General update of defconfig including the following notable changes:
- Enable GPIO access via sysfs on GE Fanuc's PPC9A.
- Enable Highmem support.
- Support for PCMCIA based daughter card.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
U-Boot maps PCI IO at 0xe0300000, while current dts files specify
0xe2000000. This leads to the following oops with CONFIG_8139TOO_PIO=y.
8139too Fast Ethernet driver 0.9.28
Machine check in kernel mode.
Caused by (from SRR1=41000): Transfer error ack signal
Oops: Machine check, sig: 7 [#1]
MPC837x RDB
[...]
NIP [00000900] 0x900
LR [c0439df8] rtl8139_init_board+0x238/0x524
Call Trace:
[cf831d90] [c0439dcc] rtl8139_init_board+0x20c/0x524 (unreliable)
[cf831de0] [c043a15c] rtl8139_init_one+0x78/0x65c
[cf831e40] [c0235250] pci_call_probe+0x20/0x30
[...]
This patch fixes the issue by specifying the correct PCI IO base
address.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Sometimes (e.g. when there are no UEMs attached to a board)
fsl_pq_mdio_find_free() fails to find a spare address for a TBI PHY,
this is because get_phy_id() returns bogus 0x0000ffff values
(0xffffffff is expected), and therefore mdio bus probing fails with
the following message:
fsl-pq_mdio: probe of e0082120.mdio failed with error -16
And obviously ethernet doesn't work after this.
This patch solves the problem by adding tbi-phy node into mdio node,
so that we won't scan for spare addresses, we'll just use a fixed one.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Linux isn't able to detect link changes on ethernet ports that were
used by U-Boot. This is because U-Boot wrongly clears interrupt
polarity bit (INTPOL, 0x400) in the extended status register (EXT_SR,
0x1b) of Marvell PHYs.
There is no easy way for PHY drivers to know IRQ line polarity (we
could extract it from the device tree and pass it to phydevs, but
that'll be quite a lot of work), so for now just reset the PHYs to
their default states.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In switch_mmu_context() if we call steal_context_smp() to get a context
to use we shouldn't fall through and than call steal_context_up(). Doing
so can be problematic in that the 'mm' that steal_context_up() ends up
using will not get marked dirty in the stale_map[] for other CPUs that
might have used that mm. Thus we could end up with stale TLB entries in
the other CPUs that can cause all kinda of havoc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The value of armclk_mask needs to be inverted for use as a mask on
the register value when updating ARM_RATIO.
This is critical for cpufreq support, without it attempts to scale
the frequency of the core trash pretty much the entire clock tree.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
If the requested clock is faster than the parent clock then the
parent clock is the closest we can get to the request so we need
to return that instead of the requested clock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In the s3c_gpiolib_getchip implementation for s3c24xx the check whether a pin is
in the gpio banks range is reversed. Thus the function returns NULL for valid
pins and the gpio chip if its not valid.
As a result gpio states are not saved/restored properly during suspend/resume.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Early Pentium M models use different method for enabling TM2
(per paragraph 13.5.2.3 of the "Intel 64 and IA-32 Architectures
Software Developer's Manual Volume 3A: System Programming Guide,
Part 1").
Tested on the affected Pentium M variant (model == 13).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
fseverities_coverage is never NULL in err_out code path.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
mce_cap_init() and mce_cpu_quirks() can be tagged with __cpuinit.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
"mce argument mce ignored. Please use /sys" message shouldn't
be printed when using "mce" boot option.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
On my legacy Pentium M laptop (Acer Extensa 2900) I get bogus MCE on a cold
boot with CONFIG_X86_NEW_MCE enabled, i.e. (after decoding it with mcelog):
MCE 0
HARDWARE ERROR. This is *NOT* a software problem!
Please contact your hardware vendor
CPU 0 BANK 1 MCG status:
MCi status:
Error overflow
Uncorrected error
Error enabled
Processor context corrupt
MCA: Data CACHE Level-1 UNKNOWN Error
STATUS f200000000000195 MCGSTATUS 0
[ The other STATUS values observed: f2000000000001b5 (... UNKNOWN error)
and f200000000000115 (... READ Error).
To verify that this is not a CONFIG_X86_NEW_MCE bug I also modified
the CONFIG_X86_OLD_MCE code (which doesn't log any MCEs) to dump
content of STATUS MSR before it is cleared during initialization. ]
Since the bogus MCE results in a kernel taint (which in turn disables
lockdep support) don't log boot MCEs on Pentium M (model == 13) CPUs
by default ("mce=bootlog" boot parameter can be be used to get the old
behavior).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'drm-radeon-kms' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (35 commits)
drm/radeon: set fb aperture sizes for framebuffer handoff.
drm/ttm: fix highuser vs dma32 confusion.
drm/radeon: Fix size used for benchmarking BO copies.
drm/radeon: Add radeon.test parameter for running BO GPU copy tests.
drm/radeon/kms: allow interruptible waits for objects.
drm/ttm: powerpc: Fix Highmem cache flushing.
x86: Export kmap_atomic_prot() needed for TTM.
drm/ttm: Fix ttm in-kernel copying of pages with non-standard caching attributes.
drm/ttm: Fix an oops and sync object leak.
drm/radeon/kms: vram sizing on certain r100 chips needs workaround.
drm/radeon: Pay more attention to object placement requested by userspace.
drm/radeon: Fall back to evicting BOs with memcpy if necessary.
drm/radeon: Don't unreserve twice on failure to validate.
drm/radeon/kms: fix bandwidth computation on avivo hardware
drm/radeon/kms: add initial colortiling support.
drm/radeon/kms: fix hotspot handling on pre-avivo chips
drm/radeon/kms: enable frac fb divs on rs600/rs690/rs740
drm/radeon/kms: add PLL flag to prefer frequencies <= the target freq
drm/radeon/kms: block RN50 from using 3D engine.
drm/radeon/kms: fix VRAM sizing like DDX does it.
...
This patch is romImage support for the kfr2r09 board V2.
The partner-jet-setup.txt file is converted into assembly code
which becomes the first code to execute from the reset vector.
The file partner-jet-setup.txt can also be used to setup
the hardware using a JTAG debugger so booting from RAM can
be done without burning the code to flash.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains support for the romImage build target V2.
The resulting romImage file should be burned to rom
or flash and could be used as small boot loader.
Board code should keep their setup code in the file
romimage.h located in their mach include directory.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This cleans up the irqflags tracing code quite a bit and ties it
in to various missing callsites that caused an imbalance when
CONFIG_PROVE_LOCKING was enabled.
Previously this was catching on:
987 #ifdef CONFIG_PROVE_LOCKING
988 DEBUG_LOCKS_WARN_ON(!p->hardirqs_enabled);
989 DEBUG_LOCKS_WARN_ON(!p->softirqs_enabled);
990 #endif
991 retval = -EAGAIN;
with hardirqs being doubly enabled, and subsequently bailing out
with the following call trace:
Call trace:
[<88035224>] __lock_acquire+0x616/0x6a6
[<88015a8c>] do_fork+0xf8/0x2b0
[<880331ec>] trace_hardirqs_on_caller+0xd4/0x114
[<88241074>] _spin_unlock_irq+0x20/0x64
[<88035224>] __lock_acquire+0x616/0x6a6
[<8800386c>] kernel_thread+0x48/0x70
[<88024ecc>] ____call_usermodehelper+0x0/0x110
[<88024ecc>] ____call_usermodehelper+0x0/0x110
[<88003894>] kernel_thread_helper+0x0/0x14
[<88024bac>] __call_usermodehelper+0x38/0x70
[<88025dc0>] worker_thread+0x150/0x274
[<88035b9c>] lock_release+0x0/0x198
[<88024b74>] __call_usermodehelper+0x0/0x70
[<88028cf0>] autoremove_wake_function+0x0/0x30
[<88028bf2>] kthread+0x3e/0x70
[<88025c70>] worker_thread+0x0/0x274
[<8800389c>] kernel_thread_helper+0x8/0x14
[<88028bb4>] kthread+0x0/0x70
[<88003894>] kernel_thread_helper+0x0/0x14
Reported-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reverts commit 1d29ebebcb.
Bumping up the earlytimer initialization causes IRQs to be enabled too
early, which blows up lockdep:
...
NR_IRQS:256 nr_irqs:256
------------[ cut here ]------------
Badness at kernel/lockdep.c:2128
Pid : 0, Comm: swapper
CPU : 0 Not tainted (2.6.31-rc3-00205-g3ed6e12-dirty #2443)
PC is at trace_hardirqs_on_caller+0x48/0x10c
PR is at trace_hardirqs_on_caller+0x3c/0x10c
...
Revert it back to late_time_init time, which fixes up lockdep.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The TLB miss fast-path presently calls in to update_mmu_cache() to
set up the entry, and does so with a NULL vma. Check for vma validity
in the __update_tlb() ptrace checks.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This functionality is needed to kmap_atomic() highmem pages that may
potentially have or are about to set up other mappings with
non-standard caching attributes.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This splits out a separate __update_cache()/__update_tlb() for
update_mmu_cache() to wrap in to. This lets us share the common
__update_cache() bits while keeping special __update_tlb() handling
broken out.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch creates McBSP support on OMAP4430 development platform. This patch
includes corresponding base address changes for OMAP4.
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
- enable PCM043, MX31LILLY, ARMADILLO5X0 and MX35_3DS boards
- enable MXC nand driver
- enable UBI support
- disable cs89x0 support which broke all boards which do not have this chip
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
phys_to_dma() and dma_to_phys() are used instead of
swiotlb_phys_to_bus() and swiotlb_bus_to_phys().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
This adds two functions, phys_to_dma() and dma_to_phys() to x86, IA64
and powerpc. swiotlb uses them. phys_to_dma() converts a physical
address to a dma address. dma_to_phys() does the opposite.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
swiotlb doesn't use swiotlb_arch_address_needs_mapping(); it uses
dma_capalbe(). We can remove unnecessary
swiotlb_arch_address_needs_mapping().
We can remove swiotlb_addr_needs_map() and is_buffer_dma_capable() in
swiotlb_pci_addr_needs_map() too; dma_capable() handles the features
that both provide.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
dma_capable() eventually replaces is_buffer_dma_capable(), which tells
if a memory area is dma-capable or not. The problem of
is_buffer_dma_capable() is that it doesn't take a pointer to struct
device so it doesn't work for POWERPC.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
dma_capable() eventually replaces is_buffer_dma_capable(), which tells
if a memory area is dma-capable or not. The problem of
is_buffer_dma_capable() is that it doesn't take a pointer to struct
device so it doesn't work for POWERPC.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
dma_capable() eventually replaces is_buffer_dma_capable(), which tells
if a memory area is dma-capable or not. The problem of
is_buffer_dma_capable() is that it doesn't take a pointer to struct
device so it doesn't work for POWERPC.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
The first thing sys_truncate() and sys_ftruncate() do is sign extend
the unsigned length arg to a signed type.
Thanks to Benjamin Herrenschmidt for the tip.
Signed-off-by: David S. Miller <davem@davemloft.net>
Startup code for i386 in arch/x86/kernel/head_32.S is using the
reference variable initial_code that is located in the .cpuinit.data
section. If CONFIG_HOTPLUG_CPU is enabled, startup code is not in an
init section and can be called later too. In this case the reference
initial_code must be kept too. This patch fixes this. See below for
the section mismatch warning.
WARNING: vmlinux.o(.cpuinit.data+0x0): Section mismatch in reference
from the variable initial_code to the function
.init.text:i386_start_kernel()
The variable __cpuinitdata initial_code references
a function __init i386_start_kernel().
If i386_start_kernel is only used by initial_code then
annotate i386_start_kernel with a matching annotation.
Signed-off-by: Robert Richter <robert.richter@amd.com>
LKML-Reference: <1248716632-26844-1-git-send-email-robert.richter@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Makefile cleanup
microblaze: Typo fix for cpu param inconsistency
microblaze: Add support for R_MICROBLAZE_64_NONE
microblaze: Get module loading working
microblaze: remove sys_ipc
microblaze: Support unaligned address for put/get_user macros
microblaze: Detect new Microblaze 7.20 versions
microblaze: Fix do_page_fault for no context
microblaze: Add _PAGE_FILE macros to pgtable.h
microblaze: Fix put_user macro for 64bits arguments
microblaze: Clear print messages for DTB passing via r7
microblaze: Not to clear r7 after copying DTB to kernel
microblaze: Add messages about FDT blob
microblaze: Final support for statically linked DTB
microblaze: remove duplicated #include
microblaze: Define tlb_flush macro
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: geode: Mark mfgpt irq IRQF_TIMER to prevent resume failure
x86, amd: Don't probe for extended APIC ID if APICs are disabled
x86, mce: Rename incorrect macro name "CONFIG_X86_THRESHOLD"
x86-64: Fix bad_srat() to clear all state
x86, mce: Fix set_trigger() accessor
x86: Fix movq immediate operand constraints in uaccess.h
x86: Fix movq immediate operand constraints in uaccess_64.h
x86: Add reboot fixup for SBC-fitPC2
x86: Include all of .data.* sections in _edata on 64-bit
x86: Add quirk for Intel DG45ID board to avoid low memory corruption
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] zcrypt: fix scheduling of hrtimer ap_poll_timer
[S390] vdso: clock_gettime of CLOCK_THREAD_CPUTIME_ID with noexec=on
[S390] vdso: fix per cpu area allocation
[S390] hibernation: fix register corruption on machine checks
[S390] hibernation: fix lowcore handling
mm: Pass virtual address to [__]p{te,ud,md}_free_tlb()
Upcoming paches to support the new 64-bit "BookE" powerpc architecture
will need to have the virtual address corresponding to PTE page when
freeing it, due to the way the HW table walker works.
Basically, the TLB can be loaded with "large" pages that cover the whole
virtual space (well, sort-of, half of it actually) represented by a PTE
page, and which contain an "indirect" bit indicating that this TLB entry
RPN points to an array of PTEs from which the TLB can then create direct
entries. Thus, in order to invalidate those when PTE pages are deleted,
we need the virtual address to pass to tlbilx or tlbivax instructions.
The old trick of sticking it somewhere in the PTE page struct page sucks
too much, the address is almost readily available in all call sites and
almost everybody implemets these as macros, so we may as well add the
argument everywhere. I added it to the pmd and pud variants for consistency.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Howells <dhowells@redhat.com> [MN10300 & FRV]
Acked-by: Nick Piggin <npiggin@suse.de>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the SH-4 page clear/copy ops are generic, they can be used for
all platforms with CONFIG_MMU=y. SH-5 remains the odd one out, but it too
will gradually be converted over to using this interface.
SH-3 platforms which do not contain aliases will see no impact from this
change, while aliasing SH-3 platforms will get the same interface as
SH-4.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
