imx7d (and imx8mm, imx8mn) uses Samsung PHY and USB generic PHY driver.
The USB generic PHY driver is impossible to have a charger detection
for every user, so we implement USB charger detection routine at glue
layer. After the detection has finished, it will notify USB PHY
charger framework, and the uevents will be triggered.
Signed-off-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Some vendors glue layer need to handle some events for vbus, eg,
some i.mx platforms (imx7d, imx8mm, imx8mn, etc) needs vbus event
to handle charger detection, its charger detection is finished at
glue layer code, but not at USB PHY driver.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev
0.6, when a device is transitioning to DP Alternate Mode state, if the
HPD_STATE (bit 7) field in the status update command VDO is set to
HPD_HIGH, the HPD_HIGH field in the Alternate Mode request “mode_data”
field (bit 14) should also be set. Ensure the bit is correctly handled
while issuing the Alternate Mode request.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Fixes: 6701adfa96 ("usb: typec: driver for Intel PMC mux control")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200429054432.134178-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some architectures (e.g. arm64) requests for
IO coherent memory may use non-cachable attributes if
the relevant device isn't cache coherent. If these
pages are then remapped into userspace as cacheable,
they may not be coherent with the non-cacheable mappings.
In particular this happens with libusb, when it attempts
to create zero-copy buffers for use by rtl-sdr
(https://github.com/osmocom/rtl-sdr/). On low end arm
devices with non-coherent USB ports, the application will
be unexpectedly killed, while continuing to work fine on
arm machines with coherent USB controllers.
This bug has been discovered/reported a few times over
the last few years. In the case of rtl-sdr a compile time
option to enable/disable zero copy was implemented to
work around it.
Rather than relaying on application specific workarounds,
dma_mmap_coherent() can be used instead of remap_pfn_range().
The page cache/etc attributes will then be correctly set in
userspace to match the kernel mapping.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200504201348.1183246-1-jeremy.linton@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot fuzzer found a race between URB submission to endpoint 0
and device reset. Namely, during the reset we call usb_ep0_reinit()
because the characteristics of ep0 may have changed (if the reset
follows a firmware update, for example). While usb_ep0_reinit() is
running there is a brief period during which the pointers stored in
udev->ep_in[0] and udev->ep_out[0] are set to NULL, and if an URB is
submitted to ep0 during that period, usb_urb_ep_type_check() will
report it as a driver bug. In the absence of those pointers, the
routine thinks that the endpoint doesn't exist. The log message looks
like this:
------------[ cut here ]------------
usb 2-1: BOGUS urb xfer, pipe 2 != type 2
WARNING: CPU: 0 PID: 9241 at drivers/usb/core/urb.c:478
usb_submit_urb+0x1188/0x1460 drivers/usb/core/urb.c:478
Now, although submitting an URB while the device is being reset is a
questionable thing to do, it shouldn't count as a driver bug as severe
as submitting an URB for an endpoint that doesn't exist. Indeed,
endpoint 0 always exists, even while the device is in its unconfigured
state.
To prevent these misleading driver bug reports, this patch updates
usb_disable_endpoint() to avoid clearing the ep_in[] and ep_out[]
pointers when the endpoint being disabled is ep0. There's no danger
of leaving a stale pointer in place, because the usb_host_endpoint
structure being pointed to is stored permanently in udev->ep0; it
doesn't get deallocated until the entire usb_device structure does.
Reported-and-tested-by: syzbot+db339689b2101f6f6071@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2005011558590.903-100000@netrider.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the driver issued START_TRANSFER and received a no-resource status,
then generally there are a few reasons for this:
1) The driver did not allocate resource for the endpoint during
power-on-reset initialization.
2) The transfer resource was reset. At this moment, we don't do this in
the driver, but it occurs when the driver issues START_CONFIG cmd to ep0
with resource index=2.
3) The driver issues the START_TRANSFER command to an already started
endpoint. Usually, this is because the END_TRANSFER command hasn't
completed yet.
Print out a warning to help debug this issue in the driver.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
After a number of unsuccessful start isoc attempts due to bus-expiry
status, issue END_TRANSFER command and retry on the next XferNotReady
event.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
As long as the START_TRANSFER command completes, it provides the
resource index of the endpoint. Use this when we need to issue
END_TRANSFER command to an isoc endpoint to retry with a new
XferNotReady event.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If dwc3 fails to issue START_TRANSFER/UPDATE_TRANSFER command, then we
should properly end an active transfer and give back all the started
requests. However if it's for an isoc endpoint, the failure maybe due to
bus-expiry status. In this case, don't give back the requests and wait
for the next retry.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the driver is configured to use DRD role-switch, let the drd code
path decide the default dr_mode.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the driver is configured to use DRD role-switch, it's not OTG. There
won't be OTG irq to free. Check for dwc->otg_irq before freeing it.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Refactor the USB2 PHY init code patch to handle the Amlogic GXL/GXM
not having the PHY mode control registers in the Glue but in the PHY
registers.
The Amlogic GXL/GXM will call phy_set_mode() instead of programming the
PHY mode control registers, thus add two new callbacks to the SoC match
data.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
On the Amlogic GXL/GXM SoCs, only the USB control registers are available,
the PHY mode being handled in the PHY registers.
Thus, handle the PHY mode registers in separate regmaps and prepare
support for Amlogic GXL/GXM SoCs by moving the regmap setup in a callback
set in the SoC match data.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The flow from function dwc3_gadget_ep_dequeue() is not easy to follow.
Refactor it for easier read. No functional change in this commit.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Remove 2 unnecessary checks:
1) A request in the started_list must have its trb field set. So
checking for req->trb is unnecessary.
2) An endpoint must have started (and have not ended) for the request to
still be in the started_list. There's no point to check if the endpoint
is started. We had this check because previously the driver didn't
handle the endpoint's started/ended flags for END_TRANSFER command
properly. See commit 9f45581f5e ("usb: dwc3: gadget: early giveback
if End Transfer already completed").
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If a request is dequeued, the transfer is cancelled. Give back all
the started requests.
In most scenarios, the function driver dequeues all requests of a
transfer when there's a failure. If the function driver follows this,
then it's fine. If not, then we'd be skipping TRBs at different points
within the dequeue and enqueue pointers, making dequeue/enqueue pointers
useless. To enforce and make sure that we're properly skipping TRBs,
cancel all the started requests and give back all the cancelled requests
to the function drivers.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
DWC3 must not issue CLEAR_STALL command to control endpoints. The
controller automatically clears the STALL when it receives the SETUP
token. Also, when the driver receives ClearFeature(halt_ep), DWC3 must
stop any active transfer from the endpoint and give back all the
requests to the function drivers.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch moves patch-usb1-dev-desc logic from get-descriptor handler
to "ast_vhub_fixup_usb1_dev_desc" function so the code is executed only
once (at vhub initial time).
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The patch overrides idVendor, idProduct and bcdDevice fields in vhub
Device Descriptor if according device tree properties are defined.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If "vhub,string-descriptor" device tree property is defined, the driver
will load string descriptors from device tree; otherwise, the default
string descriptors will be used.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The USB LANGID validation code in "check_user_usb_string" function is
moved to "usb_validate_langid" function which can be used by other usb
gadget drivers.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch introduces a link list to store string descriptors with
different languages, and "ast_vhub_rep_string" function is also improved
to support multiple language usb strings.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch evaluates vhub ports' irq mask before going through per-port
irq handling one by one, which helps to speed up irq handling in case
there is no port interrupt.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The DRD module calls dwc3_set_mode() on role switches, i.e. when a device is
being plugged in. In order to support continuous runtime power management when
plugging in / unplugging a cable, we need to call pm_runtime_get_sync() in
this path.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Mark all local functions static to fix sparse warnings.
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the SPDX License Identifier style in
header files related to DesignWare USB2 DRD Core Support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the SPDX License Identifier style in
header files related to DesignWare USB3 DRD Core Support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the SPDX License Identifier style in
header files related to USB peripheral controller drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following coccicheck warning:
drivers/usb/chipidea/ci_hdrc_usb2.c:75:28-29: Unneeded semicolon
Fixes: c2de37b31f ("usb: chipidea: usb2: make clock optional")
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
This driver only creates a bunch of platform devices sharing resources
belonging to the PMC device. This is pretty much what MFD subsystem is
for so move the driver there, renaming it to intel_pmc_bxt.c which
should be more clear what it is.
MFD subsystem provides nice helper APIs for subdevice creation so
convert the driver to use those. Unfortunately the ACPI device includes
separate resources for most of the subdevices so we cannot simply call
mfd_add_devices() to create all of them but instead we need to call it
separately for each device.
The new MFD driver continues to expose two sysfs attributes that allow
userspace to send IPC commands to the PMC/SCU to avoid breaking any
existing applications that may use these. Generally this is bad idea so
document this in the ABI documentation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert the driver to use the new SCU IPC API. This allows us to get rid
of the duplicate PMC IPC implementation which is now covered in SCU IPC
driver.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
With this change the UCSI device will show up in
/sys/class/power_supply/. The following values are exported:
- online
- usb_type
- voltage_min
- voltage_max
- voltage_now
- current_max
- current_now
Once a PD-capable type-C power source is connected to the system, GET_PDOS
UCSI command is used to query all source capabilities. Request data object
(RDO) is used to get current values.
Signed-off-by: K V, Abhilash <abhilash.k.v@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200423132058.6972-7-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EC firmware on Dell XPS & Latitude series does not set "Power Operation
Mode Change" bit in "Connector Status change" field of MESSAGE IN Data
while transitioning from type-C current to PD mode.
Instead the "Negotiated Power Level Change" bit is set when the "Power
Operation Mode" field shows the correct mode (i.e. PD).
This patch adds a check for this bit also, to trigger an update of
power operation mode in class driver, while handling GET_CONNECTOR_STATUS
command.
Signed-off-by: K V, Abhilash <abhilash.k.v@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200423132058.6972-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently UCSI framework doesn't update USB data role when partner type
is reported as power cable or power cable with ufp connected. This
results into no USB host mode functionality. This is valid usecase where
user wants to use legacy type c power cable with type a female connector
to attach different USB devices like mouse, thumb drive etc. Hence update
USB data role as host when partner type is reported as power cable or
power cable with ufp connected.
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200423132058.6972-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
