Add support for communicating with a Sonics Silicon Backplane through a
SDIO interface, as found in the Nintendo Wii WLAN daughter card.
The Nintendo Wii WLAN card includes a custom Broadcom 4318 chip with
a SDIO host interface.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a sparse warning in the hardware-TKIP code:
drivers/net/wireless/b43/xmit.c:272:18: warning: incorrect type in assignment (different base types)
drivers/net/wireless/b43/xmit.c:272:18: expected unsigned short [unsigned] [short] <noident>
drivers/net/wireless/b43/xmit.c:272:18: got restricted unsigned short [usertype] <noident>
The code should work correctly with and without this patch applied.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when QoS-disable is requested, we would leave QoS enabled
in firmware, but only queue frames on one queue.
Change that and also tell firmware about disabled QoS, so it
completely ignores all the QoS parameters. Also don't upload the parameters,
if QoS is disabled.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calculated values for the ACK timeout and ACK
consume time are different then the values as
used by the Legacy drivers.
After testing from James Ledwith it appeared that
the calculated values caused a high amount of TX
failures, and the values from the Legacy drivers
were the most optimal to prevent TX failure due to
excessive retries.
The symptoms of this problem:
- Rate control module always falls back to 1Mbs
- Low throughput when bitrate was fixed
Possible side-effects (not confirmed but highly likely)
- Problems with DHCP
- Broken connections due to lack of probe response
This should fix at least:
Kernel bugzilla reports: [13362], [13009], [9273]
Fedora bugzilla reports: [443203]
but possible some additional bugs as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andy Whitcroft reported an oops in aoe triggered by use of an
incorrectly initialised request_queue object:
[ 2645.959090] kobject '<NULL>' (ffff880059ca22c0): tried to add
an uninitialized object, something is seriously wrong.
[ 2645.959104] Pid: 6, comm: events/0 Not tainted 2.6.31-5-generic #24-Ubuntu
[ 2645.959107] Call Trace:
[ 2645.959139] [<ffffffff8126ca2f>] kobject_add+0x5f/0x70
[ 2645.959151] [<ffffffff8125b4ab>] blk_register_queue+0x8b/0xf0
[ 2645.959155] [<ffffffff8126043f>] add_disk+0x8f/0x160
[ 2645.959161] [<ffffffffa01673c4>] aoeblk_gdalloc+0x164/0x1c0 [aoe]
The request queue of an aoe device is not used but can be allocated in
code that does not sleep.
Bruno bisected this regression down to
cd43e26f07
block: Expose stacked device queues in sysfs
"This seems to generate /sys/block/$device/queue and its contents for
everyone who is using queues, not just for those queues that have a
non-NULL queue->request_fn."
Addresses http://bugs.launchpad.net/bugs/410198
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13942
Note that embedding a queue inside another object has always been
an illegal construct, since the queues are reference counted and
must persist until the last reference is dropped. So aoe was
always buggy in this respect (Jens).
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Bruno Premont <bonbons@linux-vserver.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The function res_size in drivers/net/niu.c is a copy of resource_size in
linux/ioport.h. Remove the function and use resource_size instead.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the reordered init order, the rtc device is not registered until
later, while sh_rtc_irq_set_freq() was attempting to assign ->irq_freq
directly, resulting in an oops. This is handled by the upper layers for
us, so just kill off the problematic dereference completely.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for execution of an _INI method at the namespace root.
Although not defined in the ACPI specification, this support was
added to Windows around the Vista timeframe. It is added here
for Windows compatibility.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a possible memory leak in the interpreter for package
objects if the package initializer list is longer than the
defined size of the package. This apparently can only happen
if the BIOS changes the package size on the fly (seen in a _PSS
object), as both iASL and the other compiler do not allow this.
The interpreter will truncate the package to the defined size
(and issue an error message), but can leave the extra objects
undeleted if they have been pre-created during the argument
processing (such is the case if the package consists of a number
of sub-packages as in the _PSS.) ACPICA BZ 805.
http://www.acpica.org/bugzilla/show_bug.cgi?id=805
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix for non-ncq & ncq commands causing timeouts when both are issued
simultaneously to the same device.
Signed-off-by: Ashish Kalra <Ashish.Kalra@freescale.com>
[fixed to be actual compileable C code -jg]
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This small patch is just adding the information for PMP spec 1.2
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_tf_read_block() has off-by-one error when converting CHS address
to LBA. The bug isn't very visible because ata_tf_read_block() is
used only when generating sense data for a failed RW command and CHS
addressing isn't used too often these days.
This problem was spotted by Atsushi Nemoto.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It turns out ASUS M2A-VM isn't the only one with the 32bit DMA
problem. Make ahci_asus_m2a_vm_32bit_only() more generic using the
new dmi_get_date() and rename it to ahci_sb600_32bit_only(). Cut off
date is now pointed to by dmi_system_id->driver_data in "yyyymmdd"
format and it's now also allowed to be omitted.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Sandor Bodo-Merle <sbodomerle@gmail.com>
Cc: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There are cases where full date information is required instead of
just the year. Add month and day parsing to dmi_get_year() and rename
it to dmi_get_date().
As the original function only required '/' followed by any number of
parseable characters at the end of the string, keep that behavior to
avoid upsetting existing users.
The new function takes dates of format [mm[/dd]]/yy[yy]. Year, month
and date are checked to be in the ranges of [1-9999], [1-12] and
[1-31] respectively and any invalid or out-of-range component is
returned as zero.
The dummy implementation is updated accordingly but the return value
is updated to indicate field not found which is consistent with how
other dummy functions behave.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Year parsing in dmi_get_year() had the following two bugs.
* "00" is treated as invalid instead of 2000 because zero return from
simple_strtoul() is treated as error.
* "0N" where N >= 8 is treated as invalid of 200N because the leading
0 is considered to specify octal.
Fix the above two bugs by using endptr to detect invalid number and
forcing decimal.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_scsi_pass_thru() was checking for input sanity and disallowed
commands while initializaing qc from scmd. TPM filtering was added
right after protocol check at which point tf wasn't initialized
properly. This means that TPM filtering has never really worked.
This patch fixes the bug by reorganizing ata_scsi_pass_thru() such
that qc is fully initialized before checking for invalid conditions
which is way less error prone.
Discovered while Thilo-Alexander Ginkel was trying debug patches for
bko#13416.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Thilo-Alexander Ginkel <thilo@ginkel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
During introduction of slave_link, sata_sis slipped through the crack
and left with ad-hoc merged SCR access. As SCR status was shared for
both the master and slave devices, when only one of the device is
online, libata EH would think both are online but would only get valid
device signature for the actually present one, which in turn trigger
the probing safety net mechanism and make EH retry causing large delay
during boot. This patch converts sata_sis to slave_link mechanism.
This bug was reported by TAXI in bko#14075.
http://bugzilla.kernel.org/show_bug.cgi?id=14075
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: TAXI <taxi@a-city.de>
Cc: Uwe Koziolek <uwe.koziolek@gmx.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This restriction prevented ASYNC_TX_DMA from being enabled on platform
configurations where DMA address conversion could not be performed in
place on the stack. Since commit 04ce9ab3 ("async_xor: permit callers
to pass in a 'dma/page scribble' region") the async_tx api now either
uses a caller provided 'scribble' buffer, or performs the conversion in
place when sizeof(dma_addr_t) <= sizeof(struct page *).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams wrote:
... DMA-slave clients request specific channels and know the hardware
details at a low level, so it should not be too high an expectation to
push dma mapping responsibility to the client.
Also this patch includes DMA_COMPL_{SRC,DEST}_UNMAP_SINGLE support for
dw_dmac driver.
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use the DMA_SLAVE capability of the DMAEngine API to copy/from a
scatterlist into an arbitrary list of hardware address/length pairs.
This allows a single DMA transaction to copy data from several different
devices into a scatterlist at the same time.
This also adds support to enable some controller-specific features such as
external start and external pause for a DMA transaction.
[dan.j.williams@intel.com: rebased on tx_list movement]
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When using the Freescale DMA controller in external control mode, both the
request count and external pause bits need to be setup correctly. This was
being done with the same function.
The 83xx controller lacks the external pause feature, but has a similar
feature called external start. This feature requires that the request count
bits be setup correctly.
Split the function into two parts, to make it possible to use the external
start feature on the 83xx controller.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
All the necessary fields for handling an ioat2,3 ring entry can fit into
one cacheline. Move ->len prior to ->txd in struct ioat_ring_ent, and
move allocation of these entries to a hw-cache-aligned kmem cache to
reduce the number of cachelines dirtied for descriptor management.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The tx_list attribute of struct dma_async_tx_descriptor is common to
most, but not all dma driver implementations. None of the upper level
code (dmaengine/async_tx) uses it, so allow drivers to implement it
locally if they need it. This saves sizeof(struct list_head) bytes for
drivers that do not manage descriptors with a linked list (e.g.: ioatdma
v2,3).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Drop txx9dmac's use of tx_list from struct dma_async_tx_descriptor in
preparation for removal of this field.
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Drop at_hdmac's use of tx_list from struct dma_async_tx_descriptor in
preparation for removal of this field.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Drop mv_xor's use of tx_list from struct dma_async_tx_descriptor in
preparation for removal of this field.
Cc: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Drop ioatdma's use of tx_list from struct dma_async_tx_descriptor in
preparation for removal of this field.
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Drop iop-adma's use of tx_list from struct dma_async_tx_descriptor in
preparation for removal of this field.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Drop fsldma's use of tx_list from struct dma_async_tx_descriptor in
preparation for removal of this field.
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Drop dw_dmac's use of tx_list from struct dma_async_tx_descriptor in
preparation for removal of this field.
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Trivial cleanup to make the PCI ID table easier to read.
[dan.j.williams@intel.com: extended to v3.2 devices]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The ioatdma module is missing aliases for the PCI devices it supports,
so it is not autoloaded on boot. Add a MODULE_DEVICE_TABLE() to get
these aliases.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The cleanup routine for the raid cases imposes extra checks for handling
raid descriptors and extended descriptors. If the channel does not
support raid it can avoid this extra overhead by using the ioat2 cleanup
path.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jasper Forest introduces raid offload support via ioat3.2 support. When
raid offload is enabled two (out of 8 channels) will report raid5/raid6
offload capabilities. The remaining channels will only report ioat3.0
capabilities (memcpy).
Signed-off-by: Tom Picard <tom.s.picard@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The async_tx api uses the DMA_INTERRUPT operation type to terminate a
chain of issued operations with a callback routine.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If a platform advertises pq capabilities, but not xor, then use
ioat3_prep_pqxor and ioat3_prep_pqxor_val to simulate xor support.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ioat3.2 adds support for raid6 syndrome generation (xor sum of galois
field multiplication products) using up to 8 sources. It can also
perform an pq-zero-sum operation to validate whether the syndrome for a
given set of sources matches a previously computed syndrome.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
