For an overview of the race created by this patch goto synchronization
label.
In napi busy-poll mode, the kernel invokes the napi handler of the
device repeatedly to poll the NIC's receive queues. This process
repeats until a timeout, specific for each connection, is up.
By polling packets in busy-poll mode the user may gain lower latency
and higher throughput (since the kernel no longer waits for interrupts
to poll the queues) in expense of CPU usage.
Upon completing a napi routine, the driver checks whether
the routine was called by an interrupt handler. If so, the driver
re-enables interrupts for the device. This is needed since an
interrupt routine invocation disables future invocations until
explicitly re-enabled.
The driver avoids re-enabling the interrupts if they were not disabled
in the first place (e.g. if driver in busy mode).
Originally, the driver checked whether interrupt re-enabling is needed
by reading the 'ena_napi->unmask_interrupt' variable. This atomic
variable was set upon interrupt and cleared after re-enabling it.
In the 4.10 Linux version, the 'napi_complete_done' call was changed
so that it returns 'false' when device should not re-enable
interrupts, and 'true' otherwise. The change includes reading the
"NAPIF_STATE_IN_BUSY_POLL" flag to check if the napi call is in
busy-poll mode, and if so, return 'false'.
The driver was changed to re-enable interrupts according to this
routine's return value.
The Linux community rejected the use of the
'ena_napi->unmaunmask_interrupt' variable to determine whether
unmasking is needed, and urged to use napi_napi_complete_done()
return value solely.
See https://lore.kernel.org/patchwork/patch/741149/ for more details
As explained, a busy-poll session exists for a specified timeout
value, after which it exits the busy-poll mode and re-enters it later.
This leads to many invocations of the napi handler where
napi_complete_done() false indicates that interrupts should be
re-enabled.
This creates a bug in which the interrupts are re-enabled
unnecessarily.
To reproduce this bug:
1) echo 50 | sudo tee /proc/sys/net/core/busy_poll
2) echo 50 | sudo tee /proc/sys/net/core/busy_read
3) Add counters that check whether
'ena_unmask_interrupt(tx_ring, rx_ring);'
is called without disabling the interrupts in the first
place (i.e. with calling the interrupt routine
ena_intr_msix_io())
Steps 1+2 enable busy-poll as the default mode for new connections.
The busy poll routine rearms the interrupts after every session by
design, and so we need to add an extra check that the interrupts were
masked in the first place.
synchronization:
This patch introduces a race between the interrupt handler
ena_intr_msix_io() and the napi routine ena_io_poll().
Some macros and instruction were added to prevent this race from leaving
the interrupts masked. The following specifies the different race
scenarios in this patch:
1) interrupt handler and napi routine run sequentially
i) interrupt handler is called, sets 'interrupts_masked' flag and
successfully schedules the napi handler via softirq.
In this scenario the napi routine might not see the flag change
for several reasons:
a) The flag is stored in a register by the compiler. For this
case the WRITE_ONCE macro which prevents this.
b) The compiler might reorder the instruction. For this the
smp_wmb() instruction was used which implies a compiler memory
barrier.
c) On archs with weak consistency model (like ARM64) the napi
routine might be scheduled and start running before the flag
STORE instruction is committed to cache/memory. To ensure this
doesn't happen, the smp_wmb() instruction was added. It ensures
that the flag set instruction is committed before scheduling
napi.
ii) compiler reorders the flag's value check in the 'if' with
the flag set in the napi routine.
This scenario is prevented by smp_rmb() call after the flag check.
2) interrupt handler and napi routine run in parallel (can happen when
busy poll routine invokes the napi handler)
i) interrupt handler sets the flag in one core, while the napi
routine reads it in another core.
This scenario also is divided into two cases:
a) napi_complete_done() doesn't finish running, in which case
napi_sched() would just set NAPIF_STATE_MISSED and the napi
routine would reschedule itself without changing the flag's value.
b) napi_complete_done() finishes running. In this case the
napi routine might override the flag's value.
This doesn't present any rise since it later unmasks the
interrupt vector.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Free ILT lines used for XRC-SRQ's contexts.
- Free XRCD bitmap
Fixes: b8204ad878 ("qed: changes to ILT to support XRC")
Fixes: 7bfb399eca ("qed: Add XRC to RoCE")
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Yuval Basson <ybason@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing "ip link set dev ... up" for a ksz9477 backed link,
ksz9477_phy_setup is called and it calls phy_remove_link_mode to remove
1000baseT HDX. During phy_remove_link_mode, phy_advertise_supported is
called. Doing so reverts any previous change to advertised link modes
e.g. using a udevd .link file.
phy_remove_link_mode is not meant to be used while opening a link and
should be called during phy probe when the link is not yet available to
userspace.
Therefore move the phy_remove_link_mode calls into
ksz9477_switch_register. It indirectly calls dsa_register_switch, which
creates the relevant struct phy_devices and we update the link modes
right after that. At that time dev->features is already initialized by
ksz9477_switch_detect.
Remove phy_setup from ksz_dev_ops as no users remain.
Link: https://lore.kernel.org/netdev/20200715192722.GD1256692@lunn.ch/
Fixes: 42fc6a4c61 ("net: dsa: microchip: prepare PHY for proper advertisement")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, PF queries the MAC link status per second by calling
function hclge_get_mac_link_status(). It return the error code
when failed to send cmdq command to firmware. It's incorrect,
because this return value is used as the MAC link status, which
0 means link down, and none-zero means link up. So fixes it.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The content of the TX desc is automatically cleared by the HW
when the HW has sent out the packet to the wire. When desc filling
fails in hns3_nic_net_xmit(), it will call hns3_clear_desc() to do
the error handling, which miss zeroing of the TX desc and the
checking if a unmapping is needed.
So add the zeroing and checking in hns3_clear_desc() to avoid the
above problem. Also add DESC_TYPE_UNKNOWN to indicate the info in
desc_cb is not valid, because hns3_nic_reclaim_desc() may treat
the desc_cb->type of zero as packet and add to the sent pkt
statistics accordingly.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With GRO and fraglist support, the SKB can be aggregated to
a total size of 65535, and when that SKB is forwarded through
a bridge, the size of the SKB may be pushed to exceed the size
of 65535 when br_dev_queue_push_xmit() is called.
The max send size of BD supported by the HW is 65535, when a SKB
with a headlen of over 65535 is sent to the driver, the driver
needs to use multi BD to send the linear data, and the send size
of the last BD is calculated incorrectly by the driver who is
using '&' operation, which causes a TX error.
Use '%' operation to fix this problem.
Fixes: 3fe13ed95d ("net: hns3: avoid mult + div op in critical data path")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a big TX buffer is sent using multi BD, the driver maps the
whole TX buffer, and unmaps it using info in desc_cb corresponding
to each BD, but only the info in the desc_cb of first BD is correct,
other info in desc_cb is wrong, which causes TX unmapping problem
when SMMU is on.
Only set the mapping and freeing info in the desc_cb of first BD to
fix this problem, because the TX buffer only need to be unmapped and
freed once.
Fixes: 1e8a7977d09f("net: hns3: add handling for big TX fragment")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huzhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an interface to configure the advertisement for a clause 22 PCS
PHY, and set the AN enable flag in the BMCR appropriately.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a way for MAC PCS to have private data while keeping independence
from struct phylink_config, which is used for the MAC itself. We need
this independence as we will have stand-alone code for PCS that is
independent of the MAC. Introduce struct phylink_pcs, which is
designed to be embedded in a driver private data structure.
This structure does not include a mdio_device as there are PCS
implementations such as the Marvell DSA and network drivers where this
is not necessary.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
With PCS support, how we implement interface reconfiguration (or other
major reconfiguration) is not up to the job; we end up reconfiguring
the PCS for an interface change while the link could potentially be up.
In order to solve this, add two additional MAC methods for major
configuration, one to prepare for the change, and one to finish the
change.
This allows mvneta and mvpp2 to shutdown what they require prior to the
MAC and PCS configuration calls, and then restart as appropriate.
This impacts ksettings_set(), which now needs to identify whether the
change is a minor tweak to the advertisement masks or whether the
interface mode has changed, and call the appropriate function for that
update.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-code the pause in-band advertisement update in light of the addition
of PCS support, so that we perform the minimum required; only the PCS
configuration function needs to be called in this case, followed by the
request to trigger a restart of negotiation if the programmed
advertisement changed.
We need to change the pcs_config() signature to pass whether resolved
pause should be passed to the MAC for setups such as mvneta and mvpp2
where doing so overrides the MAC manual flow controls.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
For fixed links, we only allow the current settings, so this should be
a matter of merely rejecting an attempt to change the settings. If the
settings agree, then there is nothing more we need to do.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we have a PHY attached, an ethtool ksettings_set() call only
really needs to call through to the phylib equivalent; phylib will
call back to us when the link changes so we can update our state.
Therefore, we can bypass most of our ksettings_set() call for this
case.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the ksettings_set() implementation to look more like phylib's
implementation; use a switch() for validating the autoneg setting, and
use the linkmode_modify() helper to set the autoneg bit in the
advertisement mask.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only PHYs that are used with phylink which change their interface
are the BCM84881 and MV88X3310 family, both of which only change their
interface modes on link-up events. This will break when drivers are
converted to split-PCS. Fix this.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only PHYs that are used with phylink which change their interface
are the BCM84881 and MV88X3310 family, both of which only change their
interface modes on link-up events. However, rather than relying upon
this behaviour by the PHY, we should give a stronger guarantee when
resolving that the link will be down whenever we change the interface
mode. This patch implements that stronger guarantee for resolve.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a boolean to indicate whether mac_config() should be called during
a resolution. This allows resolution to have a single location where
mac_config() will be called, which will allow us to make decisions
about how and what we do.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Comparing the ethtool output from phylink and non-phylink fixed-link
setups shows that we have some differences:
- The "auto-negotiation" fields are different; phylink reports these
as "No", non-phylink reports these as "Yes" for the supported and
advertising masks.
- The link partner advertisement is set to the link speed with non-
phylink, but phylink leaves this unset, causing all link partner
fields to be omitted.
The phylink ethtool output also disagrees with the software emulated
PHY dump via the MII registers.
Update the phylink fixed-link parsing code so that we better reflect
the behaviour of the non-phylink code that this facility replaces, and
bring the ethtool interface more into line with the report from via the
MII interface.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the generic dynamic interrupt moderation (dim)
framework to implement adaptive interrupt coalescing
on Rx. With the per-packet interrupt scheme, a high
interrupt rate has been noted for moderate traffic flows
leading to high CPU utilization. The 'dim' scheme
implemented by the current patch addresses this issue
improving CPU utilization while using minimal coalescing
time thresholds in order to preserve a good latency.
On the Tx side use an optimal time threshold value by
default. This value has been optimized for Tx TCP
streams at a rate of around 85kpps on a 1G link,
at which rate half of the Tx ring size (128) gets filled
in 1500 usecs. Scaling this down to 2.5G links yields
the current value of 600 usecs, which is conservative
and gives good enough results for 1G links too (see
next).
Below are some measurement results for before and after
this patch (and related dependencies) basically, for a
2 ARM Cortex-A72 @1.3Ghz CPUs system (32 KB L1 data cache),
using 60secs log netperf TCP stream tests @ 1Gbit link
(maximum throughput):
1) 1 Rx TCP flow, both Rx and Tx processed by the same NAPI
thread on the same CPU:
CPU utilization int rate (ints/sec)
Before: 50%-60% (over 50%) 92k
After: 13%-22% 3.5k-12k
Comment: Major CPU utilization improvement for a single flow
Rx TCP flow (i.e. netperf -t TCP_MAERTS) on a single
CPU. Usually settles under 16% for longer tests.
2) 4 Rx TCP flows + 4 Tx TCP flows (+ pings to check the latency):
Total CPU utilization Total int rate (ints/sec)
Before: ~80% (spikes to 90%) ~100k
After: 60% (more steady) ~4k
Comment: Important improvement for this load test, while the
ping test outcome does not show any notable
difference compared to before.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable programming of the interrupt coalescing registers
and allow manual configuration of the coalescing time
thresholds via ethtool. Packet thresholds have been fixed
to predetermined values as there's no point in making them
run-time configurable, also anticipating the dynamic interrupt
moderation (DIM) algorithm which uses fixed packet thresholds
as well. If the interface is up when the operation mode of
traffic interrupt events is changed by the user (i.e. switching
from default per-packet interrupts to coalesced interrupts),
the traffic needs to be paused in the process.
This patch also prepares the ground for introducing DIM on Rx.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'struct enetc_bdr' is already '____cacheline_aligned_in_smp'.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupt coalescing registers naming in the current revision
of the Ref Man (RM) is ICR, deprecating the ICIR name used
in earlier (draft) versions of the RM.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A reliable traffic pause (and reconfiguration) procedure
is needed to be able to safely make h/w configuration
changes during run-time, like changing the mode in which the
interrupts are operating (i.e. with or without coalescing),
as opposed to making on-the-fly register updates that
may be subject to h/w or s/w concurrency issues.
To this end, the code responsible of the run-time device
configurations that basically starts resp. stops the traffic
flow through the device has been extracted from the
the enetc_open/_close procedures, to the separate standalone
enetc_start/_stop procedures. Traffic stop should be as
graceful as possible, it lets the executing napi threads to
to finish while the interrupts stay disabled. But since
the napi thread will try to re-enable interrupts by clearing
the device's unmask register, the enable_irq/ disable_irq
API has been used to avoid this potential concurrency issue
and make the traffic pause procedure more reliable.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's time to differentiate between Rx and Tx ring sizes.
Not only Tx rings are processed differently than Rx rings,
but their default number also differs - i.e. up to 8 Tx rings
per device (8 traffic classes) vs. 2 Rx rings (one per CPU).
So let's set Tx rings sizes to half the size of the Rx rings
for now, to be conservative.
The default ring sizes were decreased as well (to the next
lower power of 2), to reduce the memory footprint, buffering
etc., since the measurements I've made so far show that the
rings are very unlikely to get full.
This change also anticipates the introduction of the
dynamic interrupt moderation (dim) algorithm which operates
on maximum packet thresholds of 256 packets for Rx and 128
packets for Tx.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_gpiod_get_array() to simplify the error handling and exit
code path.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the report of [1], this driver is possible to cause
the following error in ravb_tx_timeout_work().
ravb e6800000.ethernet ethernet: failed to switch device to config mode
This error means that the hardware could not change the state
from "Operation" to "Configuration" while some tx and/or rx queue
are operating. After that, ravb_config() in ravb_dmac_init() will fail,
and then any descriptors will be not allocaled anymore so that NULL
pointer dereference happens after that on ravb_start_xmit().
To fix the issue, the ravb_tx_timeout_work() should check
the return values of ravb_stop_dma() and ravb_dmac_init().
If ravb_stop_dma() fails, ravb_tx_timeout_work() re-enables TX and RX
and just exits. If ravb_dmac_init() fails, just exits.
[1]
https://lore.kernel.org/linux-renesas-soc/20200518045452.2390-1-dirk.behme@de.bosch.com/
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the implementation of __mt76x02u_mcu_send_msg() the skb is consumed
all execution paths except one. Release skb before returning if
test_bit() fails.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Free the second mcu skb if __mt76_mcu_skb_send_msg() fails to transmit
the first one in mt7615_mcu_wtbl_sta_add().
Fixes: 99c457d902 ("mt76: mt7615: move mt7615_mcu_set_bmc to mt7615_mcu_ops")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to avoid possible overflows, move tx queue accounting from
mt7663s_tx_run_queue() to mt76s_tx_queue_skb_raw()/mt76s_tx_queue_skb()
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7663-usb-sdio-common module as container for shared
code between usb and sdio driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As usb, sdio relies on mt76 workqueue to configure tx rate or upload
keys to the hw. This is a preliminary patch to add SDIO support to
mt76 driver
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_skb_adjust_pad to reuse the code adding sdio support to
mt7615 driver and remove code duplication. Move 4B header configuration
for usb devices out of mt76_skb_adjust_pad
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
usb and sdio relies on SF architecture. This is a preliminary patch to
add SDIO support to mt76 driver
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Smatch complains that "wcidx" value comes from the network and thus
cannot be trusted. In this case, it actually seems to come from the
firmware. If your wireless firmware is malicious then probably no
amount of carefulness can protect you.
On the other hand, these days we still try to check the firmware as much
as possible. Verifying that the index is within bounds will silence a
static checker warning. And it's harmless and a good exercise in kernel
hardening. So I suggest that we do add a bounds check.
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix potential memory leak in mcu message handler on error condition.
Fixes: 0e6a29e477 ("mt76: mt7615: add support to read temperature from mcu")
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix potential memory leak in mcu message handler on error condition.
Fixes: eb99cc95c3 ("mt76: mt7615: introduce mt7663u support")
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reschedule runtime-pm delayed work if there is a new activity when ps
delayed work is already scheduled
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not schedule ps_work during hw scanning or hw scheduled frequency
scan
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On usb device rate configuration for sampling is performed relying on a
workqueue since it is not possible to access the device in the interrupt
context. Move the configuration of the probe_rate flag in the workqueue
in order to keep probe sampling in sync with actual rate configuration
Fixes: eb99cc95c3 ("mt76: mt7615: introduce mt7663u support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7615_driver_own can fail if it runs too close to mt7615_fw_own. In
order to improve mt7615_driver_own reliability, retry to get runtime-pm
ownership if mt7615_driver_own fails
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce idle-timeout knob in mt7615 debugfs in order to configure the
idle time to switch to low-power state
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to reduce number of received interrupts and power consumption,
enable hw beacon filter if runtime-pm is enabled
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
