We augment the GPIO regulator to get the *enable* regulator
GPIO line (not the other lines) using a descriptor rather than
a global number.
We then pass this into the regulator core which has been
prepared to hande enable descriptors in a separate patch.
Switch over the two boardfiles using this facility and clean
up so we only pass descriptors around.
Cc: Philipp Zabel <philipp.zabel@gmail.com> # HX4700/Magician maintainer
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As we augmented the regulator core to accept a GPIO descriptor instead
of a GPIO number, we can augment the fixed GPIO regulator to look up
and pass that descriptor directly from device tree or board GPIO
descriptor look up tables.
Some boards just auto-enumerate their fixed regulator platform devices
and I have assumed they get names like "fixed-regulator.0" but it's
pretty hard to guess this. I need some testing from board maintainers to
be sure. Other boards are straight forward, using just plain
"fixed-regulator" (ID -1) or "fixed-regulator.1" hammering down the
device ID.
The OMAP didn't have proper label names on its GPIO chips so I have fixed
this with a separate patch to the GPIO tree, see
commit 088413bc0b
"gpio: omap: Give unique labels to each GPIO bank/chip"
It seems the da9055 and da9211 has never got around to actually passing
any enable gpio into its platform data (not the in-tree code anyway) so we
can just decide to simply pass a descriptor instead.
The fixed GPIO-controlled regulator in mach-pxa/ezx.c was confusingly named
"*_dummy_supply_device" while it is a very real device backed by a GPIO
line. There is nothing dummy about it at all, so I renamed it with the
infix *_regulator_* as part of this patch set.
For the patch hunk hitting arch/blackfin I would say I do not expect
testing, review or ACKs anymore so if it works, it works.
The hunk hitting the x86 BCM43xx driver is especially tricky as the number
comes out of SFI which is a mystery to me. I definately need someone to
look at this. (Hi Andy.)
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Check the x86 BCM stuff
Cc: Alexander Shiyan <shc_work@mail.ru> # i.MX boards user
Cc: Haojian Zhuang <haojian.zhuang@gmail.com> # MMP2 maintainer
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> # OMAP1 maintainer
Cc: Tony Lindgren <tony@atomide.com> # OMAP1,2,3 maintainer
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> # EM-X270 maintainer
Cc: Robert Jarzmik <robert.jarzmik@free.fr> # EZX maintainer
Cc: Philipp Zabel <philipp.zabel@gmail.com> # Magician maintainer
Cc: Daniel Mack <zonque@gmail.com> # Raumfeld maintainer
Cc: Marc Zyngier <marc.zyngier@arm.com> # Zeus maintainer
Cc: Geert Uytterhoeven <geert+renesas@glider.be> # SuperH pinctrl/GPIO maintainer
Cc: Russell King <rmk+kernel@armlinux.org.uk> # SA1100
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This matches the implementation of the more commonly used unmap_single
routines and the sync_sg_for_cpu method which should provide equivalent
cache maintainance.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Greentime Hu <greentime@andestech.com>
Tested-by: Greentime Hu <greentime@andestech.com>
Make sure all other DMA methods call nds32_dma_sync_single_for_{device,cpu}
to perform cache maintaince, and remove the consisteny_sync helper that
implemented both with entirely separate code based off an argument.
Also make sure these helpers handled highmem properly, for which code
is copy and pasted from mips.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Greentime Hu <greentime@andestech.com>
Tested-by: Greentime Hu <greentime@andestech.com>
The kernel depends on macros like __BYTE_ORDER__,
__BIG_ENDIAN__ or __LITTLE_ENDIAN__.
OTOH, sparse doesn't know about the endianness of the kernel and
by default uses the same as the machine on which sparse was built.
Ensure that sparse can predefine the macros corresponding to
how the kernel was configured by adding -m{big,little}-endian
to CHECKFLAGS in the main Makefile (and so for all archs).
Also, remove the equivalent done in arch specific Makefiles.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Kconfig got text processing tools like we see in Make. Add Kconfig
helper macros to scripts/Kconfig.include like we collect Makefile
macros in scripts/Kbuild.include.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Ulf Magnusson <ulfalizer@gmail.com>
The kernel configuration phase is now tightly coupled with the compiler
in use. It will be nice to show the compiler information in Kconfig.
The compiler information will be displayed like this:
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- config
scripts/kconfig/conf --oldaskconfig Kconfig
*
* Linux/arm64 4.16.0-rc1 Kernel Configuration
*
*
* Compiler: aarch64-linux-gnu-gcc (Linaro GCC 7.2-2017.11) 7.2.1 20171011
*
*
* General setup
*
Compile also drivers which will not load (COMPILE_TEST) [N/y/?]
If you use GUI methods such as menuconfig, it will be displayed in the
top menu.
This is simply implemented by using the 'comment' statement. So, it
will be saved into the .config file as well.
This commit has a very important meaning. If the compiler is upgraded,
Kconfig must be re-run since different compilers have different sets
of supported options.
All referenced environments are written to include/config/auto.conf.cmd
so that any environment change triggers syncconfig, and prompt the user
to input new values if needed.
With this commit, something like follows will be added to
include/config/auto.conf.cmd
ifneq "$(CC_VERSION_TEXT)" "aarch64-linux-gnu-gcc (Linaro GCC 7.2-2017.11) 7.2.1 20171011"
include/config/auto.conf: FORCE
endif
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
To get access to environment variables, Kconfig needs to define a
symbol using "option env=" syntax. It is tedious to add a symbol entry
for each environment variable given that we need to define much more
such as 'CC', 'AS', 'srctree' etc. to evaluate the compiler capability
in Kconfig.
Adding '$' for symbol references is grammatically inconsistent.
Looking at the code, the symbols prefixed with 'S' are expanded by:
- conf_expand_value()
This is used to expand 'arch/$ARCH/defconfig' and 'defconfig_list'
- sym_expand_string_value()
This is used to expand strings in 'source' and 'mainmenu'
All of them are fixed values independent of user configuration. So,
they can be changed into the direct expansion instead of symbols.
This change makes the code much cleaner. The bounce symbols 'SRCARCH',
'ARCH', 'SUBARCH', 'KERNELVERSION' are gone.
sym_init() hard-coding 'UNAME_RELEASE' is also gone. 'UNAME_RELEASE'
should be replaced with an environment variable.
ARCH_DEFCONFIG is a normal symbol, so it should be simply referenced
without '$' prefix.
The new syntax is addicted by Make. The variable reference needs
parentheses, like $(FOO), but you can omit them for single-letter
variables, like $F. Yet, in Makefiles, people tend to use the
parenthetical form for consistency / clarification.
At this moment, only the environment variable is supported, but I will
extend the concept of 'variable' later on.
The variables are expanded in the lexer so we can simplify the token
handling on the parser side.
For example, the following code works.
[Example code]
config MY_TOOLCHAIN_LIST
string
default "My tools: CC=$(CC), AS=$(AS), CPP=$(CPP)"
[Result]
$ make -s alldefconfig && tail -n 1 .config
CONFIG_MY_TOOLCHAIN_LIST="My tools: CC=gcc, AS=as, CPP=gcc -E"
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Pull nds32 fixes from Greentime Hu:
"Bug fixes and build error fixes for nds32"
* tag 'nds32-for-linus-4.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/greentime/linux:
nds32: Fix compiler warning, Wstringop-overflow, in vdso.c
nds32: Disable local irq before calling cpu_dcache_wb_page in copy_user_highpage
nds32: Flush the cache of the page at vmaddr instead of kaddr in flush_anon_page
nds32: Correct flush_dcache_page function
nds32: Fix the unaligned access handler
nds32: Renaming the file for unaligned access
nds32: To fix a cache inconsistency issue by setting correct cacheability of NTC
nds32: To refine readability of INT_MASK_INITAIAL_VAL
nds32: Fix the virtual address may map too much range by tlbop issue.
nds32: Fix the allmodconfig build. To make sure CONFIG_CPU_LITTLE_ENDIAN is default y
nds32: Fix build failed because arch_trace_hardirqs_off is changed to trace_hardirqs_off.
nds32: Fix the unknown type u8 issue.
nds32: Fix the symbols undefined issue by exporting them.
nds32: Fix xfs_buf built failed by export invalidate_kernel_vmap_range and flush_kernel_vmap_range
nds32: Fix drivers/gpu/drm/udl/udl_fb.c building error by defining PAGE_SHARED
nds32: Fix building error of crypto/xor.c by adding xor.h
nds32: Fix building error when CONFIG_FREEZE is enabled.
nds32: lib: To use generic lib instead of libgcc to prevent the symbol undefined issue.
Instead of globally disabling > 32bit DMA using the arch_dma_supported
hook walk the PCI bus under the actually affected bridge and mark every
device with the dma_32bit_limit flag. This also gets rid of the
arch_dma_supported hook entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
This is something drivers should decide (modulo chipset quirks like
for VIA), which as far as I can tell is how things have been handled
for the last 15 years.
Note that we keep the usedac option for now, as it is used in the wild
to override the too generic VIA quirk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Limiting the dma mask to avoid PCI (pre-PCIe) DAC cycles while paying
the huge overhead of an IOMMU is rather pointless, and this seriously
gets in the way of dma mapping work.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
The toc field in the mod_arch_specific struct isn't actually used
anywhere, so remove it.
Also the ftrace-specific fields are now common between 32-bit and
64-bit, so simplify the struct definition a bit by moving them out of
the __powerpc64__ #ifdef.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Init all present cpus for deep states instead of "all possible" cpus.
Init fails if a possible cpu is guarded. Resulting in making only
non-deep states available for cpuidle/hotplug.
Stewart says, this means that for single threaded workloads, if you
guard out a CPU core you'll not get WoF (Workload Optimised
Frequency), which means that performance goes down when you wouldn't
expect it to.
Fixes: 77b54e9f21 ("powernv/powerpc: Add winkle support for offline cpus")
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The ColdFire PCI configuration space access functions swap addressing
regions to do their work. Just letting the read/write cycles exit
the CPU core (via the ColdFire "nop" instruction) is not enough to
guarantee that the address region remapping has actually completed.
Insert a read back of the mapping register to be absolutely sure
that the remapping has completed.
This fixes an occasional boot hang during the ColdFire PCI initialization
phase.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
A lot of the ColdFire internal peripherals (clocks, timers, interrupt
controllers, etc) are addressed using constants. The only problem with
that is they are not type clean when used with __raw_read/__raw_write
and read/write - they should be of type "void __iomem". This isn't
a problem currently because the IO access functions are local macros.
To switch to using the asm-generic implementations of these we need to
clean up the types. Otherwise you get warnings like this:
In file included from ./arch/m68k/include/asm/mcfsim.h:24:0,
from arch/m68k/coldfire/intc-simr.c:20:
arch/m68k/coldfire/intc-simr.c: In function ‘init_IRQ’:
./arch/m68k/include/asm/m520xsim.h:40:29: warning: passing argument 2 of ‘__raw_writeb’ makes pointer from integer without a cast [-Wint-conversion]
#define MCFINTC0_SIMR (MCFICM_INTC0 + MCFINTC_SIMR)
^
arch/m68k/coldfire/intc-simr.c:182:21: note: in expansion of macro ‘MCFINTC0_SIMR’
__raw_writeb(0xff, MCFINTC0_SIMR);
^
In file included from ./arch/m68k/include/asm/io_no.h:120:0,
from ./arch/m68k/include/asm/io.h:3,
from ./include/linux/io.h:25,
from ./include/linux/irq.h:25,
from ./include/asm-generic/hardirq.h:13,
from ./arch/m68k/include/asm/hardirq.h:25,
from ./include/linux/hardirq.h:9,
from ./include/linux/interrupt.h:13,
from arch/m68k/coldfire/intc-simr.c:16:
./include/asm-generic/io.h:71:22: note: expected ‘volatile void *’ but argument is of type ‘unsigned int’
#define __raw_writeb __raw_writeb
^
./include/asm-generic/io.h:72:20: note: in expansion of macro ‘__raw_writeb’
static inline void __raw_writeb(u8 value, volatile void __iomem *addr)
^
To start this clean up process introduce a macro, iomem(), that converts
a constant address to the correct "void __iomem *" type.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Up to now we have only had support for the PCI bus when running the
ColdFire CPU family with the MMU enabled. The only reason for this was
the incomplete state of the IO remapping and access functions when
running with the MMU disabled.
Recent fixes and improvements to the ColdFire IO access code means we
can now support the PCI bus when running non-MMU enabled as well.
So modify the configuration support to allow it to be selected no matter
what choice of MMU mode is used.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
The ColdFire SoC internal peripherals are mapped into virtual address
space using the ACR registers of the cache control unit. This means we
are using a 1:1 physical:virtual mapping for them that does not rely on
page table mappings. We can quickly determine if we are accessing an
internal peripheral device given the physical or vitrual address using
the same range check.
The implications of this mapping is that an ioremap should return the
physical address as the virtual mapping __iomem cookie as well. So fix
ioremap() to deal with this on ColdFire. Of course you need to take
care of this in the iounmap() path as well.
Reported-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
We need to treat built-in peripherals and bus based address ranges
differently. Local built-in peripherals (and the ColdFire SoC parts
have quite a lot of them) are always native endian - which is big
endian on m68k/ColdFire. Bus based address ranges, like the PCI bus,
are accessed little endian - so we need to byte swap those.
So implement readw/writew and readl/writel functions to deal with
memory mapped accesses correctly based on the address range being
accessed.
This fixes readw/writew and readl/writel so that they can be used in
drivers for native SoC hardware modules (many of which are shared with
other architectures (ARM in Freescale SoC parts for example). And also
drivers for PCI devices.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Some ColdFire platforms do have real PCI buses, so we should not be
re-defining or otherwise mangling the IO access functions for them.
So when CONFIG_PCI is true use the real io.h support.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
All the ColdFire IO access support code has been moved to io_no.h.
This means that all ColdFire support is at least now consistent no
matter whether the MMU is enabled or not for them.
Now that io_mm.h has reverted to only support the traditional m68k MMU
enabled processors we can remove the ColdFire specific definitions.
We can also remove the old ColdFire PCI bus IO access functions.
The new io_no.h uses asm-generic/io.h to provide all the basic support.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Use the io_no.h IO access support for all ColdFire systems, no matter
whether configured with MMU enabled or disabled. Previously there was
subtle differences in IO access functions used in both cases, and these
resulted in broken behavior for some drivers.
As observed and reported by Angelo when using MMU enabled systems the
read/write family of functions was using little endian access, while the
non-MMU enabled systems were using native endian. This results in drivers
that are shared across Freescale processors (for some of the common
internal SoC peripherals) not working - since they are wired up for native
endian access.
This problem brings to light issues with PCI bus access and local
peripheral access - but these are not addressed with this fix.
Reported-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Ultimately we want the ColdFire IO access support to be consisent no matter
whether it is configured with MMU enabled or disabled. To acheive that we
need to get all the ColdFire IO access support code together in one place,
in this case io_no.h. The last big piece not in io_no.h is the PCI bus
support functions.
Define the IO mapping addresses required to use the asm-generic IO
access functions. They can provide everything we need - no need for us
to duplicate or have local in/out or read/write access functions.
Note that this support is not active yet, since we haven't done the
full switch over to using the asm-generic functions yet. And also note
that we do not yet remove the old PCI functions from io_mm.h yet.
Consolodating all this IO access support in a single place will make
it easier in the future to enable PCI bus support for non-MMU enabled
ColdFire (which we currently cannot do).
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Create a new header file, kmap.h, that groups all the definitions and
functions associated with the io mapping and remapping.
Currently the functions are spread across raw_io.h and io_mm.h. And in
the future we will want to use these in io_no.h as well. So it makes
sense to move them all together into a single header file.
It is named after the arch/m68k/mm/kmap.c file that actually implements
many of the exported functions.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Tested-by: Angelo Dureghello <angelo@sysam.it>
The primary and fundamental access macros are really the __raw versions.
So make them the actual implementation for access, and not the read/write
access macros. The read/write macros and functions are built on top of
the raw access (with byte swapping or other actions as required).
This in itself causes no functional change right now. But it will make it
easier to fix and resolve problems with PCI bus access in the future.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
There is nothing really special about the non-MMU m68k IO access functions.
So we can easily switch to using the asm-generic/io.h functions.
The only thing we do need to handle is that historically the m68k IO access
functions for readw/readl/writew/writel use native CPU endian ordering. So
for us on m68k/ColdFire that means they are big-endian. Leave the existing
set of _raw_read/__raw_write and read/write macros in place to deal with
them. (They are ripe for later cleanup, but that is for another patch).
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
The non-MMU and ColdFire IO access functions will be moving to using the
asm-generic/io.h in the near future. To make that possible we need define
guards around the m68k specific virt_to_phys() and phys_to_virt()
functions.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Move a copy of the definitions of the *_relaxed() macros into io_no.h
and io_mm.h. This precedes a change to the io_no.h file to use
asm-generic/io.h. They will be removed from io_no.h at that point.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Renesas ARM Based SoC Updates for v4.18
* SoC
- Change platform dependency to ARCH_RENESAS
This will allow to drop ARCH_SHMOBILE on ARM and ARM64 in the near
future.
- Add the to Kconfig RZ/N1D (r9a06g032) SoC
- Identify R-Car E3 (r8a77990) SoC
- Identify and add minimal support for RZ/G1C (r8a77470) SoC
* R-Car SYSC
- Add support for R-Car E3 (r8a77990) SoC
- Remove unused inclusion of <linux/sys_soc.h>,
- Make r8a77995_areas[] const.
* R-Car Reset
- Add support for R-Car E3 (r8a77990) SoC
* Debug-LL
- Add support for RZ/G1C (r8a77470) SoC
* tag 'renesas-soc-for-v4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
soc: renesas: r8a77990-sysc: Add workaround for 3DG-{A,B}
soc: renesas: rcar-sysc: Add support for R-Car E3 power areas
arm: shmobile: Add the RZ/N1D (R9A06G032) to the shmobile Kconfig
arm: shmobile: Change platform dependency to ARCH_RENESAS
soc: renesas: r8a77995-sysc: Cleanups
soc: renesas: rcar-rst: Add support for R-Car E3
soc: renesas: Add r8a77990 SYSC PM Domain Binding Definitions
soc: renesas: identify R-Car E3
ARM: debug-ll: Add support for r8a77470
ARM: shmobile: Add the RZ/N1 arch to the shmobile Kconfig
ARM: shmobile: r8a77470: basic SoC support
soc: renesas: rcar-sysc: Add r8a77470 support
soc: renesas: rcar-rst: Add support for RZ/G1C
soc: renesas: Identify RZ/G1C
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM SoC fixes from Olof Johansson:
"A few more fixes for v4.17:
- a fix for a crash in scm_call_atomic on qcom platforms
- display fix for Allwinner A10
- a fix that re-enables ethernet on Allwinner H3 (C.H.I.P et al)
- a fix for eMMC corruption on hikey
- i2c-gpio descriptor tables for ixp4xx
... plus a small typo fix"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: Fix i2c-gpio GPIO descriptor tables
arm64: dts: hikey: Fix eMMC corruption regression
firmware: qcom: scm: Fix crash in qcom_scm_call_atomic1()
ARM: sun8i: v3s: fix spelling mistake: "disbaled" -> "disabled"
ARM: dts: sun4i: Fix incorrect clocks for displays
ARM: dts: sun8i: h3: Re-enable EMAC on Orange Pi One
Pull x86 store buffer fixes from Thomas Gleixner:
"Two fixes for the SSBD mitigation code:
- expose SSBD properly to guests. This got broken when the CPU
feature flags got reshuffled.
- simplify the CPU detection logic to avoid duplicate entries in the
tables"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/speculation: Simplify the CPU bug detection logic
KVM/VMX: Expose SSBD properly to guests
Renesas ARM Based SoC Defconfig Updates for v4.18
* Enable in shmobile and multi_v7 defconfigs to give wider test coverage:
- Recently mainlined support for RZ/G1C (r8a77470) SoC
- Renesas Watchdog (RENESAS_WDT) which is used on
R-Car Gen2 and RZ/G1 platforms.
* Disable in shmobile and multi_v7 defconfigs to avoid unecessary bloat:
FB_SH_MOBILE_MERAM the last user of which was removed in v4.1 by
a521422ea4 ("ARM: shmobile: mackerel: Remove Legacy C board
code").
* tag 'renesas-defconfig-for-v4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: multi_v7_defconfig: Enable RENESAS_WDT
ARM: shmobile: defconfig: Enable RENESAS_WDT_GEN
ARM: multi_v7_defconfig: Disable CONFIG_FB_SH_MOBILE_MERAM
ARM: shmobile: defconfig: Disable CONFIG_FB_SH_MOBILE_MERAM
ARM: multi_v7_defconfig: Enable r8a77470 SoC
ARM: shmobile: defconfig: Enable r8a77470 SoC
Signed-off-by: Olof Johansson <olof@lixom.net>
Qualcomm ARM64 Based defconfig Updates for v4.18
* Enable UFS and PCIe for Qualcomm msm8996/db820c
* tag 'qcom-arm64-defconfig-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: defconfig: Enable PCIe on msm8996 and db820c
arm64: defconfig: Enable UFS on msm8996
Signed-off-by: Olof Johansson <olof@lixom.net>
AT91 DT for 4.18:
- small DT improvements without functional changes
* tag 'at91-ab-4.18-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91-sama5d2_xplained: Use IRQ_TYPE specifier
ARM: dts: at91: sama5d4ek: use canonical compatible for touchscreen
Signed-off-by: Olof Johansson <olof@lixom.net>
I used bad names in my clumsiness when rewriting many board
files to use GPIO descriptors instead of platform data. A few
had the platform_device ID set to -1 which would indeed give
the device name "i2c-gpio".
But several had it set to >=0 which gives the names
"i2c-gpio.0", "i2c-gpio.1" ...
Fix the offending instances in the ARM tree. Sorry for the
mess.
Fixes: b2e6355559 ("i2c: gpio: Convert to use descriptors")
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Reported-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull KVM fixes from Radim Krčmář:
"PPC:
- Close a hole which could possibly lead to the host timebase getting
out of sync.
- Three fixes relating to PTEs and TLB entries for radix guests.
- Fix a bug which could lead to an interrupt never getting delivered
to the guest, if it is pending for a guest vCPU when the vCPU gets
offlined.
s390:
- Fix false negatives in VSIE validity check (Cc stable)
x86:
- Fix time drift of VMX preemption timer when a guest uses LAPIC
timer in periodic mode (Cc stable)
- Unconditionally expose CPUID.IA32_ARCH_CAPABILITIES to allow
migration from hosts that don't need retpoline mitigation (Cc
stable)
- Fix guest crashes on reboot by properly coupling CR4.OSXSAVE and
CPUID.OSXSAVE (Cc stable)
- Report correct RIP after Hyper-V hypercall #UD (introduced in
-rc6)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: fix #UD address of failed Hyper-V hypercalls
kvm: x86: IA32_ARCH_CAPABILITIES is always supported
KVM: x86: Update cpuid properly when CR4.OSXAVE or CR4.PKE is changed
x86/kvm: fix LAPIC timer drift when guest uses periodic mode
KVM: s390: vsie: fix < 8k check for the itdba
KVM: PPC: Book 3S HV: Do ptesync in radix guest exit path
KVM: PPC: Book3S HV: XIVE: Resend re-routed interrupts on CPU priority change
KVM: PPC: Book3S HV: Make radix clear pte when unmapping
KVM: PPC: Book3S HV: Make radix use correct tlbie sequence in kvmppc_radix_tlbie_page
KVM: PPC: Book3S HV: Snapshot timebase offset on guest entry
This patch is a partial revert of
commit abd7d0972a ("arm64: dts: hikey: Enable HS200 mode on eMMC")
which has been causing eMMC corruption on my HiKey board.
Symptoms usually looked like:
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
...
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc0: new HS200 MMC card at address 0001
...
dwmmc_k3 f723d000.dwmmc0: Unexpected command timeout, state 3
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
print_req_error: I/O error, dev mmcblk0, sector 8810504
Aborting journal on device mmcblk0p10-8.
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
EXT4-fs error (device mmcblk0p10): ext4_journal_check_start:61: Detected aborted journal
EXT4-fs (mmcblk0p10): Remounting filesystem read-only
And quite often this would result in a disk that wouldn't properly
boot even with older kernels.
It seems the max-frequency property added by the above patch is
causing the problem, so remove it.
Cc: Ryan Grachek <ryan@edited.us>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: Leo Yan <leo.yan@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Wei Xu <xuwei04@gmail.com>
We need a new capability to indicate support for the newly added
HvFlushVirtualAddress{List,Space}{,Ex} hypercalls. Upon seeing this
capability, userspace is supposed to announce PV TLB flush features
by setting the appropriate CPUID bits (if needed).
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Implement HvFlushVirtualAddress{List,Space} hypercalls in a simplistic way:
do full TLB flush with KVM_REQ_TLB_FLUSH and kick vCPUs which are currently
IN_GUEST_MODE.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Prepare to support TLB flush hypercalls, some of which are REP hypercalls.
Also, return HV_STATUS_INVALID_HYPERCALL_INPUT as it seems more
appropriate.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
