There is code for adjusting the clock both in setup_fifo_params()
(called from prepare_message()) and in setup_fifo_xfer() (called from
transfer_one()). The code is the same. Abstract it out to a shared
function.
This is a no-op cleanup patch. The only change is to the error string
if we fail to set the clock. Since the two paths has marginally
different error messages I picked the clean one.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/1592908737-7068-6-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add fallback to pio mode in case dma transfer failed with error status
SPI_TRANS_FAIL_NO_START.
If spi client driver want to enable this feature please set xfer->error in
the proper place such as dmaengine_prep_slave_sg() failure detect(but no
any data put into spi bus yet). Besides, add master->fallback checking in
its can_dma() so that spi core could switch to pio next time. Please refer
to spi-imx.c.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/1592347329-28363-2-git-send-email-yibin.gong@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull spi fixes from Mark Brown:
"Quite a lot of fixes here for no single reason.
There's a collection of the usual sort of device specific fixes and
also a bunch of people have been working on spidev and the userspace
test program spidev_test so they've got an unusually large collection
of small fixes"
* tag 'spi-fix-v5.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spidev: fix a potential use-after-free in spidev_release()
spi: spidev: fix a race between spidev_release and spidev_remove
spi: stm32-qspi: Fix error path in case of -EPROBE_DEFER
spi: uapi: spidev: Use TABs for alignment
spi: spi-fsl-dspi: Free DMA memory with matching function
spi: tools: Add macro definitions to fix build errors
spi: tools: Make default_tx/rx and input_tx static
spi: dt-bindings: amlogic, meson-gx-spicc: Fix schema for meson-g12a
spi: rspi: Use requested instead of maximum bit rate
spi: spidev_test: Use %u to format unsigned numbers
spi: sprd: switch the sequence of setting WDG_LOAD_LOW and _HIGH
To follow onto Doug's latest spi geni series[1] this simplifies and
reduces the code a little more.
[1] https://lore.kernel.org/r/20200618150626.237027-1-dianders@chromium.org
Stephen Boyd (2):
spi: spi-geni-qcom: Simplify setup_fifo_xfer()
spi: spi-geni-qcom: Don't set {tx,rx}_rem_bytes unnecessarily
drivers/spi/spi-geni-qcom.c | 55 +++++++++++++++++--------------------
1 file changed, 25 insertions(+), 30 deletions(-)
base-commit: 7ba9bdcb91
--
Sent by a computer, using git, on the internet
We only need to test for these counters being non-zero when we see the
end of a transfer. If we're doing a CS change then they will already be
zero. This implies that we don't need to set these to 0 if we're
cancelling an in flight transfer too, because we only care to test these
counters when the 'DONE' bit is set in the hardware and we've set them
to non-zero for a transfer.
This is a non-functional change, just cleanup to consolidate code.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200620022233.64716-3-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The definition of SPI_FULL_DUPLEX (3) is really SPI_TX_ONLY (1) ORed
with SPI_RX_ONLY (2). Let's drop the define and simplify the code here a
bit by collapsing the setting of 'm_cmd' into conditions that are the
same.
This is a non-functional change, just cleanup to consolidate code.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200620022233.64716-2-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
If shared interrupt comes late, during probe error path or device remove
(could be triggered with CONFIG_DEBUG_SHIRQ), the interrupt handler
dspi_interrupt() will access registers with the clock being disabled.
This leads to external abort on non-linefetch on Toradex Colibri VF50
module (with Vybrid VF5xx):
$ echo 4002d000.spi > /sys/devices/platform/soc/40000000.bus/4002d000.spi/driver/unbind
Unhandled fault: external abort on non-linefetch (0x1008) at 0x8887f02c
Internal error: : 1008 [#1] ARM
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
Backtrace:
(regmap_mmio_read32le)
(regmap_mmio_read)
(_regmap_bus_reg_read)
(_regmap_read)
(regmap_read)
(dspi_interrupt)
(free_irq)
(devm_irq_release)
(release_nodes)
(devres_release_all)
(device_release_driver_internal)
The resource-managed framework should not be used for shared interrupt
handling, because the interrupt handler might be called after releasing
other resources and disabling clocks.
Similar bug could happen during suspend - the shared interrupt handler
could be invoked after suspending the device. Each device sharing this
interrupt line should disable the IRQ during suspend so handler will be
invoked only in following cases:
1. None suspended,
2. All devices resumed.
Fixes: 349ad66c0a ("spi:Add Freescale DSPI driver for Vybrid VF610 platform")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-3-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
During device removal, the driver should unregister the SPI controller
and stop the hardware. Otherwise the dspi_transfer_one_message() could
wait on completion infinitely.
Additionally, calling spi_unregister_controller() first in device
removal reverse-matches the probe function, where SPI controller is
registered at the end.
Fixes: 05209f4570 ("spi: fsl-dspi: add missing clk_disable_unprepare() in dspi_remove()")
Reported-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This series is a subset of "[PATCH v12 0/4] spi: cadence-quadspi: Add
support for the Cadence QSPI controller" by Ramuthevar,Vadivel MuruganX
<vadivel.muruganx.ramuthevar@linux.intel.com> that intended to move
cadence-quadspi driver to spi-mem framework
Those patches were trying to accomplish too many things in a single set
of patches and need to split into smaller patches. This is reduced
version of above series.
Changes that are intended to make migration easy are split into separate
patches. Patches 1 to 3 drop features that cannot be supported under
spi-mem at the moment (backward compatibility is maintained).
Patch 4-5 are trivial cleanups. Patch 6 does the actual conversion to
spi-mem and patch 7 moves the driver to drivers/spi folder.
I have tested both INDAC mode (used by non TI platforms like Altera
SoCFPGA) and DAC mode (used by TI platforms) on TI EVMs.
Patches to move move bindings over to
"Documentation/devicetree/bindings/spi/" directory and also conversion
of bindig doc to YAML will be posted separately. Support for Intel
platform would follow that.
Resend v3:
Rebased onto v5.7-c1
v3:
Split handling of probe deferral into separate patch (out of 5/6)
Split dropping of redundant WREN to separate patch (out of 5/6)
Fix a possible memleak due to lack of spi_master_put()
Parse all SPI slave nodes in cqspi_setup_flash()
Address misc comments from Tudor on v2
Rebase onto latest spi-nor/next
v2:
Rework patch 1/6 to keep "cdns,is-decoded-cs" property supported.
Ramuthevar Vadivel Murugan (2):
mtd: spi-nor: Convert cadence-quadspi to use spi-mem framework
spi: Move cadence-quadspi driver to drivers/spi/
Vignesh Raghavendra (6):
mtd: spi-nor: cadence-quadspi: Make driver independent of flash
geometry
mtd: spi-nor: cadence-quadspi: Provide a way to disable DAC mode
mtd: spi-nor: cadence-quadspi: Don't initialize rx_dma_complete on
failure
mtd: spi-nor: cadence-quadspi: Fix error path on failure to acquire
reset lines
mtd: spi-nor: cadence-quadspi: Handle probe deferral while requesting
DMA channel
mtd: spi-nor: cadence-quadspi: Drop redundant WREN in erase path
drivers/mtd/spi-nor/controllers/Kconfig | 11 -
drivers/mtd/spi-nor/controllers/Makefile | 1 -
drivers/spi/Kconfig | 11 +
drivers/spi/Makefile | 1 +
.../spi-cadence-quadspi.c} | 541 +++++++-----------
5 files changed, 222 insertions(+), 343 deletions(-)
rename drivers/{mtd/spi-nor/controllers/cadence-quadspi.c => spi/spi-cadence-quadspi.c} (74%)
base-commit: b3a9e3b962
--
2.26.2
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Updated the regmap & indirect access support for spi-altera.
Patch #1 is an 1:1 replacement of of readl/writel with regmap_read/write
Patch #2 introduced a new platform_device_id to support indirect access as
a sub device.
Patch #3 is a minor fix.
Main changes from v1:
- Split the regmap supporting patch to 2 patches.
- Add a new platform_device_id to support indirect access.
- Removed the v1 patch "move driver name string to header file". Now we
use driver name string directly.
- Add Yilun's Signed-off-by for Patch #3.
- Add Tom's Reviewed-by.
Matthew Gerlach (1):
spi: altera: fix size mismatch on 64 bit processors
Xu Yilun (2):
spi: altera: use regmap-mmio instead of direct mmio register access
spi: altera: support indirect access to the registers
drivers/spi/Kconfig | 1 +
drivers/spi/spi-altera.c | 127 +++++++++++++++++++++++++++++++++++++++--------
2 files changed, 107 insertions(+), 21 deletions(-)
--
2.7.4
This patch series is a new version of the previous patch posted:
[PATCH v2] spi: spi-geni-qcom: Speculative fix of "nobody cared" about interrupt
https://lore.kernel.org/r/20200317133653.v2.1.I752ebdcfd5e8bf0de06d66e767b8974932b3620e@changeid
At this point I've done enough tracing to know that there was a real
race in the old code (not just weakly ordered memory problems) and
that should be fixed with the locking patches.
While looking at this driver, I also noticed we weren't properly
noting error interrupts and also weren't actually using our FIFO
effectively, so I fixed those.
The last patch in the series addresses review feedback about dislike
for the "cur_mcmd" state variable. It also could possibly make
"abort" work ever-so-slightly more reliably.
Changes in v4:
- Drop 'controller' in comment.
- Use Stephen's diagram to explain the race better.
Changes in v3:
- ("spi: spi-geni-qcom: No need for irqsave variant...") new for v3
- Split out some lock cleanup to previous patch.
- Don't need to read IRQ status register inside spinlock.
- Don't check for state CMD_NONE; later patch is removing state var.
- Don't hold the lock for all of setup_fifo_xfer().
- Comment about why it's safe to Ack interrupts at the end.
- Subject/desc changed since race is definitely there.
- ("spi: spi-geni-qcom: Check for error IRQs") new in v3.
- ("spi: spi-geni-qcom: Actually use our FIFO") new in v3.
- ("spi: spi-geni-qcom: Don't keep a local state variable") new in v3.
Changes in v2:
- Detect true spurious interrupt.
- Still return IRQ_NONE for state machine mismatch, but print warn.
Douglas Anderson (5):
spi: spi-geni-qcom: No need for irqsave variant of spinlock calls
spi: spi-geni-qcom: Mo' betta locking
spi: spi-geni-qcom: Check for error IRQs
spi: spi-geni-qcom: Actually use our FIFO
spi: spi-geni-qcom: Don't keep a local state variable
drivers/spi/spi-geni-qcom.c | 120 ++++++++++++++++++++++++------------
1 file changed, 81 insertions(+), 39 deletions(-)
--
2.27.0.290.gba653c62da-goog
The variable "cur_mcmd" kept track of our current state (idle, xfer,
cs, cancel). We don't really need it, so get rid of it. Instead:
* Use separate condition variables for "chip select done", "cancel
done", and "abort done". This is important so that if a "done"
comes through (perhaps some previous interrupt finally came through)
it can't confuse the cancel/abort function.
* Use the "done" interrupt only for when a chip select or transfer is
done and we can tell the difference by looking at whether "cur_xfer"
is NULL.
This is mostly a no-op change. However, it is possible it could fix
an issue where a super delayed interrupt for a cancel command could
have confused our waiting for an abort command.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200618080459.v4.5.Ib1e6855405fc9c99916ab7c7dee84d73a8bf3d68@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
The geni hardware has a FIFO that can hold up to 64 bytes (it has 16
entries that can hold 4 bytes each), at least on the two SoCs I tested
(sdm845 and sc7180). We configured our RX Watermark to 0, which
basically meant we got an interrupt as soon as the first 4 bytes
showed up in the FIFO. Tracing the IRQ handler showed that we often
only read 4 or 8 bytes per IRQ handler.
I tried setting the RX Watermark to "fifo size - 2" but that just got
me a bunch of overrun errors reported. Setting it to "fifo size - 3"
seemed to work great, though. This made me worried that we'd start
getting overruns if we had long interrupt latency, but that doesn't
appear to be the case and delays inserted in the IRQ handler while
using "fifo size - 3" didn't cause any errors. Presumably there is
some interaction with the poorly-documented RFR (ready for receive)
level means that "fifo size - 3" is the max. We are the SPI master,
so it makes sense that there would be no problems with overruns, the
master should just stop clocking.
Despite "fifo size - 3" working, I chose "fifo size / 2" (8 entries =
32 bytes) which gives us a little extra time to get to the interrupt
handler and should reduce dead time on the SPI wires. With this
setting, I often saw the IRQ handler handle 40 bytes but sometimes up
to 56 if we had bad interrupt latency.
Testing by running "flashrom -p ec -r" on a Chromebook saw interrupts
from the SPI driver cut roughly in half. Time was roughly the same.
Fixes: 561de45f72 ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200618080459.v4.4.I988281f7c6ee0ed00325559bfce7539f403da69e@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
If you added a bit of a delay (like a trace_printk) into the ISR for
the spi-geni-qcom driver, you would suddenly start seeing some errors
spit out. The problem was that, though the ISR itself held a lock,
other parts of the driver didn't always grab the lock.
One example race was this:
CPU0 CPU1
---- ----
spi_geni_set_cs()
mas->cur_mcmd = CMD_CS;
geni_se_setup_m_cmd(...)
wait_for_completion_timeout(&xfer_done);
<INTERRUPT>
geni_spi_isr()
complete(&xfer_done);
<wakeup>
pm_runtime_put(mas->dev);
... // back to SPI core
spi_geni_transfer_one()
setup_fifo_xfer()
mas->cur_mcmd = CMD_XFER;
mas->cur_cmd = CMD_NONE; // bad!
return IRQ_HANDLED;
Let's fix this. Before we start messing with hardware, we'll grab the
lock to make sure that the IRQ handler from some previous command has
really finished. We don't need to hold the lock unless we're in a
state where more interrupts can come in, but we at least need to make
sure the previous IRQ is done. This lock is used exclusively to
prevent the IRQ handler and non-IRQ from stomping on each other. The
SPI core handles all other mutual exclusion.
As part of this, we change the way that the IRQ handler detects
spurious interrupts. Previously we checked for our state variable
being set to IRQ_NONE, but that was done outside the spinlock. We
could move it into the spinlock, but instead let's just change it to
look for the lack of any IRQ status bits being set. This can be done
outside the lock--the hardware certainly isn't grabbing or looking at
the spinlock when it updates its status register.
It's possible that this will fix real (but very rare) errors seen in
the field that look like:
irq ...: nobody cared (try booting with the "irqpoll" option)
NOTE: an alternate strategy considered here was to always make the
complete() / spi_finalize_current_transfer() the very last thing in
our IRQ handler. With such a change you could consider that we could
be "lockless". In that case, though, we'd have to be very careful w/
memory barriers so we made sure we didn't have any bugs with weakly
ordered memory. Using spinlocks makes the driver much easier to
understand.
Fixes: 561de45f72 ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200618080459.v4.2.I752ebdcfd5e8bf0de06d66e767b8974932b3620e@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver locks its locks in two places.
In the first usage of the lock the function doing the locking already
has a sleeping call and thus we know we can't be called from interrupt
context. That means we can use the "spin_lock_irq" variant of the
function.
In the second usage of the lock the function is the interrupt handler
and we know interrupt handlers are called with interrupts disabled.
That means we can use the "spin_lock" variant of the function.
This patch is expected to be a no-op and is just a cleanup / slight
optimization.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200616034044.v3.1.Ic50cccdf27d42420a63485082f8b5bf86ed1a2b6@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of -EPROBE_DEFER, stm32_qspi_release() was called
in any case which unregistered driver from pm_runtime framework
even if it has not been registered yet to it. This leads to:
stm32-qspi 58003000.spi: can't setup spi0.0, status -13
spi_master spi0: spi_device register error /soc/spi@58003000/mx66l51235l@0
spi_master spi0: Failed to create SPI device for /soc/spi@58003000/mx66l51235l@0
stm32-qspi 58003000.spi: can't setup spi0.1, status -13
spi_master spi0: spi_device register error /soc/spi@58003000/mx66l51235l@1
spi_master spi0: Failed to create SPI device for /soc/spi@58003000/mx66l51235l@1
On v5.7 kernel,this issue was not "visible", qspi driver was probed
successfully.
Fixes: 9d282c17b0 ("spi: stm32-qspi: Add pm_runtime support")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20200616113035.4514-1-patrice.chotard@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patchset adds platform_data for spi-altera, to enable more IP
configurations, and creating specific spi client devices. It also adds
regmap support, to enable the indirect access to this IP.
We have a PCIE based FPGA platform which integrates this IP to communicate
with a BMC chip (Intel MAX10) over SPI. The IP is configured as 32bit data
width. There is also an indirect access interface in FPGA for host to
access the registers of this IP. This patchset enables this use case.
Matthew Gerlach (1):
spi: altera: fix size mismatch on 64 bit processors
Xu Yilun (5):
spi: altera: add 32bit data width transfer support.
spi: altera: add SPI core parameters support via platform data.
spi: altera: add platform data for slave information.
spi: altera: use regmap instead of direct mmio register access
spi: altera: move driver name string to header file
drivers/spi/Kconfig | 1 +
drivers/spi/spi-altera.c | 161 +++++++++++++++++++++++++++++++++++++--------
include/linux/spi/altera.h | 37 +++++++++++
3 files changed, 171 insertions(+), 28 deletions(-)
create mode 100644 include/linux/spi/altera.h
--
2.7.4
The OcteonTX (TX1/ThunderX) SPI controller does not support full
duplex transactions. Set the appropriate flag such that the spi
core will return -EINVAL on such transactions requested by chip
drivers.
This is an RFC as I need someone from Marvell/Cavium to confirm
if this driver is used for other silicon that does support
full duplex transfers (in which case we will need to identify
that we are running on the ThunderX arch before setting the flag).
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Cc: Robert Richter <rrichter@marvell.com>
Link: https://lore.kernel.org/r/1590680799-5640-1-git-send-email-tharvey@gateworks.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Because SCHED_FIFO is a broken scheduler model (see previous patches)
take away the priority field, the kernel can't possibly make an
informed decision.
No effective change.
Cc: broonie@kernel.org
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Driver allocates DMA memory with dma_alloc_coherent() but frees it with
dma_unmap_single().
This causes DMA warning during system shutdown (with DMA debugging) on
Toradex Colibri VF50 module:
WARNING: CPU: 0 PID: 1 at ../kernel/dma/debug.c:1036 check_unmap+0x3fc/0xb04
DMA-API: fsl-edma 40098000.dma-controller: device driver frees DMA memory with wrong function
[device address=0x0000000087040000] [size=8 bytes] [mapped as coherent] [unmapped as single]
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
(unwind_backtrace) from [<8010bb34>] (show_stack+0x10/0x14)
(show_stack) from [<8011ced8>] (__warn+0xf0/0x108)
(__warn) from [<8011cf64>] (warn_slowpath_fmt+0x74/0xb8)
(warn_slowpath_fmt) from [<8017d170>] (check_unmap+0x3fc/0xb04)
(check_unmap) from [<8017d900>] (debug_dma_unmap_page+0x88/0x90)
(debug_dma_unmap_page) from [<80601d68>] (dspi_release_dma+0x88/0x110)
(dspi_release_dma) from [<80601e4c>] (dspi_shutdown+0x5c/0x80)
(dspi_shutdown) from [<805845f8>] (device_shutdown+0x17c/0x220)
(device_shutdown) from [<80143ef8>] (kernel_restart+0xc/0x50)
(kernel_restart) from [<801441cc>] (__do_sys_reboot+0x18c/0x210)
(__do_sys_reboot) from [<80100060>] (ret_fast_syscall+0x0/0x28)
DMA-API: Mapped at:
dma_alloc_attrs+0xa4/0x130
dspi_probe+0x568/0x7b4
platform_drv_probe+0x6c/0xa4
really_probe+0x208/0x348
driver_probe_device+0x5c/0xb4
Fixes: 90ba37033c ("spi: spi-fsl-dspi: Add DMA support for Vybrid")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1591803717-11218-1-git-send-email-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the RSPI driver always tries to use the maximum configured
bit rate for communicating with a slave device, even if the transfer(s)
in the current message specify a lower rate.
Use the mininum rate specified in the message instead.
Rename rspi_data.max_speed_hz accordingly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200608095940.30516-3-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (233 commits)
habanalabs: correctly cast u64 to void*
habanalabs: initialize variable to default value
extcon: arizona: Fix runtime PM imbalance on error
extcon: max14577: Add proper dt-compatible strings
extcon: adc-jack: Fix an error handling path in 'adc_jack_probe()'
extcon: remove redundant assignment to variable idx
w1: omap-hdq: print dev_err if irq flags are not cleared
w1: omap-hdq: fix interrupt handling which did show spurious timeouts
w1: omap-hdq: fix return value to be -1 if there is a timeout
w1: omap-hdq: cleanup to add missing newline for some dev_dbg
/dev/mem: Revoke mappings when a driver claims the region
misc: xilinx-sdfec: convert get_user_pages() --> pin_user_pages()
misc: xilinx-sdfec: cleanup return value in xsdfec_table_write()
misc: xilinx-sdfec: improve get_user_pages_fast() error handling
nvmem: qfprom: remove incorrect write support
habanalabs: handle MMU cache invalidation timeout
habanalabs: don't allow hard reset with open processes
habanalabs: GAUDI does not support soft-reset
habanalabs: add print for soft reset due to event
habanalabs: improve MMU cache invalidation code
...
