From Skylake onwards, the platform controller hub (Sunrisepoint PCH) does
not support legacy DMA operations to IO ports 81h-83h, 87h, 89h-8Bh, 8Fh.
Currently this driver registers as syscore ops and its resume function is
called on every resume from S3. On Skylake and Kabylake, this causes a
resume delay of around 100ms due to port IO operations, which is a problem.
This change allows to load the driver only when the platform bios
explicitly supports such devices or has a cut-off date earlier than 2017
due to the following reasons:
- The platforms released before year 2017 have support for the 8237.
(except Sunrisepoint PCH e.g. Skylake)
- Some of the BIOS that were released for platforms (Skylake, Kabylake)
during 2016-17 are buggy. These BIOS do not set/unset the
ACPI_FADT_LEGACY_DEVICES field in FADT table properly based on the
presence or absence of the DMA device.
Very recently, open source system firmware like coreboot started unsetting
ACPI_FADT_LEGACY_DEVICES field in FADT table if the 8237 DMA device is not
present on the PCH.
Please refer to chapter 21 of 6th Generation Intel® Core™ Processor
Platform Controller Hub Family: BIOS Specification.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: rjw@rjwysocki.net
Cc: hpa@zytor.com
Cc: Alan Cox <alan@linux.intel.com>
Link: https://lkml.kernel.org/r/1522336015-22994-1-git-send-email-anshuman.gupta@intel.com
Make kernel print the correct number of TLB entries on Intel Xeon Phi 7210
(and others)
Before:
[ 0.320005] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
After:
[ 0.320005] Last level dTLB entries: 4KB 256, 2MB 128, 4MB 128, 1GB 16
The entries do exist in the official Intel SMD but the type column there is
incorrect (states "Cache" where it should read "TLB"), but the entries for
the values 0x6B, 0x6C and 0x6D are correctly described as 'Data TLB'.
Signed-off-by: Jacek Tomaka <jacek.tomaka@poczta.fm>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20180423161425.24366-1-jacekt@dugeo.com
The code used to iterate byte-by-byte over the bytes around RIP and that
is expensive: disabling pagefaults around it, copy_from_user, etc...
Make it read the whole buffer of OPCODE_BUFSIZE size in one go. Use a
statically allocated 64 bytes buffer so that concurrent show_opcodes()
do not interleave in the output even though in the majority of the cases
it's serialized via die_lock. Except the #PF path which doesn't...
Also, do the PAGE_OFFSET check outside of the function because latter
will be reused in other context.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Link: https://lkml.kernel.org/r/20180417161124.5294-5-bp@alien8.de
Recent AMD systems support using MWAIT for C1 state. However, MWAIT will
not allow deeper cstates than C1 on current systems.
play_dead() expects to use the deepest state available. The deepest state
available on AMD systems is reached through SystemIO or HALT. If MWAIT is
available, it is preferred over the other methods, so the CPU never reaches
the deepest possible state.
Don't try to use MWAIT to play_dead() on AMD systems. Instead, use CPUIDLE
to enter the deepest state advertised by firmware. If CPUIDLE is not
available then fallback to HALT.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Cc: Yazen Ghannam <Yazen.Ghannam@amd.com>
Link: https://lkml.kernel.org/r/20180403140228.58540-1-Yazen.Ghannam@amd.com
Both powerpc and alpha have cases where they wronly set si_code to 0
in combination with SIGTRAP and don't mean SI_USER.
About half the time this is because the architecture can not report
accurately what kind of trap exception triggered the trap exception.
The other half the time it looks like no one has bothered to
figure out an appropriate si_code.
For the cases where the architecture does not have enough information
or is too lazy to figure out exactly what kind of trap exception
it is define TRAP_UNK.
Cc: linux-api@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-alpha@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Call clear_siginfo to ensure every stack allocated siginfo is properly
initialized before being passed to the signal sending functions.
Note: It is not safe to depend on C initializers to initialize struct
siginfo on the stack because C is allowed to skip holes when
initializing a structure.
The initialization of struct siginfo in tracehook_report_syscall_exit
was moved from the helper user_single_step_siginfo into
tracehook_report_syscall_exit itself, to make it clear that the local
variable siginfo gets fully initialized.
In a few cases the scope of struct siginfo has been reduced to make it
clear that siginfo siginfo is not used on other paths in the function
in which it is declared.
Instances of using memset to initialize siginfo have been replaced
with calls clear_siginfo for clarity.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Vitezslav reported a case where the
"Timeout during microcode update!"
panic would hit. After a deeper look, it turned out that his .config had
CONFIG_HOTPLUG_CPU disabled which practically made save_mc_for_early() a
no-op.
When that happened, the discovered microcode patch wasn't saved into the
cache and the late loading path wouldn't find any.
This, then, lead to early exit from __reload_late() and thus CPUs waiting
until the timeout is reached, leading to the panic.
In hindsight, that function should have been written so it does not return
before the post-synchronization. Oh well, I know better now...
Fixes: bb8c13d61a ("x86/microcode: Fix CPU synchronization routine")
Reported-by: Vitezslav Samel <vitezslav@samel.cz>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Vitezslav Samel <vitezslav@samel.cz>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20180418081140.GA2439@pc11.op.pod.cz
Link: https://lkml.kernel.org/r/20180421081930.15741-2-bp@alien8.de
Pull x86 fixes from Thomas Gleixner:
"A small set of fixes for x86:
- Prevent X2APIC ID 0xFFFFFFFF from being treated as valid, which
causes the possible CPU count to be wrong.
- Prevent 32bit truncation in calc_hpet_ref() which causes the TSC
calibration to fail
- Fix the page table setup for temporary text mappings in the resume
code which causes resume failures
- Make the page table dump code handle HIGHPTE correctly instead of
oopsing
- Support for topologies where NUMA nodes share an LLC to prevent a
invalid topology warning and further malfunction on such systems.
- Remove the now unused pci-nommu code
- Remove stale function declarations"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/power/64: Fix page-table setup for temporary text mapping
x86/mm: Prevent kernel Oops in PTDUMP code with HIGHPTE=y
x86,sched: Allow topologies where NUMA nodes share an LLC
x86/processor: Remove two unused function declarations
x86/acpi: Prevent X2APIC id 0xffffffff from being accounted
x86/tsc: Prevent 32bit truncation in calc_hpet_ref()
x86: Remove pci-nommu.c
Chun-Yi reported a kernel warning message below:
WARNING: CPU: 0 PID: 0 at ../mm/early_ioremap.c:182 early_iounmap+0x4f/0x12c()
early_iounmap(ffffffffff200180, 00000118) [0] size not consistent 00000120
The problem is x86 kexec_file_load adds extra alignment to the efi
memmap: in bzImage64_load():
efi_map_sz = efi_get_runtime_map_size();
efi_map_sz = ALIGN(efi_map_sz, 16);
And __efi_memmap_init maps with the size including the alignment bytes
but efi_memmap_unmap use nr_maps * desc_size which does not include the
extra bytes.
The alignment in kexec code is only needed for the kexec buffer internal
use Actually kexec should pass exact size of the efi memmap to 2nd
kernel.
Link: http://lkml.kernel.org/r/20180417083600.GA1972@dhcp-128-65.nay.redhat.com
Signed-off-by: Dave Young <dyoung@redhat.com>
Reported-by: joeyli <jlee@suse.com>
Tested-by: Randy Wright <rwright@hpe.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull y2038 timekeeping syscall changes from Arnd Bergmann:
This is the first set of system call entry point changes to enable 32-bit
architectures to have variants on both 32-bit and 64-bit time_t. Typically
these system calls take a 'struct timespec' argument, but that structure
is defined in user space by the C library and its layout will change.
The kernel already supports handling the 32-bit time_t on 64-bit
architectures through the CONFIG_COMPAT mechanism. As there are a total
of 51 system calls suffering from this problem, reusing that mechanism
on 32-bit architectures.
We already have patches for most of the remaining system calls, but this
set contains most of the complexity and is best tested. There was one
last-minute regression that prevented it from going into 4.17, but that
is fixed now.
More details from Deepa's patch series description:
Big picture is as per the lwn article:
https://lwn.net/Articles/643234/ [2]
The series is directed at converting posix clock syscalls:
clock_gettime, clock_settime, clock_getres and clock_nanosleep
to use a new data structure __kernel_timespec at syscall boundaries.
__kernel_timespec maintains 64 bit time_t across all execution modes.
vdso will be handled as part of each architecture when they enable
support for 64 bit time_t.
The compat syscalls are repurposed to provide backward compatibility
by using them as native syscalls as well for 32 bit architectures.
They will continue to use timespec at syscall boundaries.
CONFIG_64_BIT_TIME controls whether the syscalls use __kernel_timespec
or timespec at syscall boundaries.
The series does the following:
1. Enable compat syscalls on 32 bit architectures.
2. Add a new __kernel_timespec type to be used as the data structure
for all the new syscalls.
3. Add new config CONFIG_64BIT_TIME(intead of the CONFIG_COMPAT_TIME in
[1] and [2] to switch to new definition of __kernel_timespec. It is
the same as struct timespec otherwise.
4. Add new CONFIG_32BIT_TIME to conditionally compile compat syscalls.
Intel's Skylake Server CPUs have a different LLC topology than previous
generations. When in Sub-NUMA-Clustering (SNC) mode, the package is divided
into two "slices", each containing half the cores, half the LLC, and one
memory controller and each slice is enumerated to Linux as a NUMA
node. This is similar to how the cores and LLC were arranged for the
Cluster-On-Die (CoD) feature.
CoD allowed the same cache line to be present in each half of the LLC.
But, with SNC, each line is only ever present in *one* slice. This means
that the portion of the LLC *available* to a CPU depends on the data being
accessed:
Remote socket: entire package LLC is shared
Local socket->local slice: data goes into local slice LLC
Local socket->remote slice: data goes into remote-slice LLC. Slightly
higher latency than local slice LLC.
The biggest implication from this is that a process accessing all
NUMA-local memory only sees half the LLC capacity.
The CPU describes its cache hierarchy with the CPUID instruction. One of
the CPUID leaves enumerates the "logical processors sharing this
cache". This information is used for scheduling decisions so that tasks
move more freely between CPUs sharing the cache.
But, the CPUID for the SNC configuration discussed above enumerates the LLC
as being shared by the entire package. This is not 100% precise because the
entire cache is not usable by all accesses. But, it *is* the way the
hardware enumerates itself, and this is not likely to change.
The userspace visible impact of all the above is that the sysfs info
reports the entire LLC as being available to the entire package. As noted
above, this is not true for local socket accesses. This patch does not
correct the sysfs info. It is the same, pre and post patch.
The current code emits the following warning:
sched: CPU #3's llc-sibling CPU #0 is not on the same node! [node: 1 != 0]. Ignoring dependency.
The warning is coming from the topology_sane() check in smpboot.c because
the topology is not matching the expectations of the model for obvious
reasons.
To fix this, add a vendor and model specific check to never call
topology_sane() for these systems. Also, just like "Cluster-on-Die" disable
the "coregroup" sched_domain_topology_level and use NUMA information from
the SRAT alone.
This is OK at least on the hardware we are immediately concerned about
because the LLC sharing happens at both the slice and at the package level,
which are also NUMA boundaries.
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: brice.goglin@gmail.com
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: "H. Peter Anvin" <hpa@linux.intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Link: https://lkml.kernel.org/r/20180407002130.GA18984@alison-desk.jf.intel.com
The TSC calibration code uses HPET as reference. The conversion normalizes
the delta of two HPET timestamps:
hpetref = ((tshpet1 - tshpet2) * HPET_PERIOD) / 1e6
and then divides the normalized delta of the corresponding TSC timestamps
by the result to calulate the TSC frequency.
tscfreq = ((tstsc1 - tstsc2 ) * 1e6) / hpetref
This uses do_div() which takes an u32 as the divisor, which worked so far
because the HPET frequency was low enough that 'hpetref' never exceeded
32bit.
On Skylake machines the HPET frequency increased so 'hpetref' can exceed
32bit. do_div() truncates the divisor, which causes the calibration to
fail.
Use div64_u64() to avoid the problem.
[ tglx: Fixes whitespace mangled patch and rewrote changelog ]
Signed-off-by: Xiaoming Gao <newtongao@tencent.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Cc: peterz@infradead.org
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/38894564-4fc9-b8ec-353f-de702839e44e@gmail.com
The |= operator will let us end up with an invalid PTE. Use
the correct &= instead.
[ The bug was also independently reported by Shuah Khan ]
Fixes: fb43d6cb91 ('x86/mm: Do not auto-massage page protections')
Acked-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 fixes from Thomas Gleixner:
"A set of fixes and updates for x86:
- Address a swiotlb regression which was caused by the recent DMA
rework and made driver fail because dma_direct_supported() returned
false
- Fix a signedness bug in the APIC ID validation which caused invalid
APIC IDs to be detected as valid thereby bloating the CPU possible
space.
- Fix inconsisten config dependcy/select magic for the MFD_CS5535
driver.
- Fix a corruption of the physical address space bits when encryption
has reduced the address space and late cpuinfo updates overwrite
the reduced bit information with the original value.
- Dominiks syscall rework which consolidates the architecture
specific syscall functions so all syscalls can be wrapped with the
same macros. This allows to switch x86/64 to struct pt_regs based
syscalls. Extend the clearing of user space controlled registers in
the entry patch to the lower registers"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Fix signedness bug in APIC ID validity checks
x86/cpu: Prevent cpuinfo_x86::x86_phys_bits adjustment corruption
x86/olpc: Fix inconsistent MFD_CS5535 configuration
swiotlb: Use dma_direct_supported() for swiotlb_ops
syscalls/x86: Adapt syscall_wrapper.h to the new syscall stub naming convention
syscalls/core, syscalls/x86: Rename struct pt_regs-based sys_*() to __x64_sys_*()
syscalls/core, syscalls/x86: Clean up compat syscall stub naming convention
syscalls/core, syscalls/x86: Clean up syscall stub naming convention
syscalls/x86: Extend register clearing on syscall entry to lower registers
syscalls/x86: Unconditionally enable 'struct pt_regs' based syscalls on x86_64
syscalls/x86: Use 'struct pt_regs' based syscall calling for IA32_EMULATION and x32
syscalls/core: Prepare CONFIG_ARCH_HAS_SYSCALL_WRAPPER=y for compat syscalls
syscalls/x86: Use 'struct pt_regs' based syscall calling convention for 64-bit syscalls
syscalls/core: Introduce CONFIG_ARCH_HAS_SYSCALL_WRAPPER=y
x86/syscalls: Don't pointlessly reload the system call number
x86/mm: Fix documentation of module mapping range with 4-level paging
x86/cpuid: Switch to 'static const' specifier
Pull x86 pti updates from Thomas Gleixner:
"Another series of PTI related changes:
- Remove the manual stack switch for user entries from the idtentry
code. This debloats entry by 5k+ bytes of text.
- Use the proper types for the asm/bootparam.h defines to prevent
user space compile errors.
- Use PAGE_GLOBAL for !PCID systems to gain back performance
- Prevent setting of huge PUD/PMD entries when the entries are not
leaf entries otherwise the entries to which the PUD/PMD points to
and are populated get lost"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pgtable: Don't set huge PUD/PMD on non-leaf entries
x86/pti: Leave kernel text global for !PCID
x86/pti: Never implicitly clear _PAGE_GLOBAL for kernel image
x86/pti: Enable global pages for shared areas
x86/mm: Do not forbid _PAGE_RW before init for __ro_after_init
x86/mm: Comment _PAGE_GLOBAL mystery
x86/mm: Remove extra filtering in pageattr code
x86/mm: Do not auto-massage page protections
x86/espfix: Document use of _PAGE_GLOBAL
x86/mm: Introduce "default" kernel PTE mask
x86/mm: Undo double _PAGE_PSE clearing
x86/mm: Factor out pageattr _PAGE_GLOBAL setting
x86/entry/64: Drop idtentry's manual stack switch for user entries
x86/uapi: Fix asm/bootparam.h userspace compilation errors
For s390 new kernels are loaded to fixed addresses in memory before they
are booted. With the current code this is a problem as it assumes the
kernel will be loaded to an 'arbitrary' address. In particular,
kexec_locate_mem_hole searches for a large enough memory region and sets
the load address (kexec_bufer->mem) to it.
Luckily there is a simple workaround for this problem. By returning 1
in arch_kexec_walk_mem, kexec_locate_mem_hole is turned off. This
allows the architecture to set kbuf->mem by hand. While the trick works
fine for the kernel it does not for the purgatory as here the
architectures don't have access to its kexec_buffer.
Give architectures access to the purgatories kexec_buffer by changing
kexec_load_purgatory to take a pointer to it. With this change
architectures have access to the buffer and can edit it as they need.
A nice side effect of this change is that we can get rid of the
purgatory_info->purgatory_load_address field. As now the information
stored there can directly be accessed from kbuf->mem.
Link: http://lkml.kernel.org/r/20180321112751.22196-11-prudo@linux.vnet.ibm.com
Signed-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While prepare_elf64_headers() in x86 looks pretty generic for other
architectures' use, it contains some code which tries to list crash
memory regions by walking through system resources, which is not always
architecture agnostic. To make this function more generic, the related
code should be purged.
In this patch, prepare_elf64_headers() simply scans crash_mem buffer
passed and add all the listed regions to elf header as a PT_LOAD
segment. So walk_system_ram_res(prepare_elf64_headers_callback) have
been moved forward before prepare_elf64_headers() where the callback,
prepare_elf64_headers_callback(), is now responsible for filling up
crash_mem buffer.
Meanwhile exclude_elf_header_ranges() used to be called every time in
this callback it is rather redundant and now called only once in
prepare_elf_headers() as well.
Link: http://lkml.kernel.org/r/20180306102303.9063-4-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Tested-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull parisc updates from Helge Deller:
- fix panic when halting system via "shutdown -h now"
- drop own coding in favour of generic CONFIG_COMPAT_BINFMT_ELF
implementation
- add FPE_CONDTRAP constant: last outstanding parisc-specific cleanup
for Eric Biedermans siginfo patches
- move some functions to .init and some to .text.hot linker sections
* 'parisc-4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Prevent panic at system halt
parisc: Switch to generic COMPAT_BINFMT_ELF
parisc: Move cache flush functions into .text.hot section
parisc/signal: Add FPE_CONDTRAP for conditional trap handling
Posix and common sense requires that SI_USER not be a signal specific
si_code. Thus add a new FPE_CONDTRAP si_code for conditional traps.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
The APIC ID as parsed from ACPI MADT is validity checked with the
apic->apic_id_valid() callback, which depends on the selected APIC type.
For non X2APIC types APIC IDs >= 0xFF are invalid, but values > 0x7FFFFFFF
are detected as valid. This happens because the 'apicid' argument of the
apic_id_valid() callback is type 'int'. So the resulting comparison
apicid < 0xFF
evaluates to true for all unsigned int values > 0x7FFFFFFF which are handed
to default_apic_id_valid(). As a consequence, invalid APIC IDs in !X2APIC
mode are considered valid and accounted as possible CPUs.
Change the apicid argument type of the apic_id_valid() callback to u32 so
the evaluation is unsigned and returns the correct result.
[ tglx: Massaged changelog ]
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Cc: jgross@suse.com
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/1523322966-10296-1-git-send-email-lirongqing@baidu.com
Some features (Intel MKTME, AMD SME) reduce the number of effectively
available physical address bits. cpuinfo_x86::x86_phys_bits is adjusted
accordingly during the early cpu feature detection.
Though if get_cpu_cap() is called later again then this adjustement is
overwritten. That happens in setup_pku(), which is called after
detect_tme().
To address this, extract the address sizes enumeration into a separate
function, which is only called only from early_identify_cpu() and from
generic_identify().
This makes get_cpu_cap() safe to be called later during boot proccess
without overwriting cpuinfo_x86::x86_phys_bits.
[ tglx: Massaged changelog ]
Fixes: cb06d8e3d0 ("x86/tme: Detect if TME and MKTME is activated by BIOS")
Reported-by: Kai Huang <kai.huang@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: linux-mm@kvack.org
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: https://lkml.kernel.org/r/20180410092704.41106-1-kirill.shutemov@linux.intel.com
Pull kvm updates from Paolo Bonzini:
"ARM:
- VHE optimizations
- EL2 address space randomization
- speculative execution mitigations ("variant 3a", aka execution past
invalid privilege register access)
- bugfixes and cleanups
PPC:
- improvements for the radix page fault handler for HV KVM on POWER9
s390:
- more kvm stat counters
- virtio gpu plumbing
- documentation
- facilities improvements
x86:
- support for VMware magic I/O port and pseudo-PMCs
- AMD pause loop exiting
- support for AMD core performance extensions
- support for synchronous register access
- expose nVMX capabilities to userspace
- support for Hyper-V signaling via eventfd
- use Enlightened VMCS when running on Hyper-V
- allow userspace to disable MWAIT/HLT/PAUSE vmexits
- usual roundup of optimizations and nested virtualization bugfixes
Generic:
- API selftest infrastructure (though the only tests are for x86 as
of now)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (174 commits)
kvm: x86: fix a prototype warning
kvm: selftests: add sync_regs_test
kvm: selftests: add API testing infrastructure
kvm: x86: fix a compile warning
KVM: X86: Add Force Emulation Prefix for "emulate the next instruction"
KVM: X86: Introduce handle_ud()
KVM: vmx: unify adjacent #ifdefs
x86: kvm: hide the unused 'cpu' variable
KVM: VMX: remove bogus WARN_ON in handle_ept_misconfig
Revert "KVM: X86: Fix SMRAM accessing even if VM is shutdown"
kvm: Add emulation for movups/movupd
KVM: VMX: raise internal error for exception during invalid protected mode state
KVM: nVMX: Optimization: Dont set KVM_REQ_EVENT when VMExit with nested_run_pending
KVM: nVMX: Require immediate-exit when event reinjected to L2 and L1 event pending
KVM: x86: Fix misleading comments on handling pending exceptions
KVM: x86: Rename interrupt.pending to interrupt.injected
KVM: VMX: No need to clear pending NMI/interrupt on inject realmode interrupt
x86/kvm: use Enlightened VMCS when running on Hyper-V
x86/hyper-v: detect nested features
x86/hyper-v: define struct hv_enlightened_vmcs and clean field bits
...
