On some systems the sdhci capabilty register is incorrect for one
reason or another.
The sdhci-caps-mask property specifies which bits in the register
are incorrect and should be turned off before using sdhci-caps to turn
on bits.
The sdhci-caps property specifies which bits should be turned on.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Nexbox A95X exists with a Meson GXBB (S905) Soc or a Meson GXL SoC (S905X).
Add the S905X variant which uses the internal PHY instead of an external PHY.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add support for the Nexbox A1 board based on the Amlogic S912 SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[khilman: replace '_' in node-names with '-']
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
RGMII requires special RX and/or TX delays depending on the actual
hardware circuit/wiring. These delays can be added by the MAC, the PHY
or the designer of the circuit (the latter means that no delay has to
be added by PHY or MAC).
There are 4 RGMII phy-modes used describe where a delay should be
applied:
- rgmii: the RX and TX delays are either added by the MAC (where the
exact delay is typically configurable, and can be turned off when no
extra delay is needed) or not needed at all (because the hardware
wiring adds the delay already). The PHY should neither add the RX nor
TX delay in this case.
- rgmii-rxid: configures the PHY to enable the RX delay. The MAC should
not add the RX delay in this case.
- rgmii-txid: configures the PHY to enable the TX delay. The MAC should
not add the TX delay in this case.
- rgmii-id: combines rgmii-rxid and rgmii-txid and thus configures the
PHY to enable the RX and TX delays. The MAC should neither add the RX
nor TX delay in this case.
Document these cases in the ethernet.txt documentation to make it clear
when to use each mode.
If applied incorrectly one might end up with MAC and PHY both enabling
for example the TX delay, which breaks ethernet TX traffic on 1000Mbit/s
links.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chanwoo writes:
Update extcon for 4.10
Detailed description for this pull request:
- The extcon-usb-gpio driver supports the VBUS detection with USB ID and VBUS pin.
Kishon writes:
phy: for 4.10
Merge contains:
*) Add new usb2 phy driver for Meson8b and GXBB
*) Remove phy drivers added for miphy365 and STiH415/6 (as support for
these SoCs are removed from the kernel)
*) Add a sysfs entry to facilitate usb role swap in rcar SoC
*) Add support for otg port in rk3399
*) misc fixes in various phy drivers and cleanups
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The i.MX6UL internal touchscreen controller contains an option to
average upon samples. This feature reduces noise from the produced
touch locations.
This patch adds sample averaging support to the imx6ul_tsc device
driver.
Signed-off-by: Guy Shapiro <guy.shapiro@mobi-wize.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Newly added support of TPM 2.0 eventlog securityfs pseudo files in tpm
device driver consumes device tree bindings representing I2C based
Physical TPM. This patch adds the documentation for corresponding device
tree bindings of I2C based Physical TPM. These bindings are similar to
vtpm device tree bindings being used on IBM Power7+ and Power8 Systems
running PowerVM.
Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Virtual TPM, which is being used on IBM POWER7+ and POWER8 systems running
POWERVM, is currently supported by tpm device driver but lacks the
documentation. This patch adds the missing documentation for the existing
support.
Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Pull "This device-tree pxa update brings" from Robert Jarzmik:
- pxa25x support
- cpu operating points in preparation for cpufreq-dt
- small fixes
* tag 'pxa-dt-4.10' of https://github.com/rjarzmik/linux:
ARM: dts: pxa: add pxa27x cpu operating points
ARM: dts: pxa: add pxa25x cpu operating points
ARM: dts: pxa: fix gpio0 and gpio1 interrupts
ARM: dts: pxa: fix no. of gpio cells in the pxa gpio binding documentation
ARM: dts: pxa: add pxa25x .dtsi file
Pull "ARM: OXNAS SoC DT updates for 4.10" from Neil Armstrong:
- Add DTSI for Oxford Semiconductor OX820
- Add DTS for Cloud Engines PogoPlug v3 board
- Fix MAINTAINERS Oxnas entry for dts files
from http://lkml.kernel.org/r/20161102141850.25164-1-narmstrong@baylibre.com
* tag 'oxnas-arm-soc-dt-for-4.10' of https://github.com/OXNAS/linux:
MAINTAINERS: oxnas: Add new files definitions
ARM: dts: Add support for OX820 and Pogoplug V3
Add support for the MSM8996/APQ8096 PCIe controller. MSM8996 supports Gen
1/2, one lane, 3 PCIe root complexes with support for MSI and legacy
interrupts, and it conforms to PCI Express Base 2.1 specification.
Add a post_init callback to qcom_pcie_ops, as the PCIe pipe clocks are only
setup after the phy is powered on. It also adds an ltssm_enable callback
as it is very much different from other supported SoCs in the driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
The AM571x-IDK board is a board based on TI's AM5718 SOC
which has a single core 1.5GHz A15 processor. This board is a
development platform for the Industrial market with:
- 1GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector
The link to the data sheet and TRM can be found here:
http://www.ti.com/product/AM5718
Initial support is only for basic peripherals.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Following the Amlogic Linux kernel, it seem the only differences
between the GXL and GXM SoCs are the CPU Clusters.
This commit renames the gxl-s905d-p23x DTSI in a common file for
S905D p23x and S912 q20x boards.
Then adds a meson-gxm dtsi and reproduce the P23x to Q20x boards
dts files since the S905D and S912 SoCs shares the same pinout
and the P23x and Q20x boards are identical.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add device tree binding documentation for the Product Register (PRR),
which provides product and revision information on most Renesas ARM
SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ath.git patches for 4.10. Major changes:
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
"rockchip,hw-tshut-temp", "rockchip,hw-tshut-mode" and
"rockchip,hw-tshut-polarity" are not a required properties
actually as the code could also work by loading the default
settings there. So it is apprently misleading, although we
prefer to get these from DT. And it seems we miss the 'rockchip,grf'
here which should also be an optional property.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal codec on A23/A33/H3 is split into 2 parts. The
analog path controls are routed through an embedded custom register
bus accessed through the PRCM block.
The SoCs share a common set of inputs, outputs, and audio paths.
The following table lists the differences.
----------------------------------------
| Feature \ SoC | A23 | A33 | H3 |
----------------------------------------
| Headphone | v | v | |
----------------------------------------
| Line Out | | | v |
----------------------------------------
| Phone In/Out | v | v | |
----------------------------------------
Add a binding for this hardware.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
With the devices added to the tables, the probe will recognize the
switch. This however is not sufficient to make it work properly, other
changes are needed because of incompatibilities.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCA9632TK part seems to incorrectly blink at ~1.3x of the programmed
rate. This patchset add a nxp,period-scale devicetree property to
adjust for this misconfiguration.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Linux 4.9-rc6
* tag 'v4.9-rc6': (305 commits)
Linux 4.9-rc6
ext4: sanity check the block and cluster size at mount time
fscrypto: don't use on-stack buffer for key derivation
fscrypto: don't use on-stack buffer for filename encryption
i2c: i2c-mux-pca954x: fix deselect enabling for device-tree
kvm: x86: merge kvm_arch_set_irq and kvm_arch_set_irq_inatomic
KVM: x86: fix missed SRCU usage in kvm_lapic_set_vapic_addr
KVM: async_pf: avoid recursive flushing of work items
kvm: kvmclock: let KVM_GET_CLOCK return whether the master clock is in use
KVM: Disable irq while unregistering user notifier
KVM: x86: do not go through vcpu in __get_kvmclock_ns
MAINTAINERS: Add LED subsystem co-maintainer
crypto: algif_hash - Fix NULL hash crash with shash
powerpc/mm: Fix missing update of HID register on secondary CPUs
KVM: arm64: Fix the issues when guest PMCCFILTR is configured
arm64: KVM: pmu: Fix AArch32 cycle counter access
powerpc/mm/radix: Invalidate ERAT on tlbiel for POWER9 DD1
i2c: digicolor: use clk_disable_unprepare instead of clk_unprepare
ipmi/bt-bmc: change compatible node to 'aspeed, ast2400-ibt-bmc'
Revert "drm/mediatek: set vblank_disable_allowed to true"
...
This pull request brings thermal support to the BCM2837 DT, and a few
other fixes.
In order to get the thermal node that we're adjusting the compatible
string on, we have to merge in the bcm2835-dt-next branch.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Pull Exynos5433 SoC updates from Sylwester Nawrocki:
- addition of missing documentation and DT properties for the CMU_AUD
block source clocks,
- correction of CMU_FSYS parent clock definition,
- marking as critical clocks which have to be enabled in order
to access control registers of child CMUs.
* tag 'clk-v4.10-exynos5433' of git://linuxtv.org/snawrocki/samsung:
clk: exynos5433: Mark some clocks as critical
clk: exynos5433: Add documentation for the audio block parent clocks
clk: exynos5433: Fix parent clocks for FSYS block
RK1108 EVB is designed by Rockchip for CVR field.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
[split off from dts patch and to prevent conflicts with px5 addition]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
MSIOF in R-Car M3-W (r8a7796) is handled fine by the existing driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ARM specifies that the system counter "must be implemented in an
always-on power domain," and so we try to use the counter as a source of
timekeeping across suspend/resume. Unfortunately, some SoCs (e.g.,
Rockchip's RK3399) do not keep the counter ticking properly when
switched from their high-power clock to the lower-power clock used in
system suspend. Support this quirk by adding a new device tree property.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Driver can now work with both ID and VBUS pins or either one of
them.
There can be the following 3 cases
1) Both ID and VBUS GPIOs are available:
ID = LOW -> USB_HOST active, USB inactive
ID = HIGH -> USB_HOST inactive, USB state is same as VBUS.
2) Only ID GPIO is available:
ID = LOW -> USB_HOST active, USB inactive
ID = HIGH -> USB_HOST inactive, USB active
3) Only VBUS GPIO is available:
VBUS = LOW -> USB_HOST inactive, USB inactive
VBUS = HIGH -> USB_HOST inactive, USB active
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch adds documentation of device tree bindings for the STM32 ADC.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch derives device tree node from pcie bus layer framework.
Device tree bindings file has been renamed(marvell-sd8xxx.txt ->
marvell-8xxx.txt) to accommodate PCIe changes.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
