WL1283 Bluetooth Baud Rate
...
Read access to the SPI flash are broken on da850-evm, i.e. the data
read is not what is actually programmed on the flash.
According to the datasheet for the M25P64 part present on the da850-evm,
if the SPI frequency is higher than 20MHz then the READ command is not
usable anymore and only the FAST_READ command can be used to read data.
This commit specifies in the DTS that we should use FAST_READ command
instead of the READ command.
Cc: stable@vger.kernel.org
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Fabien Parent <fparent@baylibre.com>
[nsekhar@ti.com: subject line adjustment]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull PCI fixes from Bjorn Helgaas:
- recognize that a PCI-to-PCIe bridge originates a PCIe hierarchy, so
we enumerate that hierarchy correctly
- X-Gene: fix a change merged for v4.10 that broke MSI
- Keystone: avoid reading undefined registers, which can cause
asynchronous external aborts
- Supermicro X8DTH-i/6/iF/6F: ignore broken _CRS that caused us to
change (and break) existing I/O port assignments
* tag 'pci-v4.10-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/MSI: pci-xgene-msi: Fix CPU hotplug registration handling
PCI: Enumerate switches below PCI-to-PCIe bridges
x86/PCI: Ignore _CRS on Supermicro X8DTH-i/6/iF/6F
PCI: designware: Check for iATU unroll only on platforms that use ATU
Pull two s390 bug fixes from Martin Schwidefsky:
"Two changes, the first is a fix to add a missing memory clobber to the
inline assembly to load control registers. This has not caused any
issues so far, but who knows what code gcc will generate in future
versions.
The second change is an update for the default configurations. This
includes CONFIG_BUG_ON_DATA_CORRUPTION=y, we want this to be enabled
for s390. The usual approach to debug problems on production systems
is to use crash on a system dump and for us avoiding data corruptions
is priority one"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: update defconfigs
s390/ctl_reg: make __ctl_load a full memory barrier
Generally, taking an unexpected exception should be a fatal event, and
bad_mode is intended to cater for this. However, it should be possible
to contain unexpected synchronous exceptions from EL0 without bringing
the kernel down, by sending a SIGILL to the task.
We tried to apply this approach in commit 9955ac47f4 ("arm64:
don't kill the kernel on a bad esr from el0"), by sending a signal for
any bad_mode call resulting from an EL0 exception.
However, this also applies to other unexpected exceptions, such as
SError and FIQ. The entry paths for these exceptions branch to bad_mode
without configuring the link register, and have no kernel_exit. Thus, if
we take one of these exceptions from EL0, bad_mode will eventually
return to the original user link register value.
This patch fixes this by introducing a new bad_el0_sync handler to cater
for the recoverable case, and restoring bad_mode to its original state,
whereby it calls panic() and never returns. The recoverable case
branches to bad_el0_sync with a bl, and returns to userspace via the
usual ret_to_user mechanism.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Fixes: 9955ac47f4 ("arm64: don't kill the kernel on a bad esr from el0")
Reported-by: Mark Salter <msalter@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The programming model has been fixed with prev patches so re-enable it
by default
This reverts commit 23cb1f6440.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
arc_cache_init() is called for each core so can't be tagged __init.
However bulk of it is only executed by master core and thus is candidate
for __init reaping.
So split it up to allow that.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Fixes for omaps for v4.10-rc cycle. Mostly a DMA regression fix for
omap1, and then a handful of trivial fixes for boards and devices to
work:
- Fixes TI wilink bluetooth strange platform data baud rate
- Remove duplicate pinmux line for am335x-icev2
- Fix omap1 dma regression
- Fix uninitialized return value for wkup_m3_ipc_probe()
- Fix Ethernet PHY binding typo for dra72-evm
- Fix init for omap5 and dra7 sata ports
- Fix mmc card detect pin for Logic PD SOM-LV
* tag 'omap-for-v4.10/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3: Fix Card Detect and Write Protect on Logic PD SOM-LV
ARM: dts: OMAP5 / DRA7: indicate that SATA port 0 is available.
ARM: dts: dra72-evm-revc: fix typo in ethernet-phy node
soc: ti: wkup_m3_ipc: Fix error return code in wkup_m3_ipc_probe()
ARM: OMAP1: DMA: Correct the number of logical channels
ARM: dts: am335x-icev2: Remove the duplicated pinmux setting
ARM: OMAP2+: Fix WL1283 Bluetooth Baud Rate
Signed-off-by: Olof Johansson <olof@lixom.net>
vs. fixed 512M before.
But this still assumes that all of memory is under IOC which may not be
true for the SoC. Improve that later when this becomes a real issue, by
specifying this from DT.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
On AXS103 release bitfiles, DMA data corruptions were seen because IOC
setup was not following the recommended way in documentation.
Flipping IOC on when caches are enabled or coherency transactions are in
flight, might cause some of the memory operations to not observe
coherency as expected.
So strictly follow the programming model recommendations as documented
in comment header above arc_ioc_setup()
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
