Pull MMC updates from Ulf Hansson:
"MMC core:
- Add a new host cap bit and a corresponding DT property, to support
power cycling of the card by FW at system suspend/resume.
- Fix clock rate setting for SDIO in SDR12/SDR25 speed-mode
- Fix switch to 1/4-bit mode at system suspend/resume for SD-combo
cards
- Convert the mmc-pwrseq DT bindings to the json-schema
- Always allow the card detect uevent to be consumed by userspace
MMC host controllers:
- Convert a few DT bindings to the json-schema
- mtk-sd:
- Add support for command queue through cqhci
- Add support for the MT6779 variant
- renesas_sdhi_internal_dmac:
- Fix dma unmapping in the error path
- sdhci_am654:
- Add support for the AM65x PG2.0 variant
- Extend support for phys/clocks
- sdhci-cadence:
- Drop incorrect HW tuning for SD mode
- sdhci-msm:
- Add support for interconnect bandwidth scaling
- Enable internal voltage control
- Enable low power state for pinctrls
- sdhci-of-at91:
- Ludovic Desroches handovers maintenance to Eugen Hristev
- sdhci-pci-gli:
- Improve clock handling for GL975x
- sdhci-pci-o2micro:
- Add HW tuning for SDR104 mode
- Fix support for O2 host controller Seabird1"
* tag 'mmc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (66 commits)
mmc: mediatek: make function msdc_cqe_disable() static
MAINTAINERS: mmc: sdhci-of-at91: handover maintenance to Eugen Hristev
dt-bindings: mmc: mediatek: Add document for mt6779
mmc: mediatek: command queue support
mmc: mediatek: refine msdc timeout api
mmc: mediatek: add MT6779 MMC driver support
mmc: sdhci-pci-o2micro: Add HW tuning for SDR104 mode
mmc: sdhci-pci-o2micro: Bug fix for O2 host controller Seabird1
mmc: via-sdmmc: use generic power management
memstick: jmb38x_ms: use generic power management
mmc: sdhci-cadence: do not use hardware tuning for SD mode
mmc: sdhci-pci-gli: Set SDR104's clock to 205MHz and enable SSC for GL975x
mmc: cqhci: Fix a print format for the task descriptor
mmc: sdhci-of-arasan: fix timings allocation code
mmc: sdhci: Fix a potential uninitialized variable
dt-bindings: mmc: renesas,sdhi: convert to YAML
dt-bindings: mmc: convert arasan sdhci bindings to yaml
mmc: sdhci: Fix potential null pointer access while accessing vqmmc
mmc: core: Add MMC_CAP2_FULL_PWR_CYCLE_IN_SUSPEND
dt-bindings: mmc: Add full-pwr-cycle-in-suspend property
...
Smatch complains that "ret" can be used without being initialized.
drivers/mmc/host/sdhci.c
4383 if (!IS_ERR(mmc->supply.vqmmc)) {
4384 if (enable_vqmmc) {
^^^^^^^^^^^^
4385 ret = regulator_enable(mmc->supply.vqmmc);
^^^^^
4386 host->sdhci_core_to_disable_vqmmc = !ret;
4387 }
"ret" is only initialized when "enable_vqmmc" is true.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200714141410.GB314989@mwanda
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When use one SDIO wifi which enable the runtime PM feature on i.MX6SX,
we meet system hang. This hang happened during the usdhc runtime resume,
in sdhci_init(), when call the sdhci_set_default_irqs. One interrupt
(SDHCI_INT_CARD_INT) triggered just after the host->ier update and before
the write of register SDHCI_SIGNAL_ENABLE. So in sdhci_irq, it will skip
the call of sdio_signal_irq() because current host->ier do not set the
SDHCI_INT_CARD_INT. So this SDIO wifi interrupt always keep triggered,
let the system stuck in irq handle, can't response any other thread.
This patch add spin lock for the sdhci_set_default_irqs to fix this issue.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1586941255-9237-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Spending time under spinlock increases IRQ latencies and also
response times because preemption is disabled.
sdhci_send_command() waits up to 10 ms under spinlock for inhibit bits
to clear. In general inhibit bits will not be set, but there may be
corner cases, especially in the face of errors, where waiting helps.
There might also be dysfunctional hardware that needs the waiting. So
retain the legacy behaviour but do not wait for inhibit bits while under
spinlock. Instead adjust the logic to enable waiting while not under
spinlock. That is mostly straight forward, but in the interrupt handler
it requires deferring an "inhibited" command to the IRQ thread where
sleeping is allowed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-6-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Patch all drivers which use mmc_regulator_set_vqmmc() and prepare them for
the fact that mmc_regulator_set_vqmmc() can return a value > 0, which would
happen if the signal voltage switch did NOT happen, because the voltage was
already set correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200416163649.336967-1-marex@denx.de
[Ulf: Re-worked/simplified the code a bit]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When using the host software queue, it will trigger the next request in
irq handler without a context switch. But the sdhci_request() can not be
called in interrupt context when using host software queue for some host
drivers, due to the get_cd() ops can be sleepable.
But for some host drivers, such as Spreadtrum host driver, the card is
nonremovable, so the get_cd() ops is not sleepable, which means we can
complete the data request and trigger the next request in irq handler
to remove the context switch for the Spreadtrum host driver.
As suggested by Adrian, we should introduce a request_atomic() API to
indicate that a request can be called in interrupt context to remove
the context switch when using mmc host software queue. But this should
be done in another thread to convert the users of mmc host software queue.
Thus we can introduce a variable in struct sdhci_host to indicate that
we will always to defer to complete requests when using the host software
queue.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/e693e7a29beb3c1922b333f4603ea81f43d5c5b1.1581478568.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let a vendor driver supply the maximum descriptor size that it
can operate on. ADMA descriptor table would be allocated using this
supplied size.
If any SD Host controller is of version prior to v4.10 spec
but supports 16byte descriptor, this change allows them to supply
correct descriptor size for ADMA table allocation.
Also let a vendor driver update the descriptor size by overriding
sdhc_host->desc_size if it has to operates on a different descriptor
sizes in different conditions.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1579531122-28341-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some standard SD host controllers can support both external dma
controllers as well as ADMA/SDMA in which the SD host controller
acts as DMA master. TI's omap controller is the case as an example.
Currently the generic SDHCI code supports ADMA/SDMA integrated in
the host controller but does not have any support for external DMA
controllers implemented using dmaengine, meaning that custom code is
needed for any systems that use an external DMA controller with SDHCI.
Fixes by Faiz Abbas <faiz_abbas@ti.com>:
1. Map scatterlists before dmaengine_prep_slave_sg()
2. Use dma_async() functions inside of the send_command() path and call
terminate_sync() in non-atomic context in case of an error.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-4-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tuning support in DDR50 speed mode was added in SD Specifications Part1
Physical Layer Specification v3.01. Its not possible to distinguish
between v3.00 and v3.01 from the SCR and that is why since
commit 4324f6de6d ("mmc: core: enable CMD19 tuning for DDR50 mode")
tuning failures are ignored in DDR50 speed mode.
Cards compatible with v3.00 don't respond to CMD19 in DDR50 and this
error gets printed during enumeration and also if retune is triggered at
any time during operation. Update the printk level to pr_debug so that
these errors don't lead to false error reports.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: stable@vger.kernel.org # v4.4+
Link: https://lore.kernel.org/r/20191206114326.15856-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tuning support in DDR50 speed mode was added in SD Specifications Part1
Physical Layer Specification v3.01. Its not possible to distinguish
between v3.00 and v3.01 from the SCR and that is why since
commit 4324f6de6d ("mmc: core: enable CMD19 tuning for DDR50 mode")
tuning failures are ignored in DDR50 speed mode.
Cards compatible with v3.00 don't respond to CMD19 in DDR50 and this
error gets printed during enumeration and also if retune is triggered at
any time during operation. Update the printk level to pr_debug so that
these errors don't lead to false error reports.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: stable@vger.kernel.org # v4.4+
Link: https://lore.kernel.org/r/20191206114326.15856-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In sdhci_do_reset we call the reset callback which is typically
sdhci_reset. sdhci_reset can wait for up to 100ms waiting for the
controller to reset. If SDHCI_RESET_ALL was passed as the flag, the
controller will clear the IRQ mask. If during that 100ms the card is
removed there is no notification to the MMC system that the card was
removed. So from the drivers point of view the card is always present.
By making sdhci_reinit compare the present state it can schedule a
rescan if the card was removed while a reset was in progress.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ADMA errors are potentially data corrupting events; although we print
the register state, we do not usefully print the ADMA descriptors.
Worse than that, we print them by referencing their virtual address
which is meaningless when the register state gives us the DMA address
of the failing descriptor.
Print the ADMA descriptors giving their DMA addresses rather than their
virtual addresses, and print them using SDHCI_DUMP() rather than DBG().
We also do not show the correct value of the interrupt status register;
the register dump shows the current value, after we have cleared the
pending interrupts we are going to service. What is more useful is to
print the interrupts that _were_ pending at the time the ADMA error was
encountered. Fix that too.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of keeping track of whether SDIO IRQs have been enabled via an
internal sdhci status flag, avoid the open-coding and convert into using
sdio_irq_claimed().
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Nowadays sdhci prevents runtime suspend when SDIO IRQs are enabled.
However, some variants such as sdhci-esdhc-imx's, tries to allow runtime
suspend while having the SDIO IRQs enabled, but without supporting remote
wakeups. This support is a bit questionable, especially if the host device
have a PM domain attached that can be power gated, but more importantly,
the code have also become redundant (which was not the case when it was
introduced).
Rather than keeping the redundant code around, let's drop it and leave this
to be revisited later on.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_ack_sdio_irq() is called only when SDIO IRQs are enabled.
Therefore, let's drop the redundant check of the internal
SDHCI_SDIO_IRQ_ENABLED flag and just re-enable the IRQs immediately.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When switching from any MMC speed mode that requires 1.8v
(HS200, HS400 and HS400ES) to High Speed (HS) mode, the system
ends up configured for SDR12 with a 50MHz clock which is an illegal
mode.
This happens because the SDHCI_CTRL_VDD_180 bit in the
SDHCI_HOST_CONTROL2 register is left set and when this bit is
set, the speed mode is controlled by the SDHCI_CTRL_UHS field
in the SDHCI_HOST_CONTROL2 register. The SDHCI_CTRL_UHS field
will end up being set to 0 (SDR12) by sdhci_set_uhs_signaling()
because there is no UHS mode being set.
The fix is to change sdhci_set_uhs_signaling() to set the
SDHCI_CTRL_UHS field to SDR25 (which is the same as HS) for
any switch to HS mode.
This was found on a new eMMC controller that does strict checking
of the speed mode and the corresponding clock rate. It caused the
switch to HS400 mode to fail because part of the sequence to switch
to HS400 requires a switch from HS200 to HS before going to HS400.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, the DMA addresses are casted to (u64) for the upper 32bits
to avoid "right shift count >= width of type" warning.
<linux/kernel.h> provides macros to address this, and I like the macro
names are self-documenting.
I introduced a new helper, sdhci_set_adma_addr() to avoid the code
duplication.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
__sdhci_read_caps() does not modify *ver, *caps, or *caps1.
Probably, the caller of this function will want to constifythe
parameters passed in.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
