With SDVO the pipe config pixel_multiplier only concerns itself with the
data on the SDVO bus. Any HDMI specific pixel repeat must be handled by
the SDVO device itself. To do that simply configure the SDVO pixel
replication factor appropriately. We already set up the infoframe PRB
values correctly via the infoframe helpers.
There is no cap we can check for this. The spec says that 1X,2X,4X are
mandatory, anything else is optional. 1X and 2X are all we need so
we should be able to assume they work.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108181242.13650-7-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The SDVO/HDMI port register limited color range bit can only be used
with TMDS encoding and not SDVO encoding, ie. to be used only when
using the port as a HDMI port as opposed to a SDVO port. The SDVO
spec does have a note that some GMCHs might allow that, but gen4
bspec vehemently disagrees. I suppose on ILK+ it might work since
the color range handling is on the CPU side rather than on the PCH
side, so there is no clear linkage between the TMDS vs. SDVO
encoding and color range. Alas, I have no hardware to test that
theory.
To implement limited color range support for SDVO->HDMI we need to
ask the SDVO device to do the range compression. Do so, but first
check if the device even supports the colorimetry selection.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108181242.13650-5-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The following backtrace is seen when running aspeed G5 kernels.
WARNING: CPU: 0 PID: 1 at drivers/gpu/drm/drm_fb_helper.c:2233 drm_fbdev_generic_setup+0x138/0x198
aspeed_gfx 1e6e6000.display: Device has not been registered.
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.8.0-rc3 #1
Hardware name: Generic DT based system
Backtrace:
[<8010d6d0>] (dump_backtrace) from [<8010d9b8>] (show_stack+0x20/0x24)
r7:00000009 r6:60000153 r5:00000000 r4:8119fa94
[<8010d998>] (show_stack) from [<80b8cb98>] (dump_stack+0xcc/0xec)
[<80b8cacc>] (dump_stack) from [<80123ef0>] (__warn+0xd8/0xfc)
r7:00000009 r6:80e62ed0 r5:00000000 r4:974c3ccc
[<80123e18>] (__warn) from [<80123f98>] (warn_slowpath_fmt+0x84/0xc4)
r9:00000009 r8:806a0140 r7:000008b9 r6:80e62ed0 r5:80e631f8 r4:974c2000
[<80123f18>] (warn_slowpath_fmt) from [<806a0140>] (drm_fbdev_generic_setup+0x138/0x198)
r9:00000001 r8:9758fc10 r7:9758fc00 r6:00000000 r5:00000020 r4:9768a000
[<806a0008>] (drm_fbdev_generic_setup) from [<806d4558>] (aspeed_gfx_probe+0x204/0x32c)
r7:9758fc00 r6:00000000 r5:00000000 r4:9768a000
[<806d4354>] (aspeed_gfx_probe) from [<806dfca0>] (platform_drv_probe+0x58/0xa8)
Since commit 1aed9509b2 ("drm/fb-helper: Remove return value from
drm_fbdev_generic_setup()"), drm_fbdev_generic_setup() must be called
after drm_dev_register() to avoid the warning. Do that.
Fixes: 1aed9509b2 ("drm/fb-helper: Remove return value from drm_fbdev_generic_setup()")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701001002.74997-1-linux@roeck-us.net
We removed retiring requests from the shrinker in order to decouple the
mutexes from reclaim in preparation for unravelling the struct_mutex.
The impact of not retiring is that we are much less agressive in making
global objects available for shrinking, as such objects remain pinned
until they are flushed by a heartbeat pulse following the last retired
request along their timeline. In order to ensure that pulse occurs in
time for memory reclamation, we should kick it from kswapd.
The catch is that we have added some flush_work() into the retirement
phase (to ensure that we reach a global idle in a timely manner), but
these flush_work() are not eligible (i.e do not belong to WQ_MEM_RELCAIM)
for use from inside kswapd. To avoid flushing those workqueues, we teach
the retirer not to do so unless we are actually waiting, and only do the
plain retire from inside the shrinker.
Note that for execlists, we already retire completed contexts as they
are scheduled out, so it should not be keeping global state
unnecessarily pinned. The legacy ringbuffer however...
References: 9e9539800d ("drm/i915: Remove waiting & retiring from shrinker paths")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200708173748.32734-1-chris@chris-wilson.co.uk
drm_gem_dumb_map_offset() now exists and does everything
vgem_gem_dump_map does and *ought* to do.
In particular, vgem_gem_dumb_map() was trying to reject mmapping an
imported dmabuf by checking the existence of obj->filp. Unfortunately,
we always allocated an obj->filp, even if unused for an imported dmabuf.
Instead, the drm_gem_dumb_map_offset(), since commit 90378e5891
("drm/gem: drm_gem_dumb_map_offset(): reject dma-buf"), uses the
obj->import_attach to reject such invalid mmaps.
This prevents vgem from allowing userspace mmapping the dumb handle and
attempting to incorrectly fault in remote pages belonging to another
device, where there may not even be a struct page.
v2: Use the default drm_gem_dumb_map_offset() callback
Fixes: af33a9190d ("drm/vgem: Enable dmabuf import interfaces")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.13+
Link: https://patchwork.freedesktop.org/patch/msgid/20200708154911.21236-1-chris@chris-wilson.co.uk
clang static analysis flags this error
drivers/gpu/drm/radeon/ci_dpm.c:5652:9: warning: Use of memory after it is freed [unix.Malloc]
kfree(rdev->pm.dpm.ps[i].ps_priv);
^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/radeon/ci_dpm.c:5654:2: warning: Attempt to free released memory [unix.Malloc]
kfree(rdev->pm.dpm.ps);
^~~~~~~~~~~~~~~~~~~~~~
problem is reported in ci_dpm_fini, with these code blocks.
for (i = 0; i < rdev->pm.dpm.num_ps; i++) {
kfree(rdev->pm.dpm.ps[i].ps_priv);
}
kfree(rdev->pm.dpm.ps);
The first free happens in ci_parse_power_table where it cleans up locally
on a failure. ci_dpm_fini also does a cleanup.
ret = ci_parse_power_table(rdev);
if (ret) {
ci_dpm_fini(rdev);
return ret;
}
So remove the cleanup in ci_parse_power_table and
move the num_ps calculation to inside the loop so ci_dpm_fini
will know how many array elements to free.
Fixes: cc8dbbb4f6 ("drm/radeon: add dpm support for CI dGPUs (v2)")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When I update the latest kernel, I see the following "____ptrval____" boot
messages.
[ 1.872600] radeon 0000:01:05.0: fence driver on ring 0 use gpu addr 0x0000000048000c00 and cpu addr 0x(____ptrval____)
[ 1.879095] radeon 0000:01:05.0: fence driver on ring 5 use gpu addr 0x0000000040056038 and cpu addr 0x(____ptrval____)
Both radeon_fence_driver_start_ring() and amdgpu_fence_driver_start_ring()
have the similar issue, there exists the following two methods to solve it:
(1) Use "%pK" instead of "%p" so that the CPU address can be printed when
the kptr_restrict sysctl is set to 1.
(2) Just completely drop the CPU address suggested by Christian, because
the CPU address was useful in the past, but isn't any more. We now have a
debugfs file to read the current fence values.
Since the CPU address is not much useful, just remove the debug info about
CPU address.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To support inbox1 in CW4 we need to actually program CW4 instead of
region 4 for newer firmware.
This is done correctly on DCN20/DCN21 but this code wasn't added to
DCN30.
[How]
Copy over the missing code. It doesn't need address translation since
DCN30 uses virtual addressing.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to abstract register distances between two continuous
context domains and invalidation engines. In different ip headers, these
distances may be differences.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
kfd_pasid.c isn't using the kfd2kgd interface any more. Remove redundant
code trying to look up a device for finding that interface.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Kent Russell <kent.russell@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This field is missing for dcn3 so add it from dcn20.
enc2_set_dynamic_metadata() trys to sets this and we get a
generic_reg warning since the mask is not defined.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
