The current driver responds to TEST UNIT READY (TUR) with a GOOD status
immediately after a scsi_debug device (LU) is created. This is unrealistic
as even SSDs take some time after power-on before accepting media access
commands.
Add the tur_ms_to_ready parameter whose unit is milliseconds (default 0)
and is the period before which a TUR (or any media access command) will set
the CHECK CONDITION status with a sense key of NOT READY and an additional
sense of "Logical unit is in process of becoming ready". The period starts
when each scsi_debug device is created.
This patch was prompted by T10 proposal 20-061r2 which was accepted on
2020716. It adds that a TUR in the situation described in the previous
paragraph may set the INFO field (or descriptor) in the sense data to the
estimated number in milliseconds before a subsequent TUR will yield a GOOD
status. This patch follows that advice.
Link: https://lore.kernel.org/r/20200724155531.668144-1-dgilbert@interlog.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SCSI REQUEST SENSE command emulation was found to be broken. It is a
quite complex command so try and make it do a subset of what it should
do. Remove the attempt to mimic SCSI-1 REQUEST SENSE (i.e. return the sense
data for the previous failed command). Add some reporting of "pollable"
sense data [see spc6r02: 5.12.2]. Keep the IEC mode page MRIE=6 TEST=1
predictive failure reporting.
Link: https://lore.kernel.org/r/20200723194819.545573-1-dgilbert@interlog.com
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
Only declare 'core_nr' if its conditions for use are met.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/mvsas/mv_init.c: In function ‘mvs_interrupt’:
drivers/scsi/mvsas/mv_init.c:180:6: warning: variable ‘core_nr’ set but not used [-Wunused-but-set-variable]
drivers/scsi/mvsas/mv_init.c: In function ‘mvs_ioremap’:
drivers/scsi/mvsas/mv_init.c:302:36: warning: variable ‘res_flag’ set but not used [-Wunused-but-set-variable]
[mkp: applied follow-up fixup patch]
Link: https://lore.kernel.org/r/20200721164148.2617584-40-lee.jones@linaro.org
Cc: Jason Yan <yanaijie@huawei.com>
Cc: Marvell <kewei@marvell.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/esas2r/esas2r_log.c:86: warning: Function parameter or member 'level' not described in 'translate_esas2r_event_level_to_kernel'
drivers/scsi/esas2r/esas2r_log.c:120: warning: Function parameter or member 'level' not described in 'esas2r_log_master'
drivers/scsi/esas2r/esas2r_log.c:120: warning: Function parameter or member 'dev' not described in 'esas2r_log_master'
drivers/scsi/esas2r/esas2r_log.c:120: warning: Function parameter or member 'format' not described in 'esas2r_log_master'
drivers/scsi/esas2r/esas2r_log.c:120: warning: Function parameter or member 'args' not described in 'esas2r_log_master'
drivers/scsi/esas2r/esas2r_log.c:183: warning: Function parameter or member 'level' not described in 'esas2r_log'
drivers/scsi/esas2r/esas2r_log.c:183: warning: Function parameter or member 'format' not described in 'esas2r_log'
drivers/scsi/esas2r/esas2r_log.c:211: warning: Function parameter or member 'level' not described in 'esas2r_log_dev'
drivers/scsi/esas2r/esas2r_log.c:211: warning: Function parameter or member 'dev' not described in 'esas2r_log_dev'
drivers/scsi/esas2r/esas2r_log.c:211: warning: Function parameter or member 'format' not described in 'esas2r_log_dev'
drivers/scsi/esas2r/esas2r_log.c:237: warning: Function parameter or member 'level' not described in 'esas2r_log_hexdump'
drivers/scsi/esas2r/esas2r_log.c:237: warning: Function parameter or member 'buf' not described in 'esas2r_log_hexdump'
drivers/scsi/esas2r/esas2r_log.c:237: warning: Function parameter or member 'len' not described in 'esas2r_log_hexdump'
Link: https://lore.kernel.org/r/20200723122446.1329773-41-lee.jones@linaro.org
Cc: Bradley Grove <linuxdrivers@attotech.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is probably historical (Doxygen?).
Fixes the following W=1 kernel build warning(s):
drivers/scsi/bfa/bfa_ioc.c:6646: warning: Cannot understand * @brief hardware error definition
drivers/scsi/bfa/bfa_ioc.c:6661: warning: Cannot understand * @brief flash command register data structure
drivers/scsi/bfa/bfa_ioc.c:6685: warning: Cannot understand * @brief flash device status register data structure
drivers/scsi/bfa/bfa_ioc.c:6711: warning: Cannot understand * @brief flash address register data structure
drivers/scsi/bfa/bfa_ioc.c:6732: warning: Function parameter or member 'pci_bar' not described in 'bfa_flash_set_cmd'
drivers/scsi/bfa/bfa_ioc.c:6732: warning: Function parameter or member 'wr_cnt' not described in 'bfa_flash_set_cmd'
drivers/scsi/bfa/bfa_ioc.c:6732: warning: Function parameter or member 'rd_cnt' not described in 'bfa_flash_set_cmd'
drivers/scsi/bfa/bfa_ioc.c:6732: warning: Function parameter or member 'ad_cnt' not described in 'bfa_flash_set_cmd'
drivers/scsi/bfa/bfa_ioc.c:6732: warning: Function parameter or member 'op' not described in 'bfa_flash_set_cmd'
drivers/scsi/bfa/bfa_ioc.c:6768: warning: Cannot understand * @brief
drivers/scsi/bfa/bfa_ioc.c:6807: warning: Cannot understand * @brief
drivers/scsi/bfa/bfa_ioc.c:6852: warning: Cannot understand * @brief
drivers/scsi/bfa/bfa_ioc.c:6898: warning: Cannot understand * @brief
drivers/scsi/bfa/bfa_ioc.c:6914: warning: Cannot understand * @brief
drivers/scsi/bfa/bfa_ioc.c:6940: warning: Cannot understand * @brief
Link: https://lore.kernel.org/r/20200723122446.1329773-34-lee.jones@linaro.org
Cc: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Cc: Sudarsana Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In certain configurations esas2r_bugon() is sometimes NULLed by the compiler.
Fixes the following W=1 kernel build warning(s):
In file included from drivers/scsi/esas2r/esas2r_log.c:44:
drivers/scsi/esas2r/esas2r.h: In function ‘esas2r_rq_init_request’:
drivers/scsi/esas2r/esas2r.h:1229:17: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
1229 | esas2r_bugon();
| ^
NB: Lots of these - snipped for brevity
Link: https://lore.kernel.org/r/20200723122446.1329773-33-lee.jones@linaro.org
Cc: Bradley Grove <linuxdrivers@attotech.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/bnx2i/bnx2i_iscsi.c:241: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_bind_conn_to_iscsi_cid'
drivers/scsi/bnx2i/bnx2i_iscsi.c:241: warning: Excess function parameter 'conn' description in 'bnx2i_bind_conn_to_iscsi_cid'
drivers/scsi/bnx2i/bnx2i_iscsi.c:470: warning: Excess function parameter 'cmd' description in 'bnx2i_destroy_cmd_pool'
drivers/scsi/bnx2i/bnx2i_iscsi.c:595: warning: Function parameter or member 'cls_session' not described in 'bnx2i_drop_session'
drivers/scsi/bnx2i/bnx2i_iscsi.c:595: warning: Excess function parameter 'hba' description in 'bnx2i_drop_session'
drivers/scsi/bnx2i/bnx2i_iscsi.c:595: warning: Excess function parameter 'session' description in 'bnx2i_drop_session'
drivers/scsi/bnx2i/bnx2i_iscsi.c:1290: warning: Function parameter or member 'ep' not described in 'bnx2i_session_create'
drivers/scsi/bnx2i/bnx2i_iscsi.c:1979: warning: Function parameter or member 'bnx2i_ep' not described in 'bnx2i_ep_tcp_conn_active'
drivers/scsi/bnx2i/bnx2i_iscsi.c:1979: warning: Excess function parameter 'ep' description in 'bnx2i_ep_tcp_conn_active'
drivers/scsi/bnx2i/bnx2i_iscsi.c:2178: warning: Function parameter or member 'shost' not described in 'bnx2i_nl_set_path'
drivers/scsi/bnx2i/bnx2i_iscsi.c:2178: warning: Function parameter or member 'params' not described in 'bnx2i_nl_set_path'
drivers/scsi/bnx2i/bnx2i_iscsi.c:2178: warning: Excess function parameter 'buf' description in 'bnx2i_nl_set_path'
Link: https://lore.kernel.org/r/20200723122446.1329773-30-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Cc: Anil Veerabhadrappa <anilgv@broadcom.com>
Cc: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mainly renames and docrot issues.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/bnx2i/bnx2i_hwi.c:194: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_get_rq_buf'
drivers/scsi/bnx2i/bnx2i_hwi.c:194: warning: Excess function parameter 'conn' description in 'bnx2i_get_rq_buf'
drivers/scsi/bnx2i/bnx2i_hwi.c:232: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_put_rq_buf'
drivers/scsi/bnx2i/bnx2i_hwi.c:232: warning: Excess function parameter 'conn' description in 'bnx2i_put_rq_buf'
drivers/scsi/bnx2i/bnx2i_hwi.c:269: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_ring_sq_dbell'
drivers/scsi/bnx2i/bnx2i_hwi.c:269: warning: Excess function parameter 'conn' description in 'bnx2i_ring_sq_dbell'
drivers/scsi/bnx2i/bnx2i_hwi.c:293: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_ring_dbell_update_sq_params'
drivers/scsi/bnx2i/bnx2i_hwi.c:293: warning: Excess function parameter 'conn' description in 'bnx2i_ring_dbell_update_sq_params'
drivers/scsi/bnx2i/bnx2i_hwi.c:331: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_send_iscsi_login'
drivers/scsi/bnx2i/bnx2i_hwi.c:331: warning: Function parameter or member 'task' not described in 'bnx2i_send_iscsi_login'
drivers/scsi/bnx2i/bnx2i_hwi.c:331: warning: Excess function parameter 'conn' description in 'bnx2i_send_iscsi_login'
drivers/scsi/bnx2i/bnx2i_hwi.c:331: warning: Excess function parameter 'cmd' description in 'bnx2i_send_iscsi_login'
drivers/scsi/bnx2i/bnx2i_hwi.c:384: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_send_iscsi_tmf'
drivers/scsi/bnx2i/bnx2i_hwi.c:384: warning: Excess function parameter 'conn' description in 'bnx2i_send_iscsi_tmf'
drivers/scsi/bnx2i/bnx2i_hwi.c:458: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_send_iscsi_text'
drivers/scsi/bnx2i/bnx2i_hwi.c:458: warning: Excess function parameter 'conn' description in 'bnx2i_send_iscsi_text'
drivers/scsi/bnx2i/bnx2i_hwi.c:506: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_send_iscsi_scsicmd'
drivers/scsi/bnx2i/bnx2i_hwi.c:506: warning: Excess function parameter 'conn' description in 'bnx2i_send_iscsi_scsicmd'
drivers/scsi/bnx2i/bnx2i_hwi.c:533: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_send_iscsi_nopout'
drivers/scsi/bnx2i/bnx2i_hwi.c:533: warning: Function parameter or member 'task' not described in 'bnx2i_send_iscsi_nopout'
drivers/scsi/bnx2i/bnx2i_hwi.c:533: warning: Excess function parameter 'conn' description in 'bnx2i_send_iscsi_nopout'
drivers/scsi/bnx2i/bnx2i_hwi.c:533: warning: Excess function parameter 'cmd' description in 'bnx2i_send_iscsi_nopout'
drivers/scsi/bnx2i/bnx2i_hwi.c:590: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_send_iscsi_logout'
drivers/scsi/bnx2i/bnx2i_hwi.c:590: warning: Function parameter or member 'task' not described in 'bnx2i_send_iscsi_logout'
drivers/scsi/bnx2i/bnx2i_hwi.c:590: warning: Excess function parameter 'conn' description in 'bnx2i_send_iscsi_logout'
drivers/scsi/bnx2i/bnx2i_hwi.c:590: warning: Excess function parameter 'cmd' description in 'bnx2i_send_iscsi_logout'
drivers/scsi/bnx2i/bnx2i_hwi.c:686: warning: Function parameter or member 't' not described in 'bnx2i_ep_ofld_timer'
drivers/scsi/bnx2i/bnx2i_hwi.c:686: warning: Excess function parameter 'data' description in 'bnx2i_ep_ofld_timer'
drivers/scsi/bnx2i/bnx2i_hwi.c:1672: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_unsol_pdu_adjust_rq'
drivers/scsi/bnx2i/bnx2i_hwi.c:1672: warning: Excess function parameter 'conn' description in 'bnx2i_unsol_pdu_adjust_rq'
drivers/scsi/bnx2i/bnx2i_hwi.c:1900: warning: Function parameter or member 'session' not described in 'bnx2i_queue_scsi_cmd_resp'
drivers/scsi/bnx2i/bnx2i_hwi.c:1900: warning: Function parameter or member 'cqe' not described in 'bnx2i_queue_scsi_cmd_resp'
drivers/scsi/bnx2i/bnx2i_hwi.c:2476: warning: Function parameter or member 'context' not described in 'bnx2i_indicate_kcqe'
drivers/scsi/bnx2i/bnx2i_hwi.c:2476: warning: Function parameter or member 'kcqe' not described in 'bnx2i_indicate_kcqe'
drivers/scsi/bnx2i/bnx2i_hwi.c:2476: warning: Function parameter or member 'num_cqe' not described in 'bnx2i_indicate_kcqe'
drivers/scsi/bnx2i/bnx2i_hwi.c:2476: warning: Excess function parameter 'hba' description in 'bnx2i_indicate_kcqe'
drivers/scsi/bnx2i/bnx2i_hwi.c:2476: warning: Excess function parameter 'update_kcqe' description in 'bnx2i_indicate_kcqe'
drivers/scsi/bnx2i/bnx2i_hwi.c:2624: warning: Function parameter or member 'cm_sk' not described in 'bnx2i_cm_remote_close'
drivers/scsi/bnx2i/bnx2i_hwi.c:2624: warning: Excess function parameter 'hba' description in 'bnx2i_cm_remote_close'
drivers/scsi/bnx2i/bnx2i_hwi.c:2624: warning: Excess function parameter 'update_kcqe' description in 'bnx2i_cm_remote_close'
drivers/scsi/bnx2i/bnx2i_hwi.c:2641: warning: Function parameter or member 'cm_sk' not described in 'bnx2i_cm_remote_abort'
drivers/scsi/bnx2i/bnx2i_hwi.c:2641: warning: Excess function parameter 'hba' description in 'bnx2i_cm_remote_abort'
drivers/scsi/bnx2i/bnx2i_hwi.c:2641: warning: Excess function parameter 'update_kcqe' description in 'bnx2i_cm_remote_abort'
drivers/scsi/bnx2i/bnx2i_hwi.c:2677: warning: cannot understand function prototype: 'struct cnic_ulp_ops bnx2i_cnic_cb = '
Link: https://lore.kernel.org/r/20200723122446.1329773-29-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Cc: Anil Veerabhadrappa <anilgv@broadcom.com>
Cc: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/bfa/bfa_ioc_ct.c:504: warning: Function parameter or member 'ioc' not described in 'bfa_ioc_set_ctx_hwif'
drivers/scsi/bfa/bfa_ioc_ct.c:504: warning: Function parameter or member 'hwif' not described in 'bfa_ioc_set_ctx_hwif'
drivers/scsi/bfa/bfa_ioc_ct.c:525: warning: Function parameter or member 'ioc' not described in 'bfa_ioc_set_ct_hwif'
drivers/scsi/bfa/bfa_ioc_ct.c:540: warning: Function parameter or member 'ioc' not described in 'bfa_ioc_set_ct2_hwif'
Link: https://lore.kernel.org/r/20200723122446.1329773-26-lee.jones@linaro.org
Cc: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Cc: Sudarsana Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/csiostor/csio_hw_t5.c: In function ‘csio_t5_mc_read’:
drivers/scsi/csiostor/csio_hw_t5.c:151:11: warning: variable ‘mc_bist_status_rdata_reg’ set but not used [-Wunused-but-set-variable]
151 | uint32_t mc_bist_status_rdata_reg, mc_bist_data_pattern_reg;
| ^~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/csiostor/csio_hw_t5.c: In function ‘csio_t5_edc_read’:
drivers/scsi/csiostor/csio_hw_t5.c:199:38: warning: variable ‘edc_bist_status_rdata_reg’ set but not used [-Wunused-but-set-variable]
199 | uint32_t edc_bist_cmd_data_pattern, edc_bist_status_rdata_reg;
| ^~~~~~~~~~~~~~~~~~~~~~~~~
Link: https://lore.kernel.org/r/20200723122446.1329773-23-lee.jones@linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/bfa/bfa_ioc.c: In function ‘bfa_iocpf_sm_fwcheck_entry’:
drivers/scsi/bfa/bfa_ioc.c:704:27: warning: variable ‘pgoff’ set but not used [-Wunused-but-set-variable]
drivers/scsi/bfa/bfa_ioc.c: In function ‘bfa_ioc_fwver_get’:
drivers/scsi/bfa/bfa_ioc.c:1443:13: warning: variable ‘pgoff’ set but not used [-Wunused-but-set-variable]
drivers/scsi/bfa/bfa_ioc.c: In function ‘bfa_ioc_fwsig_invalidate’:
drivers/scsi/bfa/bfa_ioc.c:1665:13: warning: variable ‘pgoff’ set but not used [-Wunused-but-set-variable]
drivers/scsi/bfa/bfa_ioc.c: In function ‘bfa_ioc_download_fw’:
drivers/scsi/bfa/bfa_ioc.c:1866:13: warning: variable ‘pgoff’ set but not used [-Wunused-but-set-variable]
drivers/scsi/bfa/bfa_ioc.c: In function ‘bfa_diag_memtest_done’:
drivers/scsi/bfa/bfa_ioc.c:4766:13: warning: variable ‘pgoff’ set but not used [-Wunused-but-set-variable]
drivers/scsi/bfa/bfa_ioc.c: In function ‘bfa_flash_fifo_flush’:
drivers/scsi/bfa/bfa_ioc.c:6787:6: warning: variable ‘t’ set but not used [-Wunused-but-set-variable]
Link: https://lore.kernel.org/r/20200723122446.1329773-21-lee.jones@linaro.org
Cc: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Cc: Sudarsana Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adding, removing and correcting function parameter descriptions.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_mbox.c:886: warning: Function parameter or member 'vport' not described in 'lpfc_reg_vpi'
drivers/scsi/lpfc/lpfc_mbox.c:886: warning: Excess function parameter 'phba' description in 'lpfc_reg_vpi'
drivers/scsi/lpfc/lpfc_mbox.c:886: warning: Excess function parameter 'vpi' description in 'lpfc_reg_vpi'
drivers/scsi/lpfc/lpfc_mbox.c:886: warning: Excess function parameter 'sid' description in 'lpfc_reg_vpi'
drivers/scsi/lpfc/lpfc_mbox.c:1218: warning: Function parameter or member 'ring' not described in 'lpfc_config_ring'
drivers/scsi/lpfc/lpfc_mbox.c:1626: warning: Function parameter or member 'mboxq' not described in 'lpfc_mbox_tmo_val'
drivers/scsi/lpfc/lpfc_mbox.c:1626: warning: Excess function parameter 'cmd' description in 'lpfc_mbox_tmo_val'
drivers/scsi/lpfc/lpfc_mbox.c:1710: warning: Function parameter or member 'sge' not described in 'lpfc_sli4_mbx_sge_get'
drivers/scsi/lpfc/lpfc_mbox.c:1780: warning: Function parameter or member 'emb' not described in 'lpfc_sli4_config'
drivers/scsi/lpfc/lpfc_mbox.c:2027: warning: Function parameter or member 'mboxq' not described in 'lpfc_sli4_mbx_read_fcf_rec'
drivers/scsi/lpfc/lpfc_mbox.c:2078: warning: Function parameter or member 'phba' not described in 'lpfc_request_features'
Link: https://lore.kernel.org/r/20200723122446.1329773-19-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/qla4xxx/ql4_bsg.c:811: warning: Function parameter or member 'bsg_job' not described in 'qla4xxx_process_vendor_specific'
drivers/scsi/qla4xxx/ql4_bsg.c:811: warning: Excess function parameter 'job' description in 'qla4xxx_process_vendor_specific'
drivers/scsi/qla4xxx/ql4_bsg.c:858: warning: Function parameter or member 'bsg_job' not described in 'qla4xxx_bsg_request'
drivers/scsi/qla4xxx/ql4_bsg.c:858: warning: Excess function parameter 'job' description in 'qla4xxx_bsg_request'
Link: https://lore.kernel.org/r/20200723122446.1329773-18-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_init.c:1136: warning: Function parameter or member 't' not described in 'lpfc_hb_timeout'
drivers/scsi/lpfc/lpfc_init.c:1136: warning: Excess function parameter 'ptr' description in 'lpfc_hb_timeout'
drivers/scsi/lpfc/lpfc_init.c:1170: warning: Function parameter or member 't' not described in 'lpfc_rrq_timeout'
drivers/scsi/lpfc/lpfc_init.c:1170: warning: Excess function parameter 'ptr' description in 'lpfc_rrq_timeout'
drivers/scsi/lpfc/lpfc_init.c:1232: warning: Function parameter or member 'work' not described in 'lpfc_idle_stat_delay_work'
drivers/scsi/lpfc/lpfc_init.c:1817: warning: Function parameter or member 'en_rn_msg' not described in 'lpfc_sli4_port_sta_fn_reset'
drivers/scsi/lpfc/lpfc_init.c:3033: warning: Function parameter or member 'mbx_action' not described in 'lpfc_block_mgmt_io'
drivers/scsi/lpfc/lpfc_init.c:3481: warning: Function parameter or member 'mbx_action' not described in 'lpfc_offline_prep'
drivers/scsi/lpfc/lpfc_init.c:4150: warning: Function parameter or member 'phba' not described in 'lpfc_new_io_buf'
drivers/scsi/lpfc/lpfc_init.c:4150: warning: Function parameter or member 'num_to_alloc' not described in 'lpfc_new_io_buf'
drivers/scsi/lpfc/lpfc_init.c:4150: warning: Excess function parameter 'vport' description in 'lpfc_new_io_buf'
drivers/scsi/lpfc/lpfc_init.c:4150: warning: Excess function parameter 'num_to_allocate' description in 'lpfc_new_io_buf'
drivers/scsi/lpfc/lpfc_init.c:4736: warning: Function parameter or member 't' not described in 'lpfc_sli4_fcf_redisc_wait_tmo'
drivers/scsi/lpfc/lpfc_init.c:4736: warning: Excess function parameter 'ptr' description in 'lpfc_sli4_fcf_redisc_wait_tmo'
drivers/scsi/lpfc/lpfc_init.c:5103: warning: Excess function parameter 'evt_code' description in 'lpfc_async_link_speed_to_read_top'
drivers/scsi/lpfc/lpfc_init.c:5377: warning: Function parameter or member 'acqe_sli' not described in 'lpfc_sli4_async_sli_evt'
drivers/scsi/lpfc/lpfc_init.c:5377: warning: Excess function parameter 'acqe_fc' description in 'lpfc_sli4_async_sli_evt'
drivers/scsi/lpfc/lpfc_init.c:5634: warning: Function parameter or member 'phba' not described in 'lpfc_sli4_perform_all_vport_cvl'
drivers/scsi/lpfc/lpfc_init.c:5634: warning: Excess function parameter 'vport' description in 'lpfc_sli4_perform_all_vport_cvl'
drivers/scsi/lpfc/lpfc_init.c:5655: warning: Function parameter or member 'acqe_fip' not described in 'lpfc_sli4_async_fip_evt'
drivers/scsi/lpfc/lpfc_init.c:5655: warning: Excess function parameter 'acqe_link' description in 'lpfc_sli4_async_fip_evt'
drivers/scsi/lpfc/lpfc_init.c:5908: warning: Function parameter or member 'acqe_dcbx' not described in 'lpfc_sli4_async_dcbx_evt'
drivers/scsi/lpfc/lpfc_init.c:5908: warning: Excess function parameter 'acqe_link' description in 'lpfc_sli4_async_dcbx_evt'
drivers/scsi/lpfc/lpfc_init.c:5927: warning: Function parameter or member 'acqe_grp5' not described in 'lpfc_sli4_async_grp5_evt'
drivers/scsi/lpfc/lpfc_init.c:5927: warning: Excess function parameter 'acqe_link' description in 'lpfc_sli4_async_grp5_evt'
drivers/scsi/lpfc/lpfc_init.c:7279: warning: Function parameter or member 'iocb_count' not described in 'lpfc_init_iocb_list'
drivers/scsi/lpfc/lpfc_init.c:8227: warning: Function parameter or member 'if_type' not described in 'lpfc_sli4_bar1_register_memmap'
drivers/scsi/lpfc/lpfc_init.c:8414: warning: Excess function parameter 'phba' description in 'LINK_FLAGS_DEF'
drivers/scsi/lpfc/lpfc_init.c:8414: warning: Excess function parameter 'rdconf' description in 'LINK_FLAGS_DEF'
drivers/scsi/lpfc/lpfc_init.c:10734: warning: Function parameter or member 'cfg_mode' not described in 'lpfc_sli_enable_intr'
drivers/scsi/lpfc/lpfc_init.c:11241: warning: Function parameter or member 'eqlist' not described in 'lpfc_cpuhp_get_eq'
drivers/scsi/lpfc/lpfc_init.c:11726: warning: Function parameter or member 'cfg_mode' not described in 'lpfc_sli4_enable_intr'
drivers/scsi/lpfc/lpfc_init.c:12997: warning: Excess function parameter 'ret' description in 'lpfc_write_firmware'
drivers/scsi/lpfc/lpfc_init.c:13103: warning: Function parameter or member 'fw_upgrade' not described in 'lpfc_sli4_request_firmware_update'
Link: https://lore.kernel.org/r/20200723122446.1329773-17-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
In file included from arch/arm/include/asm/io.h:23,
from drivers/scsi/ips.c:164:
In function ‘strncpy’,
inlined from ‘ips_send_cmd’ at drivers/scsi/ips.c:3522:6:
include/linux/string.h:297:30: warning: ‘__builtin_strncpy’ output
truncated before terminating nul cop ying 4 bytes from a string of the same length [-Wstringop-truncation]
297 | #define __underlying_strncpy __builtin_strncpy
| ^
include/linux/string.h:307:9: note: in expansion of macro ‘__underlying_strncpy’
307 | return __underlying_strncpy(p, q, size);
| ^~~~~~~~~~~~~~~~~~~~
NB: Lots of these - snipping for brevity
Link: https://lore.kernel.org/r/20200723122446.1329773-14-lee.jones@linaro.org
Cc: Adaptec OEM Raid Solutions <aacraid@microsemi.com>
Cc: ipslinux@adaptec.com
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Intentionally keeping all register reads/writes.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/ips.c: In function ‘ips_init_copperhead’:
drivers/scsi/ips.c:4700:10: warning: variable ‘ConfigByte’ set but not used [-Wunused-but-set-variable]
4700 | uint8_t ConfigByte[IPS_MAX_CONFIG_BYTES];
| ^~~~~~~~~~
drivers/scsi/ips.c: In function ‘ips_init_copperhead_memio’:
drivers/scsi/ips.c:4794:10: warning: variable ‘ConfigByte’ set but not used [-Wunused-but-set-variable]
4794 | uint8_t ConfigByte[IPS_MAX_CONFIG_BYTES];
| ^~~~~~~~~~
drivers/scsi/ips.c: In function ‘ips_init_phase1’:
drivers/scsi/ips.c:6839:10: warning: variable ‘func’ set but not used [-Wunused-but-set-variable]
6839 | uint8_t func;
| ^~~~
drivers/scsi/ips.c:6838:10: warning: variable ‘bus’ set but not used [-Wunused-but-set-variable]
6838 | uint8_t bus;
| ^~~
Link: https://lore.kernel.org/r/20200723122446.1329773-13-lee.jones@linaro.org
Cc: Adaptec OEM Raid Solutions <aacraid@microsemi.com>
Cc: ipslinux@adaptec.com
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/qedi/qedi_main.c: In function ‘qedi_queue_cqe’:
drivers/scsi/qedi/qedi_main.c:1158:21: warning: variable ‘conn’ set but not used [-Wunused-but-set-variable]
1158 | struct iscsi_conn *conn;
| ^~~~
drivers/scsi/qedi/qedi_main.c: In function ‘__qedi_probe’:
drivers/scsi/qedi/qedi_main.c:2432:6: warning: variable ‘tmp’ set but not used [-Wunused-but-set-variable]
2432 | u16 tmp;
| ^~~
Link: https://lore.kernel.org/r/20200723122446.1329773-12-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@cavium.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/bnx2i/bnx2i_sysfs.c:40: warning: Function parameter or member 'attr' not described in 'bnx2i_show_sq_info'
drivers/scsi/bnx2i/bnx2i_sysfs.c:60: warning: Function parameter or member 'attr' not described in 'bnx2i_set_sq_info'
drivers/scsi/bnx2i/bnx2i_sysfs.c:96: warning: Function parameter or member 'attr' not described in 'bnx2i_show_ccell_info'
drivers/scsi/bnx2i/bnx2i_sysfs.c:114: warning: Function parameter or member 'attr' not described in 'bnx2i_set_ccell_info'
Link: https://lore.kernel.org/r/20200723122446.1329773-9-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Cc: Anil Veerabhadrappa <anilgv@broadcom.com>
Cc: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/ufs/ufs-qcom.c:253: warning: Function parameter or member 'hba' not described in 'ufs_qcom_host_reset'
drivers/scsi/ufs/ufs-qcom.c:383: warning: Function parameter or member 'hba' not described in 'ufs_qcom_cfg_timers'
drivers/scsi/ufs/ufs-qcom.c:383: warning: Function parameter or member 'gear' not described in 'ufs_qcom_cfg_timers'
drivers/scsi/ufs/ufs-qcom.c:383: warning: Function parameter or member 'hs' not described in 'ufs_qcom_cfg_timers'
drivers/scsi/ufs/ufs-qcom.c:383: warning: Function parameter or member 'rate' not described in 'ufs_qcom_cfg_timers'
drivers/scsi/ufs/ufs-qcom.c:383: warning: Function parameter or member 'update_link_startup_timer' not described in 'ufs_qcom_cfg_timers'
drivers/scsi/ufs/ufs-qcom.c:1738: error: Cannot parse struct or union!
Link: https://lore.kernel.org/r/20200723122446.1329773-4-lee.jones@linaro.org
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_hbadisc.c:1209: warning: Function parameter or member 'phba' not described in 'lpfc_sli4_clear_fcf_rr_bmask'
drivers/scsi/lpfc/lpfc_hbadisc.c:1309: warning: Function parameter or member 'sw_name' not described in 'lpfc_sw_name_match'
drivers/scsi/lpfc/lpfc_hbadisc.c:1309: warning: Excess function parameter 'fab_name' description in 'lpfc_sw_name_match'
drivers/scsi/lpfc/lpfc_hbadisc.c:1397: warning: Function parameter or member 'fcf_rec' not described in 'lpfc_copy_fcf_record'
drivers/scsi/lpfc/lpfc_hbadisc.c:1397: warning: Excess function parameter 'fcf' description in 'lpfc_copy_fcf_record'
drivers/scsi/lpfc/lpfc_hbadisc.c:1956: warning: Cannot understand lpfc_sli4_fcf_record_match - testing new FCF record for matching existing FCF
on line 1956 - I thought it was a doc line
drivers/scsi/lpfc/lpfc_hbadisc.c:2078: warning: Function parameter or member 'fcf_index' not described in 'lpfc_sli4_fcf_pri_list_del'
drivers/scsi/lpfc/lpfc_hbadisc.c:2109: warning: Function parameter or member 'fcf_index' not described in 'lpfc_sli4_set_fcf_flogi_fail'
drivers/scsi/lpfc/lpfc_hbadisc.c:2135: warning: Function parameter or member 'fcf_index' not described in 'lpfc_sli4_fcf_pri_list_add'
drivers/scsi/lpfc/lpfc_hbadisc.c:2135: warning: Function parameter or member 'new_fcf_record' not described in 'lpfc_sli4_fcf_pri_list_add'
Link: https://lore.kernel.org/r/20200723122446.1329773-3-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_els.c:3619: warning: Function parameter or member 't' not described in 'lpfc_els_retry_delay'
drivers/scsi/lpfc/lpfc_els.c:3619: warning: Excess function parameter 'ptr' description in 'lpfc_els_retry_delay'
drivers/scsi/lpfc/lpfc_els.c:4877: warning: Function parameter or member 'rejectError' not described in 'lpfc_els_rsp_reject'
drivers/scsi/lpfc/lpfc_els.c:7900: warning: Function parameter or member 't' not described in 'lpfc_els_timeout'
drivers/scsi/lpfc/lpfc_els.c:7900: warning: Excess function parameter 'ptr' description in 'lpfc_els_timeout'
drivers/scsi/lpfc/lpfc_els.c:8272: warning: Function parameter or member 'payload' not described in 'lpfc_send_els_event'
drivers/scsi/lpfc/lpfc_els.c:8272: warning: Excess function parameter 'cmd' description in 'lpfc_send_els_event'
drivers/scsi/lpfc/lpfc_els.c:8355: warning: Function parameter or member 'tlv' not described in 'lpfc_els_rcv_fpin_li'
drivers/scsi/lpfc/lpfc_els.c:8355: warning: Excess function parameter 'lnk_not' description in 'lpfc_els_rcv_fpin_li'
drivers/scsi/lpfc/lpfc_els.c:9688: warning: Function parameter or member 't' not described in 'lpfc_fabric_block_timeout'
drivers/scsi/lpfc/lpfc_els.c:9688: warning: Excess function parameter 'ptr' description in 'lpfc_fabric_block_timeout'
Link: https://lore.kernel.org/r/20200723122446.1329773-2-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Also move the header block above the correct function.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/cxgbi/cxgb3i/cxgb3i.c:390: warning: Function parameter or member 'dev' not described in 'arp_failure_skb_discard'
drivers/scsi/cxgbi/cxgb3i/cxgb3i.c:390: warning: Function parameter or member 'skb' not described in 'arp_failure_skb_discard'
drivers/scsi/cxgbi/cxgb3i/cxgb3i.c:390: warning: Excess function parameter 'c3cn' description in 'arp_failure_skb_discard'
drivers/scsi/cxgbi/cxgb3i/cxgb3i.c:390: warning: Excess function parameter 'req_completion' description in 'arp_failure_skb_discard'
drivers/scsi/cxgbi/cxgb3i/cxgb3i.c:895: warning: Function parameter or member 'csk' not described in 'l2t_put'
drivers/scsi/cxgbi/cxgb3i/cxgb3i.c:895: warning: Excess function parameter 'c3cn' description in 'l2t_put'
Link: https://lore.kernel.org/r/20200721164148.2617584-41-lee.jones@linaro.org
Cc: Karen Xie <kxie@chelsio.com>
Cc: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Only declare 'tp' and 'lp' if they are going to be used.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/sym53c8xx_2/sym_hipd.c: In function ‘sym_complete_error’:
drivers/scsi/sym53c8xx_2/sym_hipd.c:5356:18: warning: variable ‘lp’ set but not used [-Wunused-but-set-variable]
drivers/scsi/sym53c8xx_2/sym_hipd.c: In function ‘sym_complete_ok’:
drivers/scsi/sym53c8xx_2/sym_hipd.c:5485:18: warning: variable ‘lp’ set but not used [-Wunused-but-set-variable]
Link: https://lore.kernel.org/r/20200721164148.2617584-39-lee.jones@linaro.org
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Gerard Roudier <groudier@free.fr>
Cc: Wolfgang Stanglmeier <wolf@cologne.de>
Cc: Stefan Esser <se@mi.Uni-Koeln.de>
Cc: Richard Waltham <dormouse@farsrobt.demon.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
