The dai codec needs to ensure that on one dai is used at any time.
This is currently protected by bit atomic operation. With this change,
it done with a mutex instead.
This change is not about functionality or efficiency. It is done with
the hope that it help maintainability in the future.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20191206103542.485224-1-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the datasheet, there are some registers can only be changed
when SHDN is 0. Changing these settings during SHDN = 1 can compromise
device stability and performance specifications.
Saves SHDN before writing to these sensitive registers and restores SHDN
afterward.
Here is the register list codec driver of max98090 wants to change:
M98090_REG_QUICK_SYSTEM_CLOCK 0x04
M98090_REG_QUICK_SAMPLE_RATE 0x05
M98090_REG_DAI_INTERFACE 0x06
M98090_REG_DAC_PATH 0x07
M98090_REG_MIC_DIRECT_TO_ADC 0x08
M98090_REG_LINE_TO_ADC 0x09
M98090_REG_ANALOG_MIC_LOOP 0x0A
M98090_REG_ANALOG_LINE_LOOP 0x0B
M98090_REG_SYSTEM_CLOCK 0x1B
M98090_REG_CLOCK_MODE 0x1C
M98090_REG_CLOCK_RATIO_NI_MSB 0x1D
M98090_REG_CLOCK_RATIO_NI_LSB 0x1E
M98090_REG_CLOCK_RATIO_MI_MSB 0x1F
M98090_REG_CLOCK_RATIO_MI_LSB 0x20
M98090_REG_MASTER_MODE 0x21
M98090_REG_INTERFACE_FORMAT 0x22
M98090_REG_TDM_CONTROL 0x23
M98090_REG_TDM_FORMAT 0x24
M98090_REG_IO_CONFIGURATION 0x25
M98090_REG_FILTER_CONFIG 0x26
M98090_REG_INPUT_ENABLE 0x3E
M98090_REG_OUTPUT_ENABLE 0x3F
M98090_REG_BIAS_CONTROL 0x42
M98090_REG_DAC_CONTROL 0x43
M98090_REG_ADC_CONTROL 0x44
M98090_REG_DRC_TIMING 0x33
M98090_REG_DRC_COMPRESSOR 0x34
M98090_REG_DRC_EXPANDER 0x35
M98090_REG_DSP_FILTER_ENABLE 0x41
M98090_REG_EQUALIZER_BASE 0x46
M98090_REG_RECORD_BIQUAD_BASE 0xAF
M98090_REG_DIGITAL_MIC_ENABLE 0x13
M98090_REG_DIGITAL_MIC_CONFIG 0x14
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20191128151908.180871-1-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
HP output driver has two parameters that can be configured to reduce
pop noise: power-on delay and ramp-up step time. Two new kcontrols
have been added to set these parameters.
Also have to alter timeout in aic31xx_dapm_power_event() because default
timeout does fire when higher supported power-on delay are configured.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20191128135447.26458-1-nikita.yoush@cogentembedded.com
Signed-off-by: Mark Brown <broonie@kernel.org>
max98090_interrupt() and max98090_pll_work() run in 2 different threads.
There are 2 possible races:
Note: M98090_REG_DEVICE_STATUS = 0x01.
Note: ULK == 0, PLL is locked; ULK == 1, PLL is unlocked.
max98090_interrupt max98090_pll_work
----------------------------------------------
schedule max98090_pll_work
restart max98090 codec
receive ULK INT
assert ULK == 0
schedule max98090_pll_work (1).
In the case (1), the PLL is locked but max98090_interrupt unnecessarily
schedules another max98090_pll_work.
max98090_interrupt max98090_pll_work max98090 codec
----------------------------------------------------------------------
ULK = 1
receive ULK INT
read 0x01
ULK = 0 (clear on read)
schedule max98090_pll_work
restart max98090 codec
ULK = 1
receive ULK INT
read 0x01
ULK = 0 (clear on read)
read 0x01
assert ULK == 0 (2).
In the case (2), both max98090_interrupt and max98090_pll_work read
the same clear-on-read register. max98090_pll_work would falsely
thought PLL is locked.
Note: the case (2) race is introduced by the previous commit ("ASoC:
max98090: exit workaround earlier if PLL is locked") to check the status
and exit the loop earlier in max98090_pll_work.
There are 2 possible solution options:
A. turn off ULK interrupt before scheduling max98090_pll_work; and turn
on again before exiting max98090_pll_work.
B. remove the second thread of execution.
Option A cannot fix the case (2) race because it still has 2 threads
access the same clear-on-read register simultaneously. Although we
could suppose the register is volatile and read the status via I2C could
be much slower than the hardware raises the bits.
Option B introduces a maximum 10~12 msec penalty delay in the interrupt
handler. However, it could only punish the jack detection by extra
10~12 msec.
Adopts option B which is the better solution overall.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20191122073114.219945-4-tzungbi@google.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It was observed Baytrail-based chromebooks could cause continuous PLL
unlocked when using playback stream and capture stream simultaneously.
Specifically, starting a capture stream after started a playback stream.
As a result, the audio data could corrupt or turn completely silent.
As the datasheet suggested, the maximum PLL lock time should be 7 msec.
The workaround resets the codec softly by toggling SHDN off and on if
PLL failed to lock for 10 msec. Notably, there is no suggested hold
time for SHDN off.
On Baytrail-based chromebooks, it would easily happen continuous PLL
unlocked if there is a 10 msec delay between SHDN off and on. Removes
the msleep().
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20191122073114.219945-2-tzungbi@google.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The simple-card tries to signal the codec to disable rate constraints,
see commit 2458adb8f9 ("SoC: simple-card-utils: set 0Hz to sysclk when
shutdown"). This wasn't handled by the codec, instead it would set the
FLL frequency to 0Hz which isn't working. Since we don't have any rate
constraints just ignore this request.
Fixes: 13409d27cb ("ASoC: wm8904: configure sysclk/FLL automatically")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191122232532.22258-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
If CONFIG_SPI is n, SND_SOC_RT5677_SPI also is n, building fails:
sound/soc/codecs/rt5677.o: In function `rt5677_irq':
rt5677.c:(.text+0x2dbf): undefined reference to `rt5677_spi_hotword_detected'
sound/soc/codecs/rt5677.o: In function `rt5677_dsp_work':
rt5677.c:(.text+0x3709): undefined reference to `rt5677_spi_write'
This adds stub helpers to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 461c623270 ("ASoC: rt5677: Load firmware via SPI using delayed work")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20191127082145.6100-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: More updates for v5.5
Some more development work for v5.5. Highlights include:
- More cleanups from Morimoto-san.
- Trigger word detection for RT5677.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The tlv320aic31xx devices allow to adjust the output common-mode voltage
for best analog performance. The datasheet states that the common mode
voltage should be set to be <= AVDD/2.
This changes allows to configure the output common-mode voltage via a DT
property. If the property is absent the voltage is automatically chosen
as the highest voltage below/equal to AVDD/2.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191118151207.28576-1-l.stach@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
In case the RST line is connected to a GPIO line it needs to be pulled high
when the driver probes to be able to use the codec.
Add support also for cases when more than one codec is is controlled by the
same GPIO line by requesting the gpio with GPIOD_FLAGS_BIT_NONEXCLUSIVE.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113124734.27984-3-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The current code assumes that the power is turned off in
SND_SOC_BIAS_OFF. If there are no actual regulator the codec isn't
turned off and the registers are not reset to their default values but
the regcache is still marked as dirty. Thus a value might not be written
to the hardware if it is set to the default value. Do a software reset
before turning off the power to make sure the registers are always reset
to their default states.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191112223629.21867-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
The headphone jack on buddy was broken with the following commit:
commit 6b5da66322 ("ASoC: rt5645: read jd1_1 status for jd
detection").
This changes the jd_mode for buddy to 4 so buddy can read from the same
register that was used in the working version of this driver without
affecting any other devices that might use this, since no other device uses
jd_mode = 4. To test this I plugged and uplugged the headphone jack, verifying
audio works.
Signed-off-by: Jacob Rasmussen <jacobraz@google.com>
Reviewed-by: Ross Zwisler <zwisler@google.com>
Link: https://lore.kernel.org/r/20191111185957.217244-1-jacobraz@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Due to limitations of the clocking configuration, we have no way of
scheduling our hibernation before the bdw dsp hibernates. This causes
issues when the system suspends with an open stream. We need userspace
to toggle the kcontrol before we are suspended so that any writes on
suspend are not lost and we don't corrupt the regmap.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-9-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The irq is disabled at suspend to avoid running the threaded irq
handler after the codec has been powered off. At resume, codec irq is
re-enabled and the interrupt status register is checked to see if
headphone has been pluggnd/unplugged while the device is suspended.
There is still a chance that the headphone gets enabled or disabled
after the codec is suspended. disable_irq syncs the threaded irq
handler, but soc-jack's threaded irq handler schedules a delayed
work to poll gpios (for debounce). This is still OK. The codec won't
be powered back on again because all audio paths have been suspended,
and there are no force enabled supply widgets (MICBIAS1 is disabled).
The gpio status read after codec power off could be wrong, so the
gpio values are checked again after resume.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-8-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
MCLK1 gets disabled at suspend and re-enabled at resume. Before
MCLK1 is re-enabled, if the DSP is already on (either the DSP was
left on during suspend, or the DSP is turned on early at resume),
i2c register read returns garbage and corrupts the regmap cache.
This patch stops the DSP before suspend and restarts it after
resume with a dalay to ensure MCLK is on while loading firmware.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-7-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec dies when RT5677_PWR_ANLG2(MX-64h) is set to 0xACE1
while it's streaming audio over SPI. The DSP firmware turns
on PLL2 (MX-64 bit 8) when SPI streaming starts. However regmap
does not believe that register can change by itself. When
BST1 (bit 15) is turned on with regmap_update_bits(), it doesn't
read the register first before write, so PLL2 power bit is
cleared by accident.
Marking MX-64h as volatile in regmap solved the issue.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-6-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Before a hotword is detected, GPIO1 pin is configured as IRQ
output so that jack detect works. When a hotword is detected,
the DSP firmware configures the GPIO1 pin as GPIO1 and
drives a 1. rt5677_irq() is called after a rising edge on
the GPIO1 pin, due to either jack detect event or hotword
event, or both. All possible events are checked and handled
in rt5677_irq() where GPIO1 pin is configured back to IRQ
output if a hotword is detected.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-4-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The firmware rt5677_elf_vad is an ELF binary obtained from
request_firmware(). Sections of the ELF are loaded to
the DSP via SPI. A model (e.g. en_us.mmap) can optionally be
loaded to the DSP at RT5677_MODEL_ADDR to overwrite the
baked-in model in rt5677_elf_vad.
Then we switch to DSP mode, load firmware, and let DSP run.
When a hotword is detected, an interrupt is fired and
rt5677_irq() is called. When 'DSP VAD Switch' is turned off,
the codec is set back to normal mode.
The kcontrol 'DSP VAD Switch' is automatically enabled/disabled
when the hotwording PCM stream is opened/closed.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191106011335.223061-2-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The recent change (*) in the ALSA memalloc core allows us to drop the
special vmalloc-specific allocation and page handling. This patch
coverts to the common code.
(*) 1fe7f397cf: ALSA: memalloc: Add vmalloc buffer allocation
support
7e8edae39f: ALSA: pcm: Handle special page mapping in the
default mmap handler
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20191108094641.20086-8-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent change (*) in the ALSA memalloc core allows us to drop the
special vmalloc-specific allocation and page handling. This patch
coverts to the common code.
(*) 1fe7f397cf: ALSA: memalloc: Add vmalloc buffer allocation
support
7e8edae39f: ALSA: pcm: Handle special page mapping in the
default mmap handler
Since it requires the specific buffer type (SNDRV_DMA_TYPE_VMALLOC),
it's set in the pcm_new ops now.
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20191108094641.20086-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASoC: Updates for v5.5
Some big changes in the core but more about cleanps and refactorings
than new features, plus a collection of new drivers and lots of small
fixes and improvements to existing ones.
- Lots more cleanups from Morimoto-san. Now that everything is a
component this is mostly about refactorings to clarify and simplify
the core, a combination of things that are no longer required due to
refactorings and spotting similarities.
- Many fixes to the Sound Open Firmware code.
- Wake on voice support for Chromebooks.
- SPI support for RT5677.
- New drivers for Analog Devices ADAU7118, Intel Cannonlake systems
with RT1011 and RT5682, Texas Instruments TAS2562 and TAS2770.
ASoC: Fixes for v5.4
These are a collection of fixes since v5.4-rc4 that have accumilated,
they're all driver specific and there's nothing major in here so it's
probably not essential to actually send them but I'll leave that call to
you.
When ASoC card instance is removed containing a HDA codec,
hdac_hda_codec_remove() may run in parallel with codec resume.
This will cause problems if the HDA link is freed with
snd_hdac_ext_bus_link_put() while the codec is still in
middle of its resume process.
To fix this, change the order such that pm_runtime_disable()
is called before the link is freed. This will ensure any
pending runtime PM action is completed before proceeding
to free the link.
This issue can be easily hit with e.g. SOF driver by loading and
unloading the drivers.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101170635.26389-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
