Update defconfig for Zoom2 to include
TWL4030 core
TWL4030 drivers (bci, gpio, keypad, usb, mmc)
Also sync the defconfig after issuing a menuconfig
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For OMAP3 add MMC1 MMC2 pin mux MMC3 mux is not added as there are
multiple configurations possible, so the muxing is left to be done
in board file.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Chikkature Rajashekar <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch makes the SDP boot again with the defconfig.
Changes done:
- Removes other selected boards.
- Sets the Low Level debug output for UART1.
- Disables some paripherals from other boards.
Tested on a SDP3430-VE5.1.0 (OMAP3430 ES3.1)
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This enables to peek the following data.
$ /debug/iommu/isp# ls
mem nr_tlb_entries regs
mmap pagetable tlb
$ /debug/iommu/isp# head pagetable
L: da: pa:
-----------------------------------------
2: 00001000 8ae4a002
2: 00002000 8e7bb002
2: 00003000 8ae49002
2: 00004000 8ae65002
.....
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The second argument should be the end address, not the
length. Actually there will not be any effect on the behavior of this
driver since flush_cache_vmap() calls flush_cache_all() in the end.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add board file for Nokia N800 and N810 devices. Currently only serial ports,
onenand and spi are configured, more to come later.
Tested on Nokia N800.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For some reason usb-tusb6010.c was't compiled, add it to Makefile and
Kconfig. This is prepraration for upcoming n8x0 support.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It is possible for GPIO IRQ lines configured with
falling edge triggering only to get IRQs at the
rising edge upon the exit of offmode. And vice
versa. Prevent such IRQs to arrive by generating
the IRQ obeying the detection scheme.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove left over code for parsing omap boot tags. This is
no longer used.
see commit fc0ef1bfa1353e048e055374a09c75320d22231b
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP tags are deprecrated so drop them.
Drop UART config data which decides which UARTs to enable during boot.
This is no longer necessary since serial core code disables clocks
after inactivity.
Background: with new UART idle code, all on-chip UARTs are idled using
a configurable inactivity timer (default 5 seconds.) After the
inactivity timer, UART clocks are disabled automatically.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Omap tags are deprecated and remove OMAP_TAG_SERIAL_CONSOLE. Console must be
enabled with the console boot parameter instead.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Search and replace OMAP_IO_ADDRESS with OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS,
and convert omap_read/write into a functions instead of a macros.
Also rename OMAP_MPUIO_VBASE to OMAP1_MPUIO_VBASE.
In the long run, most code should use ioremap + __raw_read/write instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This moves the code to start the decrementer on 40x and BookE into
a separate function which is now called from time_init() and
secondary_time_init(), before the respective clock sources are
registered. We also remove the 85xx specific code for doing it
from the platform code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The default COMMAND_LINE_SIZE in asm-generic is 512, so the
net effect of this change is nil, aside from the cleanup
factor. See also commit 2b74b8569.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some of the PCI features we have in ppc32 we will need on ppc64
platforms in the future. These include support for:
* ppc_md.pci_exclude_device
* indirect config cycles
* early config cycles
We also simplified the logic in fake_pci_bus() to assume it will always
get a valid pci_controller. Since all current callers seem to pass it
one.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PCI device tree scanning code in pci_64.c is some useful functionality.
It allows PCI devices to be described in the device tree instead of being
probed for, which in turn allows pci devices to use all of the device tree
facilities to describe complex PCI bus architectures like GPIO and IRQ
routing (perhaps not a common situation for desktop or server systems,
but useful for embedded systems with on-board PCI devices).
This patch moves the device tree scanning into pci-common.c so it is
available for 32-bit powerpc machines too.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We now search through TLBnCFG looking for the first array that has IPROT
support (we assume that there is only one). If that TLB has hardware
entry select (HES) support we use the existing code and with the proper
TLB select (the HES code still needs to clean up bolted entries from
firmware). The non-HES code is pretty similiar to the 32-bit FSL Book-E
code but does make some new assumtions (like that we have tlbilx) and
simplifies things down a bit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Not all 64-bit Book-3E parts will have fixed IVORs so add a function that
cpusetup code can call to setup the base IVORs (0..15) to match the fixed
offsets. We need to 'or' part of interrupt_base_book3e into the IVORs
since on parts that have them the IVPR doesn't extend as far down.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Match what we do on 32-bit Book-E processors and enable the decrementer
in generic_calibrate_decr. We need to make sure we disable the
decrementer early in boot since we currently use lazy (soft) interrupt
on 64-bit Book-E and possible get a decrementer exception before we
are ready for it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move the default cpu entry table for CONFIG_PPC_BOOK3E_64 to the
very end since we will probably want to support both 32-bit and
64-bit kernels for some processors that are higher up in the list.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Support for TLB reservation (or TLB Write Conditional) and Paired MAS
registers are optional for a processor implementation so we handle
them via MMU feature sections.
We currently only used paired MAS registers to access the full RPN + perm
bits that are kept in MAS7||MAS3. We assume that if an implementation has
hardware page table at this time it also implements in TLB reservations.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On POWER6 systems RA needs to be the base and RB the index.
If they are reversed you take a misdirect hit.
Signed-off-by: Mike Wolf <mjwolf@us.ibm.com>
----
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Previously, the 36-bit code was using these bits, but they had
never been named in the pte format definition. This patch just
gives those fields their proper names and adds a comment that
they are only present on some processors.
There is no functional code change.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds max_direct_dma_addr to struct dev_archdata to remove
addr_needs_map in struct dma_mapping_ops. It also converts
dma_capable() to use max_direct_dma_addr.
max_direct_dma_addr is initialized in pci_dma_dev_setup_swiotlb(),
called via ppc_md.pci_dma_dev_setup hook.
For further information:
http://marc.info/?t=124719060200001&r=1&w=2
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The mpc_apic_id setup is handled by a x86_quirk. Make it a
x86_init_ops function with a default implementation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
32bit and also the numaq code have special requirements on the
ioapic_id setup. Convert it to a x86_init_ops function and get rid
of the quirks and #ifdefs
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The x86 quirkification introduced an extra ugly hackery with a
variable pointer in the mpparse code. If the pointer is initialized
then it is dereferenced and the variable set to 0 or incremented.
Create a x86_init_ops function and let the affected numaq code
hold the function. Default init is a setup noop.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
memory_setup is overridden by x86_quirks and by paravirts with weak
functions and quirks. Unify the whole mess and make it an
unconditional x86_init_ops function which defaults to the standard
function and can be overridden by the early platform code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
reserve_ebda_region needs to be called befor start_kernel. Moorestown
needs to override it. Make it a x86_init_ops function and initialize
it with the default reserve_ebda_region.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The 32bit and the 64bit code are slighty different in the reservation
of standard resources. Also the upcoming Moorestown support needs its
own version of that.
Add it to x86_init_ops and initialize it with the 64bit default. 32bit
overrides it in early boot. Now moorestown can add it's own override
w/o sprinkling the code with more #ifdefs
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
