Introduce mt76_skb_adjust_pad to reuse the code adding sdio support to
mt7615 driver and remove code duplication. Move 4B header configuration
for usb devices out of mt76_skb_adjust_pad
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_update_survey utility routine in order to compute
survey stats without waking up the device since it runs holding mt76 lock.
Run mt7615_pm_wake directly in mt7615_update_channel since it can run
with mt76.mutex held if called by mac80211
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_pm_wake utility routine to wake the device from
runtime low-power state (lower-power state is currently supported by
offload firmware for pcie devices).
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76 workqueue from usb to common code in order to be reused adding
low-power support for mt7663 chipset
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This can be used for calibration in the manufacturing process.
It supports sending a configurable number of packets with a specific rate
and configurable tx power levels / antenna settings.
It also supports receiving packets and showing some statistics, including
packet counters and detailed RSSI information.
It will only be compiled in if CONFIG_NL80211_TESTMODE is enabled
Signed-off-by: Felix Fietkau <nbd@nbd.name>
All drivers use this in pretty much the same way. Moving it to core helps with
some checks for the upcoming testmode support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Overwrite hw queue id for non-bufferable management frames if the hw
support always txq (altxq) in order to be in sync with mac txwi code
Fixes: cdad487405 ("mt76: mt7615: add dma and tx queue initialization for MT7622")
Fixes: f40ac0f3d3 ("mt76: mt7615: introduce mt7663e support")
Suggested-by: Felix Fietkau <nbd@nbd.name>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76 core uses ffs() to find the next free bit. This works well for 32 bit
architectures where BITS_PER_LONG is 32. ffs only checks 32 bit values, so
allocation fails on 64 bit architectures.
Additionally, the wcid mask array was too small in cases where the array
was not a multiple of BITS_PER_LONG.
Fix this by making the wcid mask array u32 instead and use DIV_ROUND_UP
for the size, just in case we ever bump it to a value that's not a multiple
of 32.
Reported-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
switch to per-vif ps support since mt7615 offload firmware can handle it
properly. This patch allows enabling/disabling power-save support on p2p
interface
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The newer 802.11ax devices (i.e. MT7915E) can connect to much more
peers than previous generations.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Tested on Chromebok by "echo mem to /sys/power/state" to suspend and
then waked up by keyboard keystrokes to resume system.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce support for mt7663u 802.11ac 2x2:2 chipset to mt7615 driver.
Main difference respect to pcie code base is the usb code needs to
configure wtbl from non-atomic context
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce headroom and tailroom to mt76_mcu_ops data structure in order
to unify the routine used for mcu message allocation. This is a
preliminary patch to add mt7663u support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If a MCU timeout occurs before a hw restart completes, another hw restart
is scheduled, and the station state gets corrupted.
To speed up dealing with that, do not issue any MCU commands after the first
timeout, and defer handling timeouts until the reset has completed.
Also ignore errors in MCU commands during start/config to avoid making user
space fail on this condition. If it happens, another restart is scheduled
quickly, and that usually recovers the hardware properly.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_mcu_send_message routine in order to allocate mcu skb
out of mcu sending routine. This approach is useful when the mcu
message is complicated and it is convenient to rely on skb buffer API
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_mcu data structure to contain common fields between
mt76u_mcu and mt76e_mcu.
Initialize mcu common fields in mt76_alloc_device().
Rely on mt76_mcu in mt76_mcu_rx_event and in mt76_mcu_get_response
in order to reuse them in usb code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rename usb stat_wq in wq in order to be reused not just for gathering hw
tx statistics
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Set RX scatter gather number to 4 in order to extend the maximum AMSDU
size to 11,454.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify code converting between the different txpower values. Always add/remove
the combined txpower delta before dividing half-dB values.
Also fix the combined txpower delta values. The correct half-dB delta for
3 chains is 9, not 8.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the firmware detects a problem, it needs the host to stop/reset DMA and
resume it again when the hardware state has been reset.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Define MT_DRV_RX_DMA_HDR flag in drv_flag in order to not skip rx frame
dma header since new devices (e.g. mt7663u) reports rx frame info in the
usb dma header
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76u_skb_dma_info utility routine in mt76-usb module in order
to be reused adding mt7663u support
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce extended utility routines to read/write data o usb bus. New
devices (e.g. mt7663u) will rely on both upper and lower part of the
register address. Add ext parameter to mt76u_init signature in order to
reuse the code adding mt7663u support.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76u_alloc_mcu_queue utility routine to allocate mcu hw rx queue.
This is a preliminary patch to support new devices (e.g. mt7663u) that
rely on a hw queue for mcu messages
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For transferring data over USB the optimal size is endpoint maxpacket.
For my hardware maxpaket for control endpoint is 64 bytes and changing
to this value from 128 bytes further shorten TBTT work time from
3ms to 1ms.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use larger batches for usb copy to speed this operation up. Otherwise it
would be too slow for copying new beacons or broadcast frames over usb.
Assure, that always a multiple of 4 Bytes is copied, as outlined in
850e8f6fbd "mt76: round up length on mt76_wr_copy" from Felix Fietkau.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Before this patch, mt76 handled rx traffic for all TIDs equally,
when released from reorder buffer early. This patch uses an AC specific
reorder timeout, in order to release partial aggregated frames for video
ACs earlier. Voice ACs are currently not aggregated (thanks to Felix for
this hint). For example, ath10k also uses AC specific reorder timeouts
(reported by firmware in that case).
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
