The Hummingbird A31 has headset and line in audio jacks and an onboard
mic routed to the pins for the SoC's internal codec. The line out pins
are routed to an onboard speaker amp, whose output is available on a
pin header.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A31 SoC includes the Allwinner audio codec, capable of 24-bit
playback up to 192 kHz and 24-bit capture up to 48 kHz.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
NanoPi M1 is the Allwinner H3 based board.
This patch enables UART for debug console, LEDs, GPIO key switch, 3 USB
host ports, a micro SD slot and related power and pin controls by using
NanoPi common dtsi file.
Cc: James Pettigrew <james@innovum.com.au>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch provides a common file for NanoPi M1 and Neo SBC.
Those have common features below.
* UART0
* 2 LEDs
* USB host (EHCI3, OHCI3) and PHY
* MicroSD
* GPIO key switch
Cc: James Pettigrew <james@innovum.com.au>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The board has a Ampak AP6330 WiFi/BT/FM module. Inside it is a Broadcom
BCM4330 WiFi/BT/FM combo IC. The WiFi portion is connected to mmc1, with
the enabling pin connected to PL2. The AC100 RTC provides a low power
clock signal.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The board has a Ampak AP6330 WiFi/BT/FM module. Inside it is a Broadcom
BCM4330 WiFi/BT/FM combo IC. The WiFi portion is connected to mmc1, with
the enabling pin connected to PL2. The AC100 RTC provides a low power
clock signal.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A80, mmc1 is available on pingroup G. Designs mostly use this
to connect to an SDIO WiFi chip.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The I2C1 and SPI2 buses are exposed on the CHIP headers, and are not
explicitly dedicated to anything.
Add them to the DTS with the muxing already set, but keep them disabled.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The SPI2 pins on the sun5i PB bank are only available on the A10s. Rename
the A10s only bank so that it doesn't confuse people on the other SoCs
whose indexing would start at b.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The WiFi chip is powered through a GPIO and two regulators in parallel.
Since that case is not supported yet, just set them as always on before we
rework the regulator framework to deal with those.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The CHIP Pro is a small embeddable board. It features a GR8, an AXP209
PMIC, a 512MB SLC NAND and a WiFi/BT chip.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The PWM controller has two different channels, but only the first pin was
exposed in the DTSI. Add the other one.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The GR8 has access to the UART3 controller, which was missing in the
DTSI. Add it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The LCD0 controller on the A31 can do RGB output up to 8 bits per
channel. Add the pins for RGB888 output.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A31 has 2 parallel display pipelines, which can be intermixed.
However the driver currently only supports one of them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sun7i-a20-olimex-som-evb.dts doesn't contain cpu-supply needed for
voltage-scaling with cpufreq-dt so define it.
The default voltages are defined in sun7i-a20.dtsi.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have support for the VGA bridges using our DRM driver, enable
the display engine for the Olimex A13-Olinuxino.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The pinmux setting nodes for the A31 were added out of alphabetical
order. Sort them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviews have found that sun5i was a better prefix after all for the GR8.
Rename the relevant device trees before it's too late.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The polarity of the card detect pin is inverted.
Change it to reflect the right polarity for the board
which is ACTIVE_LOW.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This pull request brings in DT changes for BCM2835: pinctrl setup
cleanups, GPIO line naming, and the node for the new thermal driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This enables the usb otg controller for the lcdk board.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds the device tree node for the usb otg
controller present in the da850 family of SoC's.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Child of mvpp2 ethernet do not have a reg property so the unit name
should not contain an address: remove them.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As it was previously done for kirkwood and for aramda 370/XP, this adds
missing node labels to Armada 375 and SoC specific nodes to allow to
reference them more easily.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The gpio-key nodes do not have a reg property, so remove the address from
the unit name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The dsa node does not have a reg property, so remove the address from the
unit name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
l2-cache which is either an aurora-outer-cache or an aurora-system-cache
has a reg property so the unit name should contain an address.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
PCIe has a ranges property, so the unit name should contain an address.
Take the opportunity to use the node label instead of the full name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
PCIe has a range property, so the unit name should contain an address.
Take the opportunity to use the node label instead of the full name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
