Some configurations need more than 30 seconds to respond to a FIP VLAN
request so increase the default to 60 seconds.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For target mode, task management command is queued to specific cpu base
on where the SCSI command is residing. This prevent race condition of
task management command getting ahead of regular scsi command.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Uses predefine inline function to access add_cdb_len field in ATIO.
- Return SS_RESIDUAL_UNDER status when sending BUSY
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a connection is established, the target core session may not be
created immediately. Current code will drop/terminate the command based
on the session state. This patch will return BUSY status for any
commands arriving on wire before the session is created.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move GPSC & GFPNID commands out of session management to reduce time lag
in reporting the session state to remote port. These commands are not
essential when it comes to maintaining the rport state. Delay sending
these commands after rport state is set to Online.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For each RSCN that triggers a rescan of the fabric, ADISC is used to
revalidate an existing session. If the RSCN is not affecting all
existing sessions, then driver should not send redundant ADISC for all
existing sessions.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes login_retry login for ADISC command.
when login_retry count reaches 0, further attempt to send ADISC command
is ignored by the code. Remove this redundant login_retry count check
from qla24xx_fcport_handle_login()
[mkp: fix typo]
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In ioctl exit path driver refers ioc_list to free memory associated with
diag buffers and event_log pointer used to save events by driver.
If ctl_exit() func is called after unregistering driver, then ioc_list will
be empty and hence driver will not be able to free the allocated memory
which in turn causes memory leak.
So call ctl_exit() function before unregistering mpt3sas driver.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1) Manufacturing Page 11 contains parameters to control internal
firmware behavior. Based on AddlFlags2 field FW/Driver behaviour can
be changed, (flag tm_custom_handling is used for this)
a) For PCIe device, protocol level reset should be used if flag
tm_custom_handling is 0. Since Abort Task Set, LUN reset and Target
reset will result in a protocol level reset. Drivers should issue
only one type of this reset, if that fails then it should escalate to
a controller reset (diag reset/OCR).
b) If the driver has control over the TM reset timeout value, then
driver should use the value exposed in PCIe Device Page 2 for pcie
device (field ControllerResetTO).
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added function _base_display_fwpkg_version, which sends FWUpload request
to pull FW package version from FW Image Header. Now driver prints FW
package version in addition to FW version if the PackageVersion is
valid.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function _scsih_add_device, for each device connected to an
enclosure, driver reads the enclosure page(To get details like enclosure
handle, enclosure logical ID, enclosure level etc.)
With this patch, instead of reading enclosure page everytime, driver
maintains a list for enclosure device(During enclosure add event,
enclosure device is added to the list and removed from the list on
delete events) and uses the enclosure page from the list.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Events were not processed during driver unload, hence unloading of
driver doesn't complete when drives are disconnected while unloading of
driver. So don't block events in ISR path, i,e., remove the flag
ioc->remove_host so that events are getting processed during driver
unload. Thus allowing driver unload to complete by processing drive
removal events during driver unload.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For 24 port HBA's events generated by IOC are more in certain cases and
the current circular buffer may be overwritten.Hence increased the event
log buffer to accommodate more events.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enhanced DMA allocation for Sense Buffer, if the allocation does not fit
within same 4GB.Introduced is_MSB_are_same function to check if allocted
buffer within 4GB range or not.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For every IO, memory of PAGE size is allocated for handling NVMe native
PRPS. And in addition to that for every IO (chains need per IO * chain
buffer size, e.g. 38 * 128byte) amount of memory is allocated for chain
buffers.
However, at any point of time; the IO request can be for NVMe target
device (where PRP's page is used for framing PRP's) or can be for SCSI
target device (where chain buffers are used for framing chain
SGE's). This patch modifies the driver to reuse same pre-allocated PRP
page buffers as a chain buffer for IO's targeted for SCSI target
devices. No need to allocate separate buffers for chain SGE's buffers.
Suppose if the number of chain buffers need for IO doesn't fit in the
PRP Page size then driver maintain's separate buffers for those extra
chain buffers that exceeds the PRP page size. For example consider PRP
page size as 4K and chain buffer size as 128 bytes, then number of chain
buffers that can fit in PRP page is 4096/128 => 32. if the number of
chain buffer need per IO exceeds 32; for example consider number of
chains need per IO is 36 then for remaining 4 chain buffer's driver
allocates them individual.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduces Chain lookup table/tracker and implements accessing chain
buffer using smid. Removed link list based access of chain buffer which
requires lock and allocated as many chains needed.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of allocating RDPQ array (This stores the address's of each RDPQ
pools) at run time, now it will be allocated once during driver load
time and same will be reused during host reset operation also (instead
of allocating & freeing this buffer on the fly during every host reset
operation) and then freed during driver unload.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds driver changes for supporting the Unified Fabric Port
(UFP). This is a new paritioning mode wherein MFW provides the set of
parameters to be used by the device such as traffic class, outer-vlan
tag value, priority type etc. Drivers receives this info via notifications
from mfw and configures the hardware accordingly.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can rely on the dma-mapping code to handle any DMA limits that is
bigger than the ISA DMA mask for us (either using an iommu or swiotlb),
so remove setting the block layer bounce limit for anything but the
unchecked_isa_dma case, or the bouncing for highmem pages.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Trivial fix to spelling mistake in module parameter description text
[mkp: applied by hand]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistake in module parameter description text
[mkp: applied by hand]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The sanity check on u->in_connection_align_insertion_frequency is being
performed twice and hence the first check can be removed since it is
redundant. Cleans up cppcheck warning:
drivers/scsi/ibmvscsi/ibmvscsi.c:1711: (warning) Identical inner 'if'
condition is always true.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
commit b60710ec7d ("scsi: aacraid: enable sending of TMFs from
aac_hba_send()") allows aac_hba_send() to send scsi commands, and TMF
requests, but the existing code only updates the iu_type for scsi
commands. For TMF requests we are sending an unknown iu_type to
firmware, which causes a fault.
Include iu_type prior to determining the validity of the command
Reported-by: Noah Misner <nmisner@us.ibm.com>
Fixes: b60710ec7d ("aacraid: enable sending of TMFs from aac_hba_send()")
Fixes: 423400e64d ("aacraid: Include HBA direct interface")
Tested-by: Noah Misner <nmisner@us.ibm.com>
cc: stable@vger.kernel.org
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The vmw_pvscsi driver returns DID_ABORT for commands aborted internally
by the adapter, leading to the filesystem going read-only. Change the
result to DID_BUS_BUSY, causing the kernel to retry the command.
Signed-off-by: Jim Gill <jgill@vmware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All three instance of ->smp_handler deal with highmem backed requests
just fine.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
do_gettimeofday() is deprecated since it will stop working in 2038 on
32-bit platforms, leading to incorrect times passed to the firmware.
On 64-bit platforms the current code appears to be fine, as the
calculation passes an 8-bit century number into the firmware that can
represent times long in the future (possibly until 25599).
Using ktime_get_real_seconds() to get a 64-bit seconds value and
time64_to_tm() to convert it into the firmware format greatly simplifies
the ips timekeeping code, makes 32-bit and 64-bit behave the same way
here, and gets us closer to removing the deprecated interfaces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
do_gettimeofday() is deprecated because of the y2038 overflow. Here, we
use the result to pass into a 32-bit field in the firmware, which still
risks an overflow, but if the firmware is written to expect unsigned
values, it can at least last until y2106, and there is not much we can
do about it.
This changes do_gettimeofday() to ktime_get_real_seconds(), which at
least simplifies the code a bit, and avoids the deprecated
interface. I'm adding a comment about the overflow to document what
happens.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the case when the phy_mask is bitwise anded with the phy_index bit is
zero the continue statement currently jumps to the next iteration of the
while loop and phy_index is never actually incremented, potentially
causing an infinite loop if phy_index is less than SCI_MAX_PHS. Fix this
by turning the while loop into a for loop.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
new_tape_buffer() is never called in atomic context. new_tape_buffer()
is only called by st_probe(), which is only set as ".probe" in struct
scsi_driver.
Despite never getting called from atomic context, new_tape_buffer()
calls kzalloc() with GFP_ATOMIC, which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL, which
can sleep and improve the possibility of sucessful allocation.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
st_probe() is never called in atomic context. st_probe() is only set as
".probe" in struct scsi_driver.
Despite never getting called from atomic context, st_probe() calls
kzalloc() with GFP_ATOMIC, which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL, which
can sleep and improve the possibility of sucessful allocation.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On Fujitsu ETERNUS systems, sense code ABORTED COMMAND with ASC/Q C1/01
is used to indicate temporary condition where the storage-internal path
to a target is switched from one controller to another. SCSI commands
that return with this error code must be retried unconditionally
(i.e. without the "maybe_retry" logic in scsi_decide_disposition);
otherwise dm-multipath might initiate a failover from a healthy path
e.g. for REQ_FAILFAST_DEV commands.
Introduce a new blist flag for this case.
[mkp: applied by hand]
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
EMC Symmetrix returns 'internal target error' for a variety of
conditions, most of which will be transient. So we should always retry
it, even with failfast set. Otherwise we'd get spurious path flaps with
multipath.
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
