Currently need ptk/gtk wmi peer flags in wmi peer assoc cmd
are set based on the rsnie and wpaie of the bss from the bss list.
Since this bss list is not updated with current BSSID for AP mode,
we may not find bss from the bss list. Which results in ptk/gtk peer
flags are not set in the wmi peer assoc cmd. Due to this EAPOL frames
are going in data rates instead of management rates.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591771841-25503-1-git-send-email-vnaralas@codeaurora.org
Add support for collecting and dumping the ring backpressure
stats via debugfs. Stats are dumped only if events are
received for the specific ring.
Below command can be used to obtain these stats as part of soc dp stats.
cat /sys/kernel/debug/ath11k/ipq8074/soc_dp_stats
Sample Output - When No stats available:
Backpressure Stats
==================
No Ring Backpressure stats received
Sample Output - When ring bp stats available for specific ring
Backpressure Stats
==================
Ring: REO2SW1_RING
count: 1
hp: 2
tp: 2
seen before: 4ms
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591768308-32005-3-git-send-email-srirrama@codeaurora.org
Add support for dp tx error stats which logs tx failure reasons due
to ring full condition, etc. This stats is added in soc_dp_stats
which was earlier used as soc_rx_stats so that all dp related info
are logged in same file.
Below is an example usage,
root@OpenWrt:/# cat /sys/kernel/debug/ath11k/ipq8074/soc_dp_stats
SOC RX STATS:
err ring pkts: 0
Invalid RBM: 0
<snip>
SOC TX STATS:
Ring Full Failures:
ring0: 4
ring1: 3
ring2: 5
Misc Transmit Failures: 2
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591768308-32005-2-git-send-email-srirrama@codeaurora.org
spectral scan control interface is exposed through debugfs eentry.
Relayfs is used to collect the spectral data. These interfaces are
similar to ath10k spectral.
spectral debugfs interfaces are below,
echo background > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
iw dev wlan0 scan
echo disable > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan0 > fft_samples.dump
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591688014-26441-2-git-send-email-periyasa@codeaurora.org
Add direct buffer ring (dbring) with helper API, which is used by the
spectral scan. Initialise the direct buffer ring based on the dma ring
capability, which get announced in the wmi service ready extended event.
This ring is slightly changed from data path rings. Compare to data path
ring this ring shares the hp and tp address to firmware though WMI commands.
Also the replenish buffer size is derived from firmware announcement.
driver receive indication through WMI event
WMI_PDEV_DMA_RING_BUF_RELEASE_EVENTID.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591688014-26441-1-git-send-email-periyasa@codeaurora.org
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
This adds support required for configuring min_data_rate of 6GHz oper IE
and peer_he_caps_6ghz in peer assoc command. The Minimum Rate field
indicates the minimum rate, in units of 1 Mb/s, that the non-AP STA is
allowed to use for sending PPDUs as defined in IEEE P802.11ax™/D6.0.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603001724.12161-5-pradeepc@codeaurora.org
Johannes Berg says:
====================
One batch of changes, containing:
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If 'thermal_cooling_device_register()' fails, we must undo what has been
allocated so far. So we must go to 'err_thermal_destroy' instead of
returning directly
In case of error in 'ath11k_thermal_register()', the previous
'thermal_cooling_device_register()' call must also be undone. Move the
'ar->thermal.cdev = cdev' a few lines above in order for this to be done
in 'ath11k_thermal_unregister()' which is called in the error handling
path.
Fixes: 2a63bbca06 ("ath11k: add thermal cooling device support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200513201454.258111-1-christophe.jaillet@wanadoo.fr
HTT EXT stats comes in stream of TLVs spanning over multiple
messages. Currently completion is being sent for each message
which is creating a race where stats_req is being accessed
for filling in second message after the memory is already
freed in release operation. Fix this by issuing completion
once all the messages are received and processed. Driver
knows this info from DONE bit set in htt msg.
Also fix locking required for htt stats.
Co-developed-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1589221074-28778-1-git-send-email-pradeepc@codeaurora.org
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504201224.GA32282@embeddedor
htt stats are not working after htt peer stats display
and also after htt peer stats reset. Trying to dump htt
stats shows "Resource temporarily unavailable".
This is because of "ar->debug.htt_stats.stats_req" member is being
consecutively used for all htt stats without being reset
during the previous usage. Hence assigning NULL to this member
after freeing the allocated memory fixes the issue.
console logs below:
# echo 9 >/sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats_type
# cat /sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats_type
9
# cat /sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats
cat: can't open '/sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats'
: Resource temporarily unavailable
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588592755-10427-1-git-send-email-ssreeela@codeaurora.org
In Multi-AP VAP scenario with frequent interface up-down, there is a
chance that ath11k_mgmt_over_wmi_tx_work() will dequeue a skb
corresponding to currently deleted/stopped vdev.
FW will assert on receiving mgmt_tx_wmi cmd for already deleted vdev.
Hence adding validation checks for arvif present on the corresponding
ar before sending mgmt_tx_wmi cmd.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588049126-1490-2-git-send-email-murugana@codeaurora.org
As of now HE operation element in bss_conf includes variable length
optional field followed by other HE variable. Though the optional
field never be used, actually it is referring to next member of the
bss_conf structure which is not correct. Fix it by declaring needed
HE operation fields within bss_conf itself.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Link: https://lore.kernel.org/r/1587768108-25248-2-git-send-email-rmanohar@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
we are sending the reo flush command for the deleted peer
tid after the ageout period reaches 1 second. This handling
causes reo ring get full when more than 128 clients are
disconnected continuously. so added the count for flush list
and reo flush command is triggered after the list count reaches
the threshold value, it is configured as 64 (half of the reo ring).
This will avoid the situation where reo ring get full.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587552378-4884-1-git-send-email-periyasa@codeaurora.org
The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/net/wireless/ath/ath11k/debug.c:198:57-62: WARNING: conversion
to bool not needed here
drivers/net/wireless/ath/ath11k/debug.c:218:58-63: WARNING: conversion
to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420123745.4159-1-yanaijie@huawei.com
IPQ8074 HW supports three TCL rings for tx. Currently these rings
are mapped based on the Access categories, viz. VO, VI, BE, BK.
In case, one of the traffic type dominates, then it could stress
the same tcl rings. Rather, it would be optimal to make use of all
the rings in a round robin fashion irrespective of the traffic type
so that the load could be evenly distributed among all the rings.
Also, in case the selected ring is busy or full, a retry mechanism
is used to ensure other available ring is selected without dropping
the packet.
In SMP systems, this change avoids a single CPU from getting hogged
when heavy traffic of same category is transmitted.
The tx completion interrupts corresponding to the used tcl ring
would be more which causes the assigned CPU to get hogged.
Distribution of tx packets to different tcl rings helps balance
this load.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586782622-22570-1-git-send-email-srirrama@codeaurora.org
