This extra check will avoid Broadcast_Channel register related traffic
to many IIDC, SBP-2, and AV/C devices which aren't IRMC or have a
max_rec < 8 (i.e. support < 512 bytes async payload). This avoids a
little bit of traffic after bus reset and is even more careful with
devices which don't implement this CSR.
The assumption is that no other protocol than IP over 1394 uses the
broadcast channel for streams.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Fix kernel-doc warnings in linux/irq.h:
Warning(include/linux/irq.h:201): No description found for parameter 'node'
Warning(include/linux/irq.h:201): Excess struct/union/enum/typedef member 'cpu' description in 'irq_desc'
Warning(include/linux/irq.h:434): No description found for parameter 'node'
Warning(include/linux/irq.h:434): Excess function parameter 'cpu' description in 'alloc_desc_masks'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
LKML-Reference: <4A3467EC.50006@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The Toshiba parts all have a 24 MHz HCLK, but HTC ASIC3 has a 24.576 MHz HCLK
and AMD Imageon w228x's HCLK is 80 MHz. With this patch, the MFD driver
provides the HCLK frequency to tmio_mmc via mfd_cell->driver_data.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The code is divided in two parts. There is a virtual 'bus' driver
that handles PCI device and registers three new devices one per card
reader type. The other driver handles SD/MMC part of the reader.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: Fix oops on unaligned user access
avr32: Add support for Mediama RMTx add-on board for ATNGW100
avr32: Change Atmel ATNGW100 config to add choice of add-on board
Fix MIMC200 board LCD init
avr32: Fix clash in ATMEL_USART_ flags
avr32: remove obsolete hw_interrupt_type
avr32: Solves problem with inverted MCI detect pin on Merisc board
atmel-mci: Add support for inverted detect pin
General description: kmemcheck is a patch to the linux kernel that
detects use of uninitialized memory. It does this by trapping every
read and write to memory that was allocated dynamically (e.g. using
kmalloc()). If a memory address is read that has not previously been
written to, a message is printed to the kernel log.
Thanks to Andi Kleen for the set_memory_4k() solution.
Andrew Morton suggested documenting the shadow member of struct page.
Signed-off-by: Vegard Nossum <vegardno@ifi.uio.no>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
[export kmemcheck_mark_initialized]
[build fix for setup_max_cpus]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegardno@ifi.uio.no>
This patch adds the hlist_nulls_add_head() function which is
based on hlist_nulls_add_head_rcu() but without the use of
rcu_assign_pointer(). It also adds hlist_nulls_del which is
exactly the same like hlist_nulls_del_rcu().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
commit 3f68535ada (clocksource: sanity check sysfs clocksource
changes) prevents selection of non high resolution capable
clocksources when high resolution mode is active, but did not take
into account that the same rules apply for highres=off nohz=on.
Check the tick device mode instead of hrtimer_hres_active() to verify
whether the system needs to be protected from a switch to jiffies or
other non highres capable clock sources.
Reported-by: Luming Yu <luming.yu@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is sometimes a need for the ocores driver to add devices to the
bus when installed.
i2c_register_board_info can not always be used, because the I2C devices
are not known at an early state, they could for instance be connected
on a I2C bus on a PCI device which has the Open Cores IP.
i2c_new_device can not be used in all cases either since the resulting
bus nummer might be unknown.
The solution is the pass a list of I2C devices in the platform data to
the Open Cores driver. This is useful for MFD drivers.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Rationale: kmemcheck needs to be able to schedule a tasklet without
touching any dynamically allocated memory _at_ _all_ (since that would
lead to a recursive page fault). This tasklet is used for writing the
error reports to the kernel log.
The new scheduling function avoids touching any other tasklets by
inserting the new tasklist as the head of the "tasklet_hi" list instead
of on the tail.
Also don't wake up the softirq thread lest the scheduler access some
tracked memory and we go down with a recursive page fault.
In this case, we'd better just wait for the maximum time of 1/HZ for the
message to appear.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (50 commits)
drm: include kernel list header file in hashtab header
drm: Export hash table functionality.
drm: Split out the mm declarations in a separate header. Add atomic operations.
drm/radeon: add support for RV790.
drm/radeon: add rv740 drm support.
drm_calloc_large: check right size, check integer overflow, use GFP_ZERO
drm: Eliminate magic I2C frobbing when reading EDID
drm/i915: duplicate desired mode for use by fbcon.
drm/via: vfree() no need checking before calling it
drm: Replace DRM_DEBUG with DRM_DEBUG_DRIVER in i915 driver
drm: Replace DRM_DEBUG with DRM_DEBUG_MODE in drm_mode
drm/i915: Replace DRM_DEBUG with DRM_DEBUG_KMS in intel_sdvo
drm/i915: replace DRM_DEBUG with DRM_DEBUG_KMS in intel_lvds
drm: add separate drm debugging levels
radeon: remove _DRM_DRIVER from the preadded sarea map
drm: don't associate _DRM_DRIVER maps with a master
drm: simplify kcalloc() call to kzalloc().
intelfb: fix spelling of "CLOCK"
drm: fix LOCK_TEST_WITH_RETURN macro
drm/i915: Hook connector to encoder during load detection (fixes tv/vga detect)
...
Move
arch/x86/kernel/acpi/boot.c: acpi_parse_mcfg()
to
arch/x86/pci/mmconfig-shared.c: pci_parse_mcfg()
where it is used, and make it static.
Move associated globals and helper routine with it.
No functional change.
This code move is in preparation for SFI support,
which will allow the PCI code to find the MCFG table
on systems which do not support ACPI.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This will help kmemcheck (and possibly other debugging tools) since we
can now simply pass regs->bp to the stack tracer instead of specifying
the number of stack frames to skip, which is unreliable if gcc decides
to inline functions, etc.
Note that this makes the API incomplete for other architectures, but I
expect that those can be updated lazily, e.g. when they need it.
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: use more NOFS allocation
dlm: connect to nodes earlier
dlm: fix use count with multiple joins
dlm: Make name input parameter of {,dlm_}new_lockspace() const
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_counter: Start documenting HAVE_PERF_COUNTERS requirements
perf_counter: Add forward/backward attribute ABI compatibility
perf record: Explicity program a default counter
perf_counter: Remove PERF_TYPE_RAW special casing
perf_counter: PERF_TYPE_HW_CACHE is a hardware counter too
powerpc, perf_counter: Fix performance counter event types
perf_counter/x86: Add a quirk for Atom processors
perf_counter tools: Remove one L1-data alias
git commit 0a0c5168 "PM: Introduce functions for suspending and resuming
device interrupts" introduced some helper functions. However these
functions are only available for architectures which support
GENERIC_HARDIRQS.
Other architectures will see this build error:
drivers/built-in.o: In function `sysdev_suspend':
(.text+0x15138): undefined reference to `check_wakeup_irqs'
drivers/built-in.o: In function `device_power_up':
(.text+0x1cb66): undefined reference to `resume_device_irqs'
drivers/built-in.o: In function `device_power_down':
(.text+0x1cb92): undefined reference to `suspend_device_irqs'
To fix this add some empty inline functions for !GENERIC_HARDIRQS.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The *_nvs_* routines in swsusp.c make use of the io*map()
functions, which are only provided for HAS_IOMEM, thus
breaking compilation if HAS_IOMEM is not set. Fix this
by moving the *_nvs_* routines into hibernate_nvs.c, which
is only compiled if HAS_IOMEM is set.
[rjw: Change the name of the new file to hibernate_nvs.c, add the
license line to the header comment.]
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch removes the legacy callbacks ->suspend() and
->resume() from struct device_type. These callbacks seem
unused, and new code should instead make use of struct
dev_pm_ops.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Remove the ->suspend_late() and ->resume_early() callbacks
from struct bus_type V2. These callbacks are legacy stuff
at this point and since there seem to be no in-tree users
we may as well remove them. New users should use dev_pm_ops.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1241) renames a bunch of functions in the PM core.
Rather than go through a boring list of name changes, suffice it to
say that in the end we have a bunch of pairs of functions:
device_resume_noirq dpm_resume_noirq
device_resume dpm_resume
device_complete dpm_complete
device_suspend_noirq dpm_suspend_noirq
device_suspend dpm_suspend
device_prepare dpm_prepare
in which device_X does the X operation on a single device and dpm_X
invokes device_X for all devices in the dpm_list.
In addition, the old dpm_power_up and device_resume_noirq have been
combined into a single function (dpm_resume_noirq).
Lastly, dpm_suspend_start and dpm_resume_end are the renamed versions
of the former top-level device_suspend and device_resume routines.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Rename the functions performing "_noirq" dev_pm_ops
operations from device_power_down() and device_power_up()
to device_suspend_noirq() and device_resume_noirq().
The new function names are chosen to show that the functions
are responsible for calling the _noirq() versions to finalize
the suspend/resume operation. The current function names do
not perform power down/up anymore so the names may be misleading.
Global function renames:
- device_power_down() -> device_suspend_noirq()
- device_power_up() -> device_resume_noirq()
Static function renames:
- suspend_device_noirq() -> __device_suspend_noirq()
- resume_device_noirq() -> __device_resume_noirq()
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Len Brown <lenb@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (290 commits)
ALSA: pcm - Update document about xrun_debug proc file
ALSA: lx6464es - support standard alsa module parameters
ALSA: snd_usb_caiaq: set mixername
ALSA: hda - add quirk for STAC92xx (SigmaTel STAC9205)
ALSA: use card device as parent for jack input-devices
ALSA: sound/ps3: Correct existing and add missing annotations
ALSA: sound/ps3: Restructure driver source
ALSA: sound/ps3: Fix checkpatch issues
ASoC: Fix lm4857 control
ALSA: ctxfi - Clear PCM resources at hw_params and hw_free
ALSA: ctxfi - Check the presence of SRC instance in PCM pointer callbacks
ALSA: ctxfi - Add missing start check in atc_pcm_playback_start()
ALSA: ctxfi - Add use_system_timer module option
ALSA: usb - Add boot quirk for C-Media 6206 USB Audio
ALSA: ctxfi - Fix wrong model id for UAA
ALSA: ctxfi - Clean up probe routines
ALSA: hda - Fix the previous tagra-8ch patch
ALSA: hda - Add 7.1 support for MSI GX620
ALSA: pcm - A helper function to compose PCM stream name for debug prints
ALSA: emu10k1 - Fix minimum periods for efx playback
...
* 'topic/slab/earlyboot-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
slab: setup cpu caches later on when interrupts are enabled
slab,slub: don't enable interrupts during early boot
slab: fix gfp flag in setup_cpu_cache()
x86: make zap_low_mapping could be used early
irq: slab alloc for default irq_affinity
memcg: fix page_cgroup fatal error in FLATMEM
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (154 commits)
[SCSI] osd: Remove out-of-tree left overs
[SCSI] libosd: Use REQ_QUIET requests.
[SCSI] osduld: use filp_open() when looking up an osd-device
[SCSI] libosd: Define an osd_dev wrapper to retrieve the request_queue
[SCSI] libosd: osd_req_{read,write} takes a length parameter
[SCSI] libosd: Let _osd_req_finalize_data_integrity receive number of out_bytes
[SCSI] libosd: osd_req_{read,write}_kern new API
[SCSI] libosd: Better printout of OSD target system information
[SCSI] libosd: OSD2r05: Attribute definitions
[SCSI] libosd: OSD2r05: Additional command enums
[SCSI] mpt fusion: fix up doc book comments
[SCSI] mpt fusion: Added support for Broadcast primitives Event handling
[SCSI] mpt fusion: Queue full event handling
[SCSI] mpt fusion: RAID device handling and Dual port Raid support is added
[SCSI] mpt fusion: Put IOC into ready state if it not already in ready state
[SCSI] mpt fusion: Code Cleanup patch
[SCSI] mpt fusion: Rescan SAS topology added
[SCSI] mpt fusion: SAS topology scan changes, expander events
[SCSI] mpt fusion: Firmware event implementation using seperate WorkQueue
[SCSI] mpt fusion: rewrite of ioctl_cmds internal generated function
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-lguest: (31 commits)
lguest: add support for indirect ring entries
lguest: suppress notifications in example Launcher
lguest: try to batch interrupts on network receive
lguest: avoid sending interrupts to Guest when no activity occurs.
lguest: implement deferred interrupts in example Launcher
lguest: remove obsolete LHREQ_BREAK call
lguest: have example Launcher service all devices in separate threads
lguest: use eventfds for device notification
eventfd: export eventfd_signal and eventfd_fget for lguest
lguest: allow any process to send interrupts
lguest: PAE fixes
lguest: PAE support
lguest: Add support for kvm_hypercall4()
lguest: replace hypercall name LHCALL_SET_PMD with LHCALL_SET_PGD
lguest: use native_set_* macros, which properly handle 64-bit entries when PAE is activated
lguest: map switcher with executable page table entries
lguest: fix writev returning short on console output
lguest: clean up length-used value in example launcher
lguest: Segment selectors are 16-bit long. Fix lg_cpu.ss1 definition.
lguest: beyond ARRAY_SIZE of cpu->arch.gdt
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-virtio:
virtio: enhance id_matching for virtio drivers
virtio: fix id_matching for virtio drivers
virtio: handle short buffers in virtio_rng.
virtio_blk: add missing __dev{init,exit} markings
virtio: indirect ring entries (VIRTIO_RING_F_INDIRECT_DESC)
virtio: teach virtio_has_feature() about transport features
virtio: expose features in sysfs
virtio_pci: optional MSI-X support
virtio_pci: split up vp_interrupt
virtio: find_vqs/del_vqs virtio operations
virtio: add names to virtqueue struct, mapping from devices to queues.
virtio: meet virtio spec by finalizing features before using device
virtio: fix obsolete documentation on probe function
* 'cuse' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
CUSE: implement CUSE - Character device in Userspace
fuse: export symbols to be used by CUSE
fuse: update fuse_conn_init() and separate out fuse_conn_kill()
fuse: don't use inode in fuse_file_poll
fuse: don't use inode in fuse_do_ioctl() helper
fuse: don't use inode in fuse_sync_release()
fuse: create fuse_do_open() helper for CUSE
fuse: clean up args in fuse_finish_open() and fuse_release_fill()
fuse: don't use inode in helpers called by fuse_direct_io()
fuse: add members to struct fuse_file
fuse: prepare fuse_direct_io() for CUSE
fuse: clean up fuse_write_fill()
fuse: use struct path in release structure
fuse: misc cleanups
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-module-and-param:
module: cleanup FIXME comments about trimming exception table entries.
module: trim exception table on init free.
module: merge module_alloc() finally
uml module: fix uml build process due to this merge
x86 module: merge the rest functions with macros
x86 module: merge the same functions in module_32.c and module_64.c
uvesafb: improve parameter handling.
module_param: allow 'bool' module_params to be bool, not just int.
module_param: add __same_type convenience wrapper for __builtin_types_compatible_p
module_param: split perm field into flags and perm
module_param: invbool should take a 'bool', not an 'int'
cyber2000fb.c: use proper method for stopping unload if CONFIG_ARCH_SHARK
* 'for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (29 commits)
ide: re-implement ide_pci_init_one() on top of ide_pci_init_two()
ide: unexport ide_find_dma_mode()
ide: fix PowerMac bootup oops
ide: skip probe if there are no devices on the port (v2)
sl82c105: add printk() logging facility
ide-tape: fix proc warning
ide: add IDE_DFLAG_NIEN_QUIRK device flag
ide: respect quirk_drives[] list on all controllers
hpt366: enable all quirks for devices on quirk_drives[] list
hpt366: sync quirk_drives[] list with pdc202xx_{new,old}.c
ide: remove superfluous SELECT_MASK() call from do_rw_taskfile()
ide: remove superfluous SELECT_MASK() call from ide_driveid_update()
icside: remove superfluous ->maskproc method
ide-tape: fix IDE_AFLAG_* atomic accesses
ide-tape: change IDE_AFLAG_IGNORE_DSC non-atomically
pdc202xx_old: kill resetproc() method
pdc202xx_old: don't call pdc202xx_reset() on IRQ timeout
pdc202xx_old: use ide_dma_test_irq()
ide: preserve Host Protected Area by default (v2)
ide-gd: implement block device ->set_capacity method (v2)
...
As explained by Benjamin Herrenschmidt:
Oh and btw, your patch alone doesn't fix powerpc, because it's missing
a whole bunch of GFP_KERNEL's in the arch code... You would have to
grep the entire kernel for things that check slab_is_available() and
even then you'll be missing some.
For example, slab_is_available() didn't always exist, and so in the
early days on powerpc, we used a mem_init_done global that is set form
mem_init() (not perfect but works in practice). And we still have code
using that to do the test.
Therefore, mask out __GFP_WAIT, __GFP_IO, and __GFP_FS in the slab allocators
in early boot code to avoid enabling interrupts.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Conflicts:
drivers/message/fusion/mptsas.c
fixed up conflict between req->data_len accessors and mptsas driver updates.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is a followup patch to the one implemeting rdesc representation in debugfs
rather than being dependent on compile-time CONFIG_HID_DEBUG setting.
The API of the appropriate formatting functions is slightly modified -- if
they are passed seq_file pointer, the one-shot output for 'rdesc' file mode
is used, and therefore the message is formatted into the corresponding seq_file
immediately.
Otherwise the called function allocated a new buffer, formats the text into the
buffer and returns the pointer to it, so that it can be queued into the ring-buffer
of the processess blocked waiting on input on 'events' file in debugfs.
'debug' parameter to the 'hid' module is now used solely for the prupose of inetrnal
driver state debugging (parser, transport, etc).
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is a little bit inconvenient for people who have some non-standard
HID hardware (usually violating the HID specification) to have to
recompile kernel with CONFIG_HID_DEBUG to be able to see kernel's perspective
of the HID report descriptor and observe the parsed events. Plus the messages
are then mixed up inconveniently with the rest of the dmesg stuff.
This patch implements /sys/kernel/debug/hid/<device>/rdesc file, which
represents the kernel's view of report descriptor (both the raw report
descriptor data and parsed contents).
With all the device-specific debug data being available through debugfs, there
is no need for keeping CONFIG_HID_DEBUG, as the 'debug' parameter to the
hid module will now only output only driver-specific debugging options, which has
absolutely minimal memory footprint, just a few error messages and one global
flag (hid_debug).
We use the current set of output formatting functions. The ones that need to be
used both for one-shot rdesc seq_file and also for continuous flow of data
(individual reports, as being sent by the device) distinguish according to the
passed seq_file parameter, and if it is NULL, it still output to kernel ringbuffer,
otherwise the corresponding seq_file is used for output.
The format of the output is preserved.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We no longer need an efficient mechanism to force the Guest back into
host userspace, as each device is serviced without bothering the main
Guest process (aka. the Launcher).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Currently, when a Guest wants to perform I/O it calls LHCALL_NOTIFY with
an address: the main Launcher process returns with this address, and figures
out what device to run.
A far nicer model is to let processes bind an eventfd to an address: if we
find one, we simply signal the eventfd.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Davide Libenzi <davidel@xmailserver.org>
lguest never checked for pending interrupts when enabling interrupts, and
things still worked. However, it makes a significant difference to TCP
performance, so it's time we fixed it by introducing a pending_irq flag
and checking it on irq_restore and irq_enable.
These two routines are now too big to patch into the 8/10 bytes
patch space, so we drop that code.
Note: The high latency on interrupt delivery had a very curious
effect: once everything else was optimized, networking without GSO was
faster than networking with GSO, since more interrupts were sent and
hence a greater chance of one getting through to the Guest!
Note2: (Almost) Closing the same loophole for iret doesn't have any
measurable effect, so I'm leaving that patch for the moment.
Before:
1GB tcpblast Guest->Host: 30.7 seconds
1GB tcpblast Guest->Host (no GSO): 76.0 seconds
After:
1GB tcpblast Guest->Host: 6.8 seconds
1GB tcpblast Guest->Host (no GSO): 27.8 seconds
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Add a new feature flag for indirect ring entries. These are ring
entries which point to a table of buffer descriptors.
The idea here is to increase the ring capacity by allowing a larger
effective ring size whereby the ring size dictates the number of
requests that may be outstanding, rather than the size of those
requests.
This should be most effective in the case of block I/O where we can
potentially benefit by concurrently dispatching a large number of
large requests. Even in the simple case of single segment block
requests, this results in a threefold increase in ring capacity.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Drivers don't add transport features to their table, so we
shouldn't check these with virtio_check_driver_offered_feature().
We could perhaps add an ->offered_feature() virtio_config_op,
but that perhaps that would be overkill for a consitency check
like this.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This implements optional MSI-X support in virtio_pci.
MSI-X is used whenever the host supports at least 2 MSI-X
vectors: 1 for configuration changes and 1 for virtqueues.
Per-virtqueue vectors are allocated if enough vectors
available.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (+ whitespace, style)
