It adds support for adreno a405 found on MSM8939. The adreno_is_a430()
check in adreno_submit() needs an extension to cover a405. The
downstream driver suggests it should cover the whole a4xx generation.
That's why it gets changed to adreno_is_a4xx(), while a420 is not
tested though.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Update the gmu_pdc registers for A640 and A650.
Some of the RSCC registers on A650 are in a separate region.
Note this also changes the address of these registers:
RSCC_TCS1_DRV0_STATUS
RSCC_TCS2_DRV0_STATUS
RSCC_TCS3_DRV0_STATUS
Based on the values in msm-4.14 and msm-4.19 kernels.
v3: replaced adreno_is_a650 around ->rscc with checks for "rscc" resource
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Newer GPUs have different GMU firmware path.
v3: updated a6xx_gmu_fw_load based on feedback, including gmu_write_bulk,
and removed extra whitespace change
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This gives more fine-grained control over how memory is allocated over the
DMA api. In particular, it allows using an address range or pinning to
a fixed address.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Writing to the devfreq sysfs nodes while the GPU is powered down can
result in a system crash (on a5xx) or a nasty GMU error (on a6xx):
$ /sys/class/devfreq/5000000.gpu# echo 500000000 > min_freq
[ 104.841625] platform 506a000.gmu: [drm:a6xx_gmu_set_oob]
*ERROR* Timeout waiting for GMU OOB set GPU_DCVS: 0x0
Despite the fact that we carefully try to suspend the devfreq device when
the hardware is powered down there are lots of holes in the governors that
don't check for the suspend state and blindly call into the devfreq
callbacks that end up triggering hardware reads in the GPU driver.
Call pm_runtime_get_if_in_use() in the gpu_busy() and gpu_set_freq()
callbacks to skip the hardware access if it isn't active.
v3: Only check pm_runtime_get_if_in_use() for == 0 per Eric Anholt
v2: Use pm_runtime_get_if_in_use() per Eric Anholt
Cc: stable@vger.kernel.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Maximum allowed bandwidth has no dependency on the type
of panel used. Hence, cleanup the code to use max_bw_high
as the threshold value for bandwidth checks.
Update the maximum allowed bandwidth as 6.8Gbps for
SC7180 target.
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This change adds support to scale src clk and bandwidth as
per composition requirements.
Interconnect registration for bw has been moved to mdp
device node from mdss to facilitate the scaling.
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This change adds support to configure dspp blocks in
the dpu driver.
Macro description of the changes coming in this patch.
1) Add dspp definitions in the hw catalog.
2) Add capability to reserve dspp blocks in the display data path.
3) Attach the reserved block to the encoder.
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Tested-by: Fritz Koenig <frkoenig@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
When allocation for mdp5_kms fails, calling mdp5_destroy() leads to undefined
behaviour, likely a nullptr exception or use-after-free troubles.
Signed-off-by: Roy Spliet <nouveau@spliet.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
rd_full should be defined outside the CONFIG_DEBUG_FS region, in order
to be able to link the msm driver even when CONFIG_DEBUG_FS is disabled.
Fixes: e515af8d4a ("drm/msm: devcoredump should dump MSM_SUBMIT_BO_DUMP buffers")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This
1) Enables core DRM syncobj support.
2) Adds options to the submission ioctl to wait/signal syncobjs.
Just like the wait fence fd, this does inline waits. Using the
scheduler would be nice but I believe it is out of scope for
this work.
Support for timeline syncobjs is implemented and the interface
is ready for it, but I'm not enabling it yet until there is
some code for turnip to use it.
The reset is mostly in there because in the presence of waiting
and signalling the same semaphores, resetting them after
signalling can become very annoying.
v2:
- Fixed style issues
- Removed a cleanup issue in a failure case
- Moved to a copy_from_user per syncobj
v3:
- Fixed a missing declaration introduced in v2
- Reworked to use ERR_PTR/PTR_ERR
- Simplified failure gotos.
Used by: https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/2769
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Using the following command will get compile warnings:
make W=1 drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.o ARCH=arm64
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c: In function
‘_dpu_crtc_program_lm_output_roi’:
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:91:19: warning: variable
‘dpu_crtc’ set but not used [-Wunused-but-set-variable]
struct dpu_crtc *dpu_crtc;
^~~~~~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c: In function
‘dpu_crtc_atomic_begin’:
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:428:35: warning: variable
‘smmu_state’ set but not used [-Wunused-but-set-variable]
struct dpu_crtc_smmu_state_data *smmu_state;
^~~~~~~~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c: In function
‘dpu_crtc_atomic_flush’:
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:489:25: warning: variable
‘event_thread’ set but not used [-Wunused-but-set-variable]
struct msm_drm_thread *event_thread;
^~~~~~~~~~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c: In function
‘dpu_crtc_destroy_state’:
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:565:19: warning: variable
‘dpu_crtc’ set but not used [-Wunused-but-set-variable]
struct dpu_crtc *dpu_crtc;
^~~~~~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c: In function
‘dpu_crtc_duplicate_state’:
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:664:19: warning: variable
‘dpu_crtc’ set but not used [-Wunused-but-set-variable]
struct dpu_crtc *dpu_crtc;
^~~~~~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c: In function
‘dpu_crtc_disable’:
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:693:26: warning: variable
‘priv’ set but not used [-Wunused-but-set-variable]
struct msm_drm_private *priv;
^~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:691:27: warning: variable
‘mode’ set but not used [-Wunused-but-set-variable]
struct drm_display_mode *mode;
^~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c: In function ‘dpu_crtc_enable’:
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:766:26: warning: variable
‘priv’ set but not used [-Wunused-but-set-variable]
struct msm_drm_private *priv;
^~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c: In function ‘dpu_crtc_init’:
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:1292:18: warning: variable
‘kms’ set but not used [-Wunused-but-set-variable]
struct dpu_kms *kms = NULL;
^~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:663: warning: Excess function
parameter 'Returns' description in 'dpu_crtc_duplicate_state'
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Hongbo Yao <yaohongbo@huawei.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
'in' is duplicated in the error message. Axe one of them.
While at it, slighly improve indentation.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This change adds MDP5 configuration for MSM8x36-based SoCs,
like MSM8936, 8939 and their APQ variants.
The configuration is based on MSM8916's, but adds some notable
features, like ad and pp blocks, along with some register
changes.
changes since v1:
- add an ad block
- add a second mixer @ 0x47000
- adjust .max_width
- write a more descriptive commit message
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
drivers/gpu/drm/drm_client_modeset.c: In function ‘drm_client_firmware_config’:
./include/linux/bits.h:26:28: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
__builtin_constant_p((l) > (h)), (l) > (h), 0)))
v2: Add a warning for passing connector_count==0 as this will hit an
infinite loop, so document the invalid parameter.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200516212330.13633-2-chris@chris-wilson.co.uk
When this flag is set in the CS IB flags, it causes
a memory cache flush of the GFX.
v2:
Move new flag to drm_amdgpu_cs_chunk_ib.flags
Bump up UAPI version
Remove condition on job != null to emit mem_sync
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
unified amdgpu device attribute node functions:
1. add some helper functions to create amdgpu device attribute node.
2. create device node according to device attr flags on different VF mode.
3. rename some functions name to adapt a new interface.
v2:
1. remove ATTR_STATE_DEAD, ATTR_STATE_ALIVE enum.
2. rename callback function perform to attr_update.
3. modify some variable names
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
the swsmu or powerplay(hwmgr) need to handle task according to different VF mode,
this function to help query vf mode.
vf mode:
1. SRIOV_VF_MODE_BARE_METAL: the driver work on host OS (PF)
2. SRIOV_VF_MODE_ONE_VF : the driver work on guest OS with one VF
3. SRIOV_VF_MODE_MULTI_VF : the driver work on guest OS with multi VF
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When GPU got timeout, it would notify an interested part
of an opportunity to dump info before actual GPU reset.
A usermode app would open 'autodump' node under debugfs system
and poll() for readable/writable. When a GPU reset is due,
amdgpu would notify usermode app through wait_queue_head and give
it 10 minutes to dump info.
After usermode app has done its work, this 'autodump' node is closed.
On node closure, amdgpu gets to know the dump is done through
the completion that is triggered in release().
There is no write or read callback because necessary info can be
obtained through dmesg and umr. Messages back and forth between
usermode app and amdgpu are unnecessary.
v2: (1) changed 'registered' to 'app_listening'
(2) add a mutex in open() to prevent race condition
v3 (chk): grab the reset lock to avoid race in autodump_open,
rename debugfs file to amdgpu_autodump,
provide autodump_read as well,
style and code cleanups
v4: add 'bool app_listening' to differentiate situations, so that
the node can be reopened; also, there is no need to wait for
completion when no app is waiting for a dump.
v5: change 'bool app_listening' to 'enum amdgpu_autodump_state'
add 'app_state_mutex' for race conditions:
(1)Only 1 user can open this file node
(2)wait_dump() can only take effect after poll() executed.
(3)eliminated the race condition between release() and
wait_dump()
v6: removed 'enum amdgpu_autodump_state' and 'app_state_mutex'
removed state checking in amdgpu_debugfs_wait_dump
Improve on top of version 3 so that the node can be reopened.
v7: move reinit_completion into open() so that only one user
can open it.
v8: remove complete_all() from amdgpu_debugfs_wait_dump().
Signed-off-by: Jiange Zhao <Jiange.Zhao@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
'exynos_dsi_parse_dt()' takes a reference to 'dsi->in_bridge_node'.
This must be released in the error handling path.
In order to do that, add an error handling path and move the
'exynos_dsi_parse_dt()' call from the beginning to the end of the probe
function to ease the error handling path.
This function only sets some variables which are used only in the
'transfer' function.
The call chain is:
.transfer
--> exynos_dsi_host_transfer
--> exynos_dsi_init
--> exynos_dsi_enable_clock (use burst_clk_rate and esc_clk_rate)
--> exynos_dsi_set_pll (use pll_clk_rate)
While at it, also handle cases where 'component_add()' fails.
This patch is similar to commit 70505c2ef9 ("drm/exynos: dsi: Remove bridge node reference in removal")
which fixed the issue in the remove function.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Runtime power management is essential for the Exynos Mixer driver
operation. It should be enabled before adding its DRM component, because
in some cases (when deferred probe takes place due to the IOMMU
availability) the DRM driver might be initialized directly from the
Mixer's component_add() call, what results in starting the driver
operation without enabling the runtime power management.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Maybe keep pointer which points to global const string data
in const type is better, make sure not change const data.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Internal pages array and scatter-list for them is not really needed for
anything. FBDev emulation can simply rely on the DMA-mapping framework
to create a proper kernel mapping for the buffer, while all other buffer
use cases don't really need that array at all.
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Explicitly check if the imported buffer has been mapped as contiguous in
the DMA address space, what is required by all Exynos DRM CRTC drivers.
While touching this, set buffer flags depending on the availability of
the IOMMU.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The ExynosDRM page fault handler is never used, drm_gem_mmap()
always calls exynos_drm_gem_mmap() function, which perform
complete mapping for the given virtual address-space area.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The function “platform_get_irq” can log an error already.
Thus omit redundant messages for the exception handling in the
calling functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
drm_helper_probe_add_cmdline_mode() prefers using a probed mode matching
a video= argument over calculating our own timings for the user specified
mode using CVT or GTF.
But userspace code which is auto-configuring the mode may want to know that
the user has specified that mode on the kernel commandline so that it can
pick that mode over the mode which is marked as DRM_MODE_TYPE_PREFERRED.
This commit sets the DRM_MODE_TYPE_USERDEF flag on the matching mode, just
as we would do on the user-specified mode when no matching probed mode is
found.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200221173313.510235-2-hdegoede@redhat.com
