Let drivers advertise support for AP-mode WPA/WPA2-PSK 4-way handshake
offloading with a new NL80211_EXT_FEATURE_4WAY_HANDSHAKE_AP_PSK flag.
Extend use of NL80211_ATTR_PMK attribute indicating it might be passed
as part of NL80211_CMD_START_AP command, and contain the PSK (which is
the PMK, hence the name).
The driver is assumed to handle the 4-way handshake by itself in this
case, instead of relying on userspace.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Link: https://lore.kernel.org/r/20200623134938.39997-2-chi-hsien.lin@cypress.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, before being able to forward a packet between two 802.11s
nodes, both a PLINK handshake is performed upon receiving a beacon and
then later a PREQ/PREP exchange for path discovery is performed on
demand upon receiving a data frame to forward.
When running a mesh protocol on top of an 802.11s interface, like
batman-adv, we do not need the multi-hop mesh routing capabilities of
802.11s and usually set mesh_fwding=0. However, even with mesh_fwding=0
the PREQ/PREP path discovery is still performed on demand. Even though
in this scenario the next hop PREQ/PREP will determine is always the
direct 11s neighbor node.
The new mesh_nolearn parameter allows to skip the PREQ/PREP exchange in
this scenario, leading to a reduced delay, reduced packet buffering and
simplifies HWMP in general.
mesh_nolearn is still rather conservative in that if the packet destination
is not a direct 11s neighbor, it will fall back to PREQ/PREP path
discovery.
For normal, multi-hop 802.11s mesh routing it is usually not advisable
to enable mesh_nolearn as a transmission to a direct but distant neighbor
might be worse than reaching that same node via a more robust /
higher throughput etc. multi-hop path.
Cc: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Link: https://lore.kernel.org/r/20200617073034.26149-1-linus.luessing@c0d3.blue
[fix nl80211 policy to range 0/1 only]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver advertises NL80211_EXT_FEATURE_SCAN_FREQ_KHZ
userspace can omit NL80211_ATTR_SCAN_FREQUENCIES in favor
of an NL80211_ATTR_SCAN_FREQ_KHZ. To get scan results in
KHz userspace must also set the
NL80211_SCAN_FLAG_FREQ_KHZ.
This lets nl80211 remain compatible with older userspaces
while not requring and sending redundant (and potentially
incorrect) scan frequency sets.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200430172554.18383-4-thomas@adapt-ip.com
[use just nla_nest_start() (not _noflag) for NL80211_ATTR_SCAN_FREQ_KHZ]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211 recently gained the ability to understand a
frequency offset component in KHz. Expose this in nl80211
through the new attributes NL80211_ATTR_WIPHY_FREQ_OFFSET,
NL80211_FREQUENCY_ATTR_OFFSET,
NL80211_ATTR_CENTER_FREQ1_OFFSET, and
NL80211_BSS_FREQUENCY_OFFSET.
These add support to send and receive a KHz offset
component with the following NL80211 commands:
- NL80211_CMD_FRAME
- NL80211_CMD_GET_SCAN
- NL80211_CMD_AUTHENTICATE
- NL80211_CMD_ASSOCIATE
- NL80211_CMD_CONNECT
Along with any other command which takes a chandef, ie:
- NL80211_CMD_SET_CHANNEL
- NL80211_CMD_SET_WIPHY
- NL80211_CMD_START_AP
- NL80211_CMD_RADAR_DETECT
- NL80211_CMD_NOTIFY_RADAR
- NL80211_CMD_CHANNEL_SWITCH
- NL80211_JOIN_IBSS
- NL80211_CMD_REMAIN_ON_CHANNEL
- NL80211_CMD_JOIN_OCB
- NL80211_CMD_JOIN_MESH
- NL80211_CMD_TDLS_CHANNEL_SWITCH
If the driver advertises a band containing channels with
frequency offset, it must also verify support for
frequency offset channels in its cfg80211 ops, or return
an error.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200430172554.18383-3-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current rule for applying TID configuration for specific peer looks overly
complicated. No need to reject new TID configuration when override flag is
specified. Another call with the same TID configuration, but without
override flag, allows to apply new configuration anyway.
Use the same approach as for the 'all peers' case: if override flag is
specified, then reset existing TID configuration and immediately
apply a new one.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200424112905.26770-5-sergey.matyukevich.os@quantenna.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend cfg80211_rx_unprot_mlme_mgmt() to cover indication of unprotected
Beacon frames in addition to the previously used Deauthentication and
Disassociation frames. The Beacon frame case is quite similar, but has
couple of exceptions: this is used both with fully unprotected and also
incorrectly protected frames and there is a rate limit on the events to
avoid unnecessary flooding netlink events in case something goes wrong.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200401142548.6990-1-jouni@codeaurora.org
[add missing kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers that trigger roaming need to know the lifetime of the configured
PMKSA for deciding whether to trigger the full or PMKSA cache based
authentication. The configured PMKSA is invalid after the PMK lifetime
has expired and must not be used after that and the STA needs to
disassociate if the PMK expires. Hence the STA is expected to refresh
the PMK with a full authentication before this happens (e.g., when
reassociating to a new BSS the next time or by performing EAPOL
reauthentication depending on the AKM) to avoid unnecessary
disconnection.
The PMK reauthentication threshold is the percentage of the PMK lifetime
value and indicates to the driver to trigger a full authentication roam
(without PMKSA caching) after the reauthentication threshold time, but
before the PMK timer has expired. Authentication methods like SAE need
to be able to generate a new PMKSA entry without having to force a
disconnection after this threshold timeout. If no roaming occurs between
the reauthentication threshold time and PMK lifetime expiration,
disassociation is still forced.
The new attributes for providing these values correspond to the dot11
MIB variables dot11RSNAConfigPMKLifetime and
dot11RSNAConfigPMKReauthThreshold.
This type of functionality is already available in cases where user
space component is in control of roaming. This commit extends that same
capability into cases where parts or all of this functionality is
offloaded to the driver.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200312235903.18462-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes, userspace is able to detect that a peer silently lost its
state (like, if the peer reboots). wpa_supplicant does this for IBSS-RSN
by registering for auth/deauth frames, but when it detects this, it is
only able to remove the encryption keys of the peer and close its port.
However, the kernel also hold other state about the station, such as BA
sessions, probe response parameters and the like. They also need to be
resetted correctly.
This patch adds the NL80211_EXT_FEATURE_DEL_IBSS_STA feature flag
indicating the driver accepts deleting stations in IBSS mode, which
should send a deauth and reset the state of the station, just like in
mesh point mode.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Link: https://lore.kernel.org/r/20200305135754.12094-1-cavallar@lri.fr
[preserve -EINVAL return]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the nl80211 control port is used before this patch, pre-auth frames
(0x88c7) are send to userspace uncoditionally. While this enables userspace
to only use nl80211 on the station side, it is not always useful for APs.
Furthermore, pre-auth frames are ordinary data frames and not related to
the control port. Therefore it should for example be possible for pre-auth
frames to be bridged onto a wired network on AP side without touching
userspace.
For backwards compatibility to code already using pre-auth over nl80211,
this patch adds a feature flag to disable this behavior, while it remains
enabled by default. An additional ext. feature flag is added to detect this
from userspace.
Thanks to Jouni for pointing out, that pre-auth frames should be handled as
ordinary data frames.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200312091055.54257-2-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support to configure per TID retry configuration
through the NL80211_TID_CONFIG_ATTR_RETRY_SHORT and
NL80211_TID_CONFIG_ATTR_RETRY_LONG attributes. This TID specific
retry configuration will have more precedence than phy level
configuration.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-3-git-send-email-tamizhr@codeaurora.org
[rebase completely on top of my previous API changes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make some changes to the TID-config API:
* use u16 in nl80211 (only, and restrict to using 8 bits for now),
to avoid issues in the future if we ever want to use higher TIDs.
* reject empty TIDs mask (via netlink policy)
* change feature advertising to not use extended feature flags but
have own mechanism for this, which simplifies the code
* fix all variable names from 'tid' to 'tids' since it's a mask
* change to cfg80211_ name prefixes, not ieee80211_
* fix some minor docs/spelling things.
Change-Id: Ia234d464b3f914cdeab82f540e018855be580dce
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE P802.11-REVmd/D3.0 adds support for protecting Beacon frames using
a new set of keys (BIGTK; key index 6..7) similarly to the way
group-addressed Robust Management frames are protected (IGTK; key index
4..5). Extend cfg80211 and nl80211 to allow the new BIGTK to be
configured. Add an extended feature flag to indicate driver support for
the new key index values to avoid array overflows in driver
implementations and also to indicate to user space when this
functionality is available.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200222132548.20835-2-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using control port over nl80211 in AP mode with
pre-authentication, APs need to forward frames to other
APs defined by their MAC address. Before this patch,
pre-auth frames reaching user space over nl80211 control
port have no longer any information about the dest attached,
which can be used for forwarding to a controller or injecting
the frame back to a ethernet interface over a AF_PACKET
socket.
Analog problems exist, when forwarding pre-auth frames from
AP -> STA.
This patch therefore adds the NL80211_ATTR_DST_MAC and
NL80211_ATTR_SRC_MAC attributes to provide more context
information when forwarding.
The respective arguments are optional on tx and included on rx.
Therefore unaware existing software is not affected.
Software which wants to detect this feature, can do so
by checking against:
NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211_MAC_ADDRS
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200115125522.3755-1-markus.theil@tu-ilmenau.de
[split into separate cfg80211/mac80211 patches]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit ab4dfa2053 ("cfg80211: Allow drivers to advertise supported AKM
suites") introduces the support to advertize supported AKMs to userspace.
This needs an enhancement to advertize the AKM support per interface type,
specifically for the cfg80211-based drivers that implement SME and use
different mechanisms to support the AKM's for each interface type (e.g.,
the support for SAE, OWE AKM's take different paths for such drivers on
STA/AP mode).
This commit aims the same and enhances the earlier mechanism of advertizing
the AKMs per wiphy. Add new nl80211 attributes and data structure to
provide supported AKMs per interface type to userspace.
the AKMs advertized in akm_suites are default capabilities if not
advertized for a specific interface type in iftype_akm_suites.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Link: https://lore.kernel.org/r/20200126203032.21934-1-vjakkam@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of just having an airtime flag in debugfs, turn AQL into a proper
NL80211_EXT_FEATURE, so drivers can turn it on when they are ready, and so
we also expose the presence of the feature to userspace.
This also has the effect of flipping the default, so drivers have to opt in
to using AQL instead of getting it by default with TXQs. To keep
functionality the same as pre-patch, we set this feature for ath10k (which
is where it is needed the most).
While we're at it, split out the debugfs interface so AQL gets its own
per-station debugfs file instead of using the 'airtime' file.
[Johannes:]
This effectively disables AQL for iwlwifi, where it fixes a number of
issues:
* TSO in iwlwifi is causing underflows and associated warnings in AQL
* HE (802.11ax) rates aren't reported properly so at HE rates, AQL could
never have a valid estimate (it'd use 6 Mbps instead of up to 2400!)
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191212111437.224294-1-toke@redhat.com
Fixes: 3ace10f5b5 ("mac80211: Implement Airtime-based Queue Limit (AQL)")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This provides an alternative mechanism for AP VLAN support where a
single netdev is used with VLAN tagged frames instead of separate
netdevs for each VLAN without tagged frames from the WLAN driver.
By setting NL80211_EXT_FEATURE_VLAN_OFFLOAD flag the driver indicates
support for a single netdev with VLAN tagged frames. Separate
VLAN-specific netdevs can be added using RTM_NEWLINK/IFLA_VLAN_ID
similarly to Ethernet. NL80211_CMD_NEW_KEY (for group keys),
NL80211_CMD_NEW_STATION, and NL80211_CMD_SET_STATION will optionally
specify vlan_id using NL80211_ATTR_VLAN_ID.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20191031214640.5012-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit documents the expectation for NL80211_ATTR_IE when included
in NL80211_CMD_CONNECT, as following.
Driver shall not modify the IEs specified through NL80211_ATTR_IE if
NL80211_ATTR_MAC is included. However, if NL80211_ATTR_MAC_HINT is
included, these IEs through NL80211_ATTR_IE are specified by the user
space based on the best possible BSS selected. Thus, if the driver ends
up selecting a different BSS, it can modify these IEs accordingly (e.g.
userspace asks the driver to perform PMKSA caching with BSS1 and the
driver ends up selecting BSS2 with different PMKSA cache entry. RSNIE
has to get updated with the apt PMKID).
Signed-off-by: Sunil Dutt <usdutt@codeaurora.org>
Link: https://lore.kernel.org/r/1568378504-15179-1-git-send-email-usdutt@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
802.11ay specification defines Enhanced Directional Multi-Gigabit
(EDMG) STA and AP which allow channel bonding of 2 channels and more.
Introduce new NL attributes that are needed for enabling and
configuring EDMG support.
Two new attributes are used by kernel to publish driver's EDMG
capabilities to the userspace:
NL80211_BAND_ATTR_EDMG_CHANNELS - bitmap field that indicates the 2.16
GHz channel(s) that are supported by the driver.
When this attribute is not set it means driver does not support EDMG.
NL80211_BAND_ATTR_EDMG_BW_CONFIG - represent the channel bandwidth
configurations supported by the driver.
Additional two new attributes are used by the userspace for connect
command and for AP configuration:
NL80211_ATTR_WIPHY_EDMG_CHANNELS
NL80211_ATTR_WIPHY_EDMG_BW_CONFIG
New rate info flag - RATE_INFO_FLAGS_EDMG, can be reported from driver
and used for bitrate calculation that will take into account EDMG
according to the 802.11ay specification.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Link: https://lore.kernel.org/r/1566138918-3823-2-git-send-email-ailizaro@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Shifting signed 32-bit value by 31 bits is undefined. Changing most
significant bit to unsigned.
Signed-off-by: Jiunn Chang <c0d1n61at3@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow the userland daemon to en/disable TWT support for an AP.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
[simplify parsing code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Let drivers advertise support for station-mode SAE authentication
offload with a new NL80211_EXT_FEATURE_SAE_OFFLOAD flag.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
