Add did_interrupt() function to check if a PHY port
really caused an interrupt. This is needed in the case
of shared PHY interrupt pin configuration to stop
interrupt event processing for PHY ports which didn't
cause an interrupt.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E1121R Dual PHY device can be hardware-configured
to use shared interrupt pin for both PHY ports. For such
PHY configurations using shared PHY interrupt phy_interrupt()
handler will also schedule a work for PHY port which didn't
cause an interrupt.
This patch adds a possibility for PHY drivers to provide
did_interrupt() function which reports if the PHY (or a PHY
port in a multi-PHY device) generated an interrupt. This
function is called in phy_change() as phy_change() shouldn't
proceed if it is invoked for a PHY which didn't cause an
interrupt. So check for interrupt originator in phy_change()
to allow early-out.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We noticed on parisc that our broadcoms all swapped MAC addresses going
from 2.6.29 to 2.6.30-rc1:
Apr 11 07:48:24 ion kernel: eth0: Tigon3 [partno(BCM95700A6) rev 0105] (PCI:66MHz:64-bit) MAC address 00:30:6e:4b:15:59
Apr 13 07:34:34 ion kernel: eth0: Tigon3 [partno(BCM95700A6) rev 0105] (PCI:66MHz:64-bit) MAC address 00:00:59:15:4b:6e
The problem patch is:
commit 6d348f2c1e
Author: Matt Carlson <mcarlson@broadcom.com>
Date: Wed Feb 25 14:25:52 2009 +0000
tg3: Eliminate tg3_nvram_read_swab()
With the root cause being the use of memcpy to set the mac address:
memcpy(&dev->dev_addr[0], ((char *)&hi) + 2, 2);
memcpy(&dev->dev_addr[2], (char *)&lo, sizeof(lo));
This might work on little endian machines, but it can't on big endian
ones. You have to use the original setting mechanism to be correct on
all architectures.
The attached patch fixes parisc.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a zero address hole bug in the bonding arp_ip_target list
that was causing the bond to ignore ARP replies (bugz 13006).
Instead of just setting the array entry to zero, we now
copy any additional entries down one slot, putting the
zero entry at the end. With this change we can now have
all the loops that walk the array stop when they hit a zero
since there will be no addresses after it.
Changes are based in part on code fragment provided in kernel:
bugzilla 13006:
http://bugzilla.kernel.org/show_bug.cgi?id=13006
by Steve Howard <steve@astutenetworks.com>
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is currently dumping a message in the log about failing to
allocate vf data when max_vfs is equal to 0. This change makes it so the
error message is only displayed if we set max_vfs to a non zero value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igbvbf driver exposed several unused extrnal references due to the fact
that code was copied from igb and then some functionality was removed.
This changes that so that unused functions are either removed or made
static.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were several unused external references added with the sr-iov
enablement changes. This patch changes all those references to static
local references.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC warns:
drivers/net/ixgbe/ixgbe_main.c: In function 'ixgbe_sfp_config_module_task':
drivers/net/ixgbe/ixgbe_main.c:3920: warning: suggest parantheses around
operand of '!' or change '&' to '&&' or '!' to '~'
Which I think is right. Bracket to remove ambiguity.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all physical connection types are being correctly identified. This
fixes that issue, and cleans up the logic to make it more maintainable.
Also clean up the code for device capabilities from the EEPROM to support
multiple SKUs of the same hardware.
Bump the version to reflect all the updates since the 82599 merge.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The orig_autoc variable tracks the original setting of the autonegotiate
state prior to trying a new speed. The usage is inconsistent and not very
maintainable. This patch updates the usage to make it more consistent.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does two things:
1) On 82599, the PHY is emedded in the MAC. On 82598, the SFP+ NIC has an external PHY. The reset in the SFP+ setup patch for 82598 is unnecessary on 82599, and adds extra dead time to device initialization. This removes that PHY reset for 82599 only.
2) On 82599, the SFP+ modules are multispeed fiber modules (10G/1G). We need to make sure to identify them properly for the remaining init sections to properly set them up.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PHY operations are determined, the PHY must be identified. This
identification causes bus access, and should be contained within its own
routines. This also helps the 82599 PHY init paths for both SFP+ and
KX/KX4 devices to be easier to maintain.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The discard pause frames bit was not enabled, so flow control frames could
be passed up to the host. Enabled DPF to keep the frames off the stack.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this warning:
drivers/net/via-velocity.c:1924: warning: passing argument 2 of 'request_irq' from incompatible pointer type
Signed-off-by: Seguier Regis <rseguier@e-teleport.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
All NICs were reporting WOL support when only the KX4 NIC is capable of
supporting WOL. This patch adds a function to check for and exclude all
non-WOL capable nics from enabling WOL in ethtool.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LED blink code is common for 82599 as well. It should be moved to
ixgbe_common.c so both devices can use it, and not have it duplicated.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-mn10300:
Separate out the proc- and unit-specific header directories from the general
Move arch headers from include/asm-mn10300/ to arch/mn10300/include/asm/.
MN10300 arch headers and place them instead in the same directories as contain
the .c files for the processor and unit implementations.
This permits the symlinks include/asm/proc and include/asm/unit to be
dispensed with. This does, however, require that #include <asm/proc/xxx.h> be
converted to #include <proc/xxx.h> and similarly for asm/unit -> unit.
Signed-off-by: David Howells <dhowells@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Add support for new SFP+ PHY
RDMA/nes: Add wide_ppm_offset parm for switch compatibility
RDMA/nes: Fix SFP+ PHY initialization
RDMA/nes: Fix nes_nic_cm_xmit() error handling
RDMA/nes: Fix error handling issues
RDMA/nes: Fix incorrect casts on 32-bit architectures
IPoIB: Document newish features
RDMA/cma: Create cm id even when IB port is down
RDMA/cma: Use rate from IPoIB broadcast when joining IPoIB multicast groups
IPoIB: Avoid free_netdev() BUG when destroying a child interface
mlx4_core: Don't leak mailbox for SET_PORT on Ethernet ports
RDMA/cxgb3: Release dependent resources only when endpoint memory is freed.
RDMA/cxgb3: Handle EEH events
IB/mlx4: Use pgprot_writecombine() for BlueFlame pages
This patch removes the sysfs entry num_vfs which was added to support
enabling pci virtual functions for 82576.
To prevent VFs from loading automatically a module parameter "max_vfs" was
added so that the number of VFs per PF can be limited. This is especially
useful when 4 or more 82576 ports are on the system because otherwise to
load all VFs would result in 8 interface per physical port.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds an igbvf driver to handle virtual functions provided by the
igb driver when SR-IOV has been enabled. A virtual function is a
lightweight pci-e function that supports a single queue and shares
resources with the 82576 physical function contained within the igb
driver.
To spawn virtual functions from the igb driver all that is needed is to
enable CONFIG_PCI_IOV and have an 82576 Ethernet adapter on a system that
supports SR-IOV in the BIOS. The virtual functions will appear after the
interface is loaded.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neither the lm90 driver nor the lm87 driver do support interrupts, so
there is no point in specifying one when declaring the devices.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aligning register offset translation table imporves performance
on rx side.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable multiple rx rings for older NX2031 chip, firmware 3.4.336
or newer supports this feature.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o remove unnecessary length parameter since register access
width is fixed 4 byte.
o remove superfluous pci_read_normalize and pci_write_normalize
functions.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reduces netxen_adapter footprint when rss (msi-x) is disabled.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for asynchronous events from firmware,
received over one of the rx rings.
Add support for event based phy interrupts, enhanced links
status reporting from firmware.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
