Sparse reports the following issue:
CHECK drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:500:26: warning: incorrect type in initializer (different base types)
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:500:26: expected restricted __le32 [usertype] *pdesc
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:500:26: got unsigned int [usertype] *
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604005733.7905-3-Larry.Finger@lwfinger.net
Add a set of logic with corresponding coexistence parameters to
handle the situation under BT inquiry/page.
We will set PSTDMA while WL-Busy + BT inquiry/page to separate
WL/BT slots. PSTDMA can protect WL data rate and BT performance.
If WL-Busy + BT inquiry/page and there was BT device paired,
We will set the mechanism to 4Slot PSTDMA.
In 4Slot PSTDMA, the paired devices can perform more smoothly
and prevent some issues trigger from insufficient data.
And to avoid A2DP glitch or disconnection, we will adjust ACL
data priority higher than inquiry/page.
In addition, we found sometimes BT inquiry/page still working
last for seconds after BT had notified inquiry/page finished.
It will lead to A2DP glitch cause of ACL data, inquiry/page
priority toggled. To fix the corner, we add a timer to remain
the inquiry/page status.
And we found WL busy/idle threshold is too sensitive,
it will keep switching in some weak network environment and
coexistence mechanism will switch between TDMA and PSTDMA.
The very frequently switching may destroyed not only the
handshake with AP, but BT performance. And it will trigger
some unexpected error.
To prevent the frequently switching, we add a timer to delay
the status change while WL busy switch to idle.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200715023324.8600-1-yhchuang@realtek.com
ENOTSUPP (double PP) is internal linux kernel code 524 available only in
kernel include file linux/errno.h and not exported to userspace.
EOPNOTSUPP (OP; double PP) is standard code 95 for reporting 'operation not
supported' available via kernel include file uapi/asm-generic/errno.h.
ENOTSUP (single P) is alias for EOPNOTSUPP defined only in userspace
include file bits/errno.h and not available in kernel.
Because Linux kernel does not support ENOTSUP (single P) and because
userspace does not support ENOTSUPP (double PP), report error code for
'operation not supported' via EOPNOTSUPP macro.
This patch fixes problem that mwifiex kernel driver sends to userspace
unsupported error codes like: "failed: -524 (No error information)".
After applying this patch userspace see: "failed: -95 (Not supported)".
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200703112151.18917-1-pali@kernel.org
We currently have a collection of flags and locking between the
threaded irq and tx work:
- wl->flags bitops
- wl->mutex
- wl->wl_lock spinlock
The bitops flags do not need a spinlock around them, and we only need
the spinlock to see if we need to queue tx work or not. And wlcore_irq()
holds the mutex.
To simplify the locking, we can use spin_trylock and always queue tx
work unless we know there's nothing to do.
Let's also update the comment a bit while at it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200702162951.45392-4-tony@atomide.com
We currently have a collection of flags and locking between the
threaded irq and tx work:
- wl->flags bitops
- wl->mutex
- wl->wl_lock spinlock
The bitops flags do not need a spinlock around them, and
wlcore_irq() already holds the mutex calling wlcore_irq_locked().
And we only need the spinlock to see if we need to run the queue
or not.
To simplify the locking, we can use spin_trylock and always run the
tx queue unless we know there's nothing to do.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200702162951.45392-3-tony@atomide.com
We can simplify the runtime resume ELP path by always setting and
clearing the completion in runtime resume. This way we can test for
WL1271_FLAG_IRQ_RUNNING after the resume write to see if we need
completion at all.
And in wlcore_irq(), we need to take spinlock for running the
completion and for the pm_wakeup_event(). Spinlock is not needed
around the bitops flags check for WL1271_FLAG_SUSPENDED so the
spinlocked sections get shorter.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200702162951.45392-2-tony@atomide.com
Some platforms cannot read the DBI register successfully for the
ASPM settings. After the read failed, the bus could be unstable,
and the device just became unavailable [1]. For those platforms,
the ASPM should be disabled. But as the ASPM can help the driver
to save the power consumption in power save mode, the ASPM is still
needed. So, add a module parameter for them to disable it, then
the device can still work, while others can benefit from the less
power consumption that brings by ASPM enabled.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=206411
[2] Note that my lenovo T430 is the same.
Fixes: 3dff7c6e37 ("rtw88: allows to enable/disable HCI link PS mechanism")
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200605074703.32726-1-yhchuang@realtek.com
Beamforming is used for directional signal transmission/reception.
Beamformee plays the role for signal reception, and makes the RX
performance better in middle distance range.
Implement beamformee related callbacks for 8821c.
Since 8821c only support 1ss rate, nc_index in beamformee setting
needs to be adjusted based on the capability.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-4-yhchuang@realtek.com
The TX power requires to be adjusted based on the thermal value.
The actual power will decrease if the thermal value raised, and
will increase if the thermal value lowered. Driver comapres the
thermal value, as moving averages. If it changes over a limit,
driver will modify the TX power index to compensate.
Implement rtw_chip_ops::pwr_track() for 8821c.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-3-yhchuang@realtek.com
CCK PD can reduce the number of false alarm of the CCK rates.
It dynamically adjusts the power threshold and CS ratio.
The values are compared to the values of the previous level, if
the level is changed, set new values of power threshold and CS
ratio.
Implement rtw_chip_ops::cck_pd_set() for 8821c.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-2-yhchuang@realtek.com
Straightforward conversion to new infra, 1 VxLAN port, handler
may sleep.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Covert to new infra. Looks like this driver was not doing
ref counting, and sleeping in the callback.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Straightforward conversion to new infra. Driver restores info
after close/open cycle by calling its internal restore function
so just use that, no need for udp_tunnel_nic_reset_ntf() here.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Carbon copy of the previous change.
This driver is just a super thin FW interface, but Derek let us
know the table has 1024 entries.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is just a super thin FW interface, but Derek let us
know the table has 1024 entries.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to new infra, now the refcounting will be correct,
and driver gets port replay of other ports when offloaded
port gets removed.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to new infra, this driver is very simple. The check of
adapter->rawf_cnt in cxgb_udp_tunnel_unset_port() is kept from
the old port deletion function but it's dodgy since nothing ever
updates that member once its set during init. Also .set_port
callback always adds the raw mac filter..
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fairly straightforward conversion - no need to keep track
of the use count, and replay when ports get removed, also
callbacks can just sleep.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the new udp_tunnel_nic infra. Don't clear the features
when VxLAN port is not present to make all drivers behave the same.
Driver will now (until we address the problem in the core) leave
the RX UDP tunnel feature always on, since this is what most drivers
do.
Remove the list of VxLAN ports, just program the one core told us to.
The driver seem to want to clear the VxLAN ports on close but it
doesn't seem to flush the port list properly so it'd get wrong
use counts after close/open. Again since it calls its own open
handler we need the reset notification hack.
v2:
- fix kbuild warning
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of looping though the list of ports just check
if the geometry of the packet is correct for VxLAN.
HW most likely doesn't care about the exact port, anyway,
since only first port is actually offloaded, and this way
we won't have to maintain the port list at all.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert be2net to new udp_tunnel_nic infra. NIC only takes one VxLAN
port. Remove the port tracking using a list. The warning in
be_work_del_vxlan_port() looked suspicious - like the driver expected
ports to be removed in order of addition.
be2net unregisters ports when going down and re-registers them (for
skyhawk) when coming up, but it never checks if the device is up
in the add_port / del_port callbacks. Make it use
UDP_TUNNEL_NIC_INFO_OPEN_ONLY. Sadly this driver calls its own
open/close functions directly so the udp_tunnel_nic_reset_ntf()
workaround is needed.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP conversion is pretty straightforward. We want to be able
to sleep, and only get callbacks when the device is open.
NFP did not ask for port replay when ports were removed, now
new infra will provide this feature for free.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is likely firmware causing this but its starting to annoy customers.
Change the message level to verbose to prevent the spam.
Note that this seems to only show up with ISCSI enabled on the HBA via the
qedi driver.
Signed-off-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RTL8125B rev.b. In my tests 2.5Gbps worked well
w/o firmware, however for a stable link at 1Gbps firmware revision
0.0.2 is needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek assigned a new PHY ID for the RTL8125B-internal PHY.
It's however compatible with the RTL8125A-internal PHY.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx listener abstraction allows the switch driver (e.g.,
mlxsw_spectrum) to register a function that is called when a packet is
received (trapped) for a specific reason.
Up until now, the Rx listener lookup was solely based on the trap
identifier. However, when a packet is mirrored to the CPU the trap
identifier merely indicates that the packet was mirrored, but not why it
was mirrored. This makes it impossible for the switch driver to register
different Rx listeners for different mirror reasons.
Solve this by allowing the switch driver to register a Rx listener with
a mirror reason and by extending the Rx listener lookup to take the
mirror reason into account.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the mirror reason is valid, retrieve it into the Rx information
so that it could be used during listener lookup in a later patch.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Completion Queue Element version 2 (CQEv2) includes a field called
'mirror_reason' which indicates why the packet was mirrored to the CPU.
Add the field so that it can be used by a later patch.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets that are mirrored to the CPU port are trapped with one of eight
trap identifiers. Add them.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
