When use one SDIO wifi which enable the runtime PM feature on i.MX6SX,
we meet system hang. This hang happened during the usdhc runtime resume,
in sdhci_init(), when call the sdhci_set_default_irqs. One interrupt
(SDHCI_INT_CARD_INT) triggered just after the host->ier update and before
the write of register SDHCI_SIGNAL_ENABLE. So in sdhci_irq, it will skip
the call of sdio_signal_irq() because current host->ier do not set the
SDHCI_INT_CARD_INT. So this SDIO wifi interrupt always keep triggered,
let the system stuck in irq handle, can't response any other thread.
This patch add spin lock for the sdhci_set_default_irqs to fix this issue.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1586941255-9237-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SD host controller can process one request in the atomic context if
the card is nonremovable, which means we can submit next request in the
irq hard handler when using the MMC host software queue to reduce the
latency. Thus this patch adds a new API request_atomic() for the host
controller, as well as adding support for host software queue to submit
a request by the new request_atomic() API.
Moreover there is an unusual case that the card is busy when trying to
send a command, and we can not polling the card status in interrupt
context by using request_atomic() to dispatch requests. Thus we should
queue a work to try again in the non-atomic context in case the host
releases the busy signal later.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/a344e27e506cb2329073cbd5cf65e15cc3cbeba9.1586744073.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Spending time under spinlock increases IRQ latencies and also
response times because preemption is disabled.
sdhci_send_command() waits up to 10 ms under spinlock for inhibit bits
to clear. In general inhibit bits will not be set, but there may be
corner cases, especially in the face of errors, where waiting helps.
There might also be dysfunctional hardware that needs the waiting. So
retain the legacy behaviour but do not wait for inhibit bits while under
spinlock. Instead adjust the logic to enable waiting while not under
spinlock. That is mostly straight forward, but in the interrupt handler
it requires deferring an "inhibited" command to the IRQ thread where
sleeping is allowed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-6-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of reimplementing the logic in mmc_regulator_set_vqmmc(), use the
mmc code function directly.
This also allows us to fix a related issue on STM32MP1, when a voltage
switch of 1.8V is done for the eMMC, but the current level is already set
to 1.8V. More precisely, in this scenario the call to the
->post_sig_volt_switch() hangs, indefinitely waiting for the voltage switch
to complete. Fix this problem by checking if mmc_regulator_set_vqmmc()
returned 1 and then skip invoking the callback.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200416163649.336967-3-marex@denx.de
[Ulf: Updated the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Patch all drivers which use mmc_regulator_set_vqmmc() and prepare them for
the fact that mmc_regulator_set_vqmmc() can return a value > 0, which would
happen if the signal voltage switch did NOT happen, because the voltage was
already set correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200416163649.336967-1-marex@denx.de
[Ulf: Re-worked/simplified the code a bit]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clang warns:
drivers/mmc/host/sdhci-of-arasan.c:784:9: warning: variable 'ret' is
uninitialized when used here [-Wuninitialized]
return ret;
^~~
drivers/mmc/host/sdhci-of-arasan.c:738:9: note: initialize the variable
'ret' to silence this warning
int ret;
^
= 0
drivers/mmc/host/sdhci-of-arasan.c:860:9: warning: variable 'ret' is
uninitialized when used here [-Wuninitialized]
return ret;
^~~
drivers/mmc/host/sdhci-of-arasan.c:810:9: note: initialize the variable
'ret' to silence this warning
int ret;
^
= 0
2 warnings generated.
This looks like a copy paste error. Neither function has handling that
needs ret so just remove it and return 0 directly.
Link: https://github.com/ClangBuiltLinux/linux/issues/996
Reported-by: kernelci.org bot <bot@kernelci.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20200416182402.16858-1-natechancellor@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the SDHCI specification, the Capabilities Register (Offset 0x40h)
is the 64-bit width register, but in Linux, it is represented as two
registers, SDHCI_CAPABILITIES and SDHCI_CAPABILITIES_1 so that drivers
can use 32-bit register accessors.
The upper 32-bit field is associated with SDHCI_CAPABILITIES_1.
Move the definition of SDHCI_CAPABILITIES_1 to the correct place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200408072105.422-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The data structure member “rpmb->md” was passed to a call of the function
“mmc_blk_put” after a call of the function “put_device”. Reorder these
function calls to keep the data accesses consistent.
Fixes: 1c87f73578 ("mmc: block: Fix bug when removing RPMB chardev ")
Signed-off-by: Peng Hao <richard.peng@oppo.com>
Cc: stable@vger.kernel.org
[Uffe: Fixed up mangled patch and updated commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
First, it should be noted that the CQE timeout (60 seconds) is substantial
so a CQE request that times out is really stuck, and the race between
timeout and completion is extremely unlikely. Nevertheless this patch
fixes an issue with it.
Commit ad73d6fead ("mmc: complete requests from ->timeout")
preserved the existing functionality, to complete the request.
However that had only been necessary because the block layer
timeout handler had been marking the request to prevent it from being
completed normally. That restriction was removed at the same time, the
result being that a request that has gone will have been completed anyway.
That is, the completion was unnecessary.
At the time, the unnecessary completion was harmless because the block
layer would ignore it, although that changed in kernel v5.0.
Note for stable, this patch will not apply cleanly without patch "mmc:
core: Fix recursive locking issue in CQE recovery path"
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: ad73d6fead ("mmc: complete requests from ->timeout")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200508062227.23144-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Consider the following stack trace
-001|raw_spin_lock_irqsave
-002|mmc_blk_cqe_complete_rq
-003|__blk_mq_complete_request(inline)
-003|blk_mq_complete_request(rq)
-004|mmc_cqe_timed_out(inline)
-004|mmc_mq_timed_out
mmc_mq_timed_out acquires the queue_lock for the first
time. The mmc_blk_cqe_complete_rq function also tries to acquire
the same queue lock resulting in recursive locking where the task
is spinning for the same lock which it has already acquired leading
to watchdog bark.
Fix this issue with the lock only for the required critical section.
Cc: <stable@vger.kernel.org>
Fixes: 1e8e55b670 ("mmc: block: Add CQE support")
Suggested-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1588868135-31783-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the request completion path with CQE, request type is being checked
after the request is getting completed. This is resulting in returning
the wrong request type and leading to the IO hang issue.
ASYNC request type is getting returned for DCMD type requests.
Because of this mismatch, mq->cqe_busy flag is never getting cleared
and the driver is not invoking blk_mq_hw_run_queue. So requests are not
getting dispatched to the LLD from the block layer.
All these eventually leading to IO hang issues.
So, get the request type before completing the request.
Cc: <stable@vger.kernel.org>
Fixes: 1e8e55b670 ("mmc: block: Add CQE support")
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1588775643-18037-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Making COMMON_CLK a visible option causes the sparc allyesconfig to fail
to build like so:
sparc64-linux-ld: drivers/mmc/host/meson-mx-sdio.o: in function `meson_mx_mmc_remove':
meson-mx-sdio.c:(.text+0x70): undefined reference to `of_platform_device_destroy'
sparc64-linux-ld: drivers/mmc/host/meson-mx-sdio.o: in function `meson_mx_mmc_probe':
meson-mx-sdio.c:(.text+0x9e4): undefined reference to `of_platform_device_create'
sparc64-linux-ld: meson-mx-sdio.c:(.text+0xdd4): undefined reference to `of_platform_device_destroy'
This is because the implementation of of_platform_device_destroy() is
inside an #ifdef CONFIG_OF_ADDRESS section of drivers/of/platform.c.
This driver already depends on OF being enabled, so let's tighten that
constrain a little more so that it depends on OF_ADDRESS instead. This
way we won't try to build this driver on platforms that don't have this
function.
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200409064416.83340-7-sboyd@kernel.org
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
BIOS writers have begun the practice of setting 40 ohm eMMC driver strength
even though the eMMC may not support it, on the assumption that the kernel
will validate the value against the eMMC (Extended CSD DRIVER_STRENGTH
[offset 197]) and revert to the default 50 ohm value if 40 ohm is invalid.
This is done to avoid changing the value for different boards.
Putting aside the merits of this approach, it is clear the eMMC's mask
of supported driver strengths is more reliable than the value provided
by BIOS. Add validation accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 51ced59cc0 ("mmc: sdhci-pci: Use ACPI DSM to get driver strength for some Intel devices")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200422111629.4899-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For some reason the Host Control2 register of the Xenon SDHCI controller
sometimes reports the bit representing 1.8V signaling as 0 when read
after it was written as 1. Subsequent read reports 1.
This causes the sdhci_start_signal_voltage_switch function to report
1.8V regulator output did not become stable
When CONFIG_PM is enabled, the host is suspended and resumend many
times, and in each resume the switch to 1.8V is called, and so the
kernel log reports this message annoyingly often.
Do an empty read of the Host Control2 register in Xenon's
.voltage_switch method to circumvent this.
This patch fixes this particular problem on Turris MOX.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: 8d876bf472 ("mmc: sdhci-xenon: wait 5ms after set 1.8V...")
Cc: stable@vger.kernel.org # v4.16+
Link: https://lore.kernel.org/r/20200420080444.25242-1-marek.behun@nic.cz
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MSM sd host controller is capable of HW busy detection of device busy
signaling over DAT0 line. And it requires the R1B response for commands
that have this response associated with them.
So set the below two host capabilities for qcom SDHC.
- MMC_CAP_WAIT_WHILE_BUSY
- MMC_CAP_NEED_RSP_BUSY
Recent development of the mmc core in regards to this, revealed this as
being a potential bug, hence the stable tag.
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1587363626-20413-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Open-coding a timeout loop invariably leads to errors with handling
the timeout properly in one corner case or another. In the case of
cqhci we might report "CQE stuck on" even if it wasn't stuck on.
You'd just need this sequence of events to happen in cqhci_off():
1. Call ktime_get().
2. Something happens to interrupt the CPU for > 100 us (context switch
or interrupt).
3. Check time and; set "timed_out" to true since > 100 us.
4. Read CQHCI_CTL.
5. Both "reg & CQHCI_HALT" and "timed_out" are true, so break.
6. Since "timed_out" is true, falsely print the error message.
Rather than fixing the polling loop, use readx_poll_timeout() like
many people do. This has been time tested to handle the corner cases.
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200413162717.1.Idece266f5c8793193b57a1ddb1066d030c6af8e0@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The recent commit 0d84c3e6a5 ("mmc: core: Convert to
mmc_poll_for_busy() for erase/trim/discard") makes use of the
->card_busy() op for SD cards. This uncovered that the ->card_busy() op
in the Meson SDIO driver was never working right:
while polling the busy status with ->card_busy()
meson_mx_mmc_card_busy() reads only one of the two MESON_MX_SDIO_IRQC
register values 0x1f001f10 or 0x1f003f10. This translates to "three out
of four DAT lines are HIGH" and "all four DAT lines are HIGH", which
is interpreted as "the card is busy".
It turns out that no situation can be observed where all four DAT lines
are LOW, meaning the card is not busy anymore. Upon further research the
3.10 vendor driver for this controller does not implement the
->card_busy() op.
Remove the ->card_busy() op from the meson-mx-sdio driver since it is
not working. At the time of writing this patch it is not clear what's
needed to make the ->card_busy() implementation work with this specific
controller hardware. For all use-cases which have previously worked the
MMC_CAP_WAIT_WHILE_BUSY flag is now taking over, even if we don't have
a ->card_busy() op anymore.
Fixes: ed80a13bb4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200416183513.993763-3-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
