Removing the beacon cache entry from a uwb_dev can cause an oops if the
bce is released before the call to uwb_notify().
Signed-off-by: Stefano Panella <stefano.panella@csr.com>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Fix a NULL pointer dereference that would occur if the video decoder tied to
the em28xx supports the VIDIOC_INT_RESET call (for example: the cx25840 driver)
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the built-in touchscreen controller in DA9034
(aka Micco), usually found on platforms with xscale processors.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag marking a device running must be set before the URBs for
recption are submitted or they may complete too early and fail to resubmit.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch bumps the release number of the driver.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch saves the MIER register contents before treating
interrupts, then restores them correcty at the end of the
interrupt routine.
Signed-off-by: Joe Chou <Joe.Chou@rdc.com.tw>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In each case, if the NULL test is necessary, then the dereference should be
moved below the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since the QPACE (Chromodynamics Parallel Computing on the
Cell Broadband Engine) platform doesn't use a iommu, doesn't
have PCI devices and a MPIC much lesser setup and
configurations are needed. So far all devices are detected
as OF device. A notifier function is used to set the dma_ops
for the of_platform bus. Further this patch splits the
PPC_CELL_NATIVE into PPC_CELL_COMMON which are parts that are
shared with the QPACE platform and the rest.
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Instead of the home-grown d_fnstart(), d_fnend() and d_printf() macros,
use dev_dbg() or remove the message entirely.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
The comment about a "Conditional on hca_type" was cut-and-pasted from
the mthca driver, and doesn't apply to mlx4 (since only one type of HCA
is handled by mlx4). So just delete it.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When using MSI-X mode, create a completion event queue for each CPU.
Report the number of completion EQs in a new struct mlx4_caps member,
num_comp_vectors, and extend the mlx4_cq_alloc() interface with a
vector parameter so that consumers can specify which completion EQ
should be used to report events for the CQ being created.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds sh_mobile_lcdcfb deferred io support for SYS panels.
The LCDC hardware block managed by the sh_mobile_lcdcfb driver supports
RGB or SYS panel configurations. SYS panels come with an external display
controller that is resposible for refreshing the actual LCD panel. RGB
panels are controlled directly by the LCDC and they need to be refreshed
by the LCDC hardware.
In the case of SYS panels we can save some power by configuring the LCDC
hardware block in one-shot mode. In this one-shot mode panel refresh is
managed by software. This works well together with deferred io since it
allows us to stop clocks for most of the time and only enable clocks when
we actually want to trigger an update. When there is no fbdev activity
the clocks are kept stopped which allows us to deep sleep.
The refresh rate in deferred io mode is set using platform data. The same
platform data can also be used to disable deferred io mode.
As with other deferred io frame buffers user space code should use fsync()
on the frame buffer device to trigger an update.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the deferred io code from only supporting vmalloc()ed frame
buffer memory to support both vmalloc()ed and physically contiguous
frame buffer memory.
The sh_mobile_lcdcfb hardware does not support scatter gather so
we need physically contiguous memory to back our frame buffer.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make sure the mmap callback is set to NULL in the deferred io
cleanup function. This way we can enable and disable deferred
io on the fly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If CONFIG_FB_DEFERRED_IO is set, but there are framebuffers
registered that does not make use of deferred io, then fsync()
on those framebuffers will result in a crash. Fix that.
This is needed for sh_mobile_lcdcfb since we always enable
deferred io at compile time but we may disable deferred io
for some types of hardware configurations.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Since the sh_mobile_lcdc hardware has the framebuffer(s) in system RAM,
use FB_SYS instead of FB_CFB. Also hook in read and write helpers.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sci_poll_put_char() happens to also be used by the serial console,
while sci_poll_get_char() is only used by CONFIG_CONSOLE_POLL. Add
another gnarly ifdef to shut up the compiler.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the SH-2A FPU based SH7201 processor subtype.
Signed-off-by: Peter Griffin <pgriffin@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7720 and 7721 has IP of Frame Buffer same as SH7760.
This driver can support these.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The setting of the color palette was wrong, fixed it.
And removed fb_setcmap, and added fb_setcolreg function.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
drivers/usb/gadget/m66592-udc.c: In function 'm66592_probe':
drivers/usb/gadget/m66592-udc.c:1672: warning: label 'clean_up2' defined but not used
drivers/usb/host/r8a66597-hcd.c: In function 'r8a66597_probe':
drivers/usb/host/r8a66597-hcd.c:2401: warning: label 'clean_up2' defined but not used
Added by commit 985fc7c81c7852f2e104c71cbe913ace683c9e6a ("sh: sh_mobile
usbf clock framework support").
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the lcdc driver and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the usb/r8a66597 driver and
adjust the cpu specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the usbf/m66592 driver and
adjust the cpu specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the sh_mobile ceu and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the sh_mobile keysc driver and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the sh_mobile i2c driver and
adjust the processor specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch cleans up the tg3 header file by removing the preprocessor
definitions for standard PCI configuration space registers. The driver
should be using the standard definitions when needed. The patch
continues by removing redundant PHY related definitions and reorganizes
some of the remaining entries.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the pci_bist and pci_hdr_type members from the
device structure and removes the code that references them. They are
not really used.
The patch rounds out the changes by moving the pci_cmd member to plug
a structure hole that would have been created. On 32-bit systems, this
movement removes a subsequent structure hole later in the structure. On
64-bit systems though, the movement merely consolidates two holes into
one larger hole.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch attempts to make the relationship between IPV6 checksum
offload and IPV6 LSO more obvious. The patch also toggles a bit
needed for IPV6 LSO on 5785 and 57780 devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first hunk of this patch inverts a flag that was accidentally
toggled as part of commit 0a459aac9d
("tg3: Allow WOL for phylib controlled Broadcom phys").
The second hunk of the patch removes the call to
device_may_wakeup() in the 5906 config detection path. At the
point of the call, the driver shouldn't be querying for WOL
capability. It should be detecting and setting it.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
