Pull MIPS upates from Thomas Bogendoerfer:
- improvements for Loongson64
- extended ingenic support
- removal of not maintained paravirt system type
- cleanups and fixes
* tag 'mips_5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (81 commits)
MIPS: SGI-IP27: always enable NUMA in Kconfig
MAINTAINERS: Update KVM/MIPS maintainers
MIPS: Update default config file for Loongson-3
MIPS: KVM: Add kvm guest support for Loongson-3
dt-bindings: mips: Document Loongson kvm guest board
MIPS: handle Loongson-specific GSExc exception
MIPS: add definitions for Loongson-specific CP0.Diag1 register
MIPS: only register FTLBPar exception handler for supported models
MIPS: ingenic: Hardcode mem size for qi,lb60 board
MIPS: DTS: ingenic/qi,lb60: Add model and memory node
MIPS: ingenic: Use fw_passed_dtb even if CONFIG_BUILTIN_DTB
MIPS: head.S: Init fw_passed_dtb to builtin DTB
of: address: Fix parser address/size cells initialization
of_address: Guard of_bus_pci_get_flags with CONFIG_PCI
MIPS: DTS: Fix number of msi vectors for Loongson64G
MIPS: Loongson64: Add ISA node for LS7A PCH
MIPS: Loongson64: DTS: Fix ISA and PCI I/O ranges for RS780E PCH
MIPS: Loongson64: Enlarge IO_SPACE_LIMIT
MIPS: Loongson64: Process ISA Node in DeviceTree
of_address: Add bus type match for pci ranges parser
...
Add a memory node, which was missing until now, and use the retail name
"Ben Nanonote" as the model, as it is way more known under that name
than under the name "LB60".
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The ROUT (right channel output of audio codec) was connected to INL
(left channel of audio amplifier) instead of INR (right channel of audio
amplifier).
Fixes: 8ddebad15e ("MIPS: qi_lb60: Migrate to devicetree")
Cc: stable@vger.kernel.org # v5.3
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add a devicetree node for the Image Processing Unit (IPU) found in the
JZ4725B. Connect it with graph nodes to the LCD node. The LCD driver
will expect the IPU node to be accessed through graph port #8, as stated
in the bindings documentation.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
1.The CU1000-Neo board actually uses X1000E instead of X1000,
so the wrongly written "ingenic,x1000" in compatible should
be changed to "ingenic,x1000e".
2.Adjust the order of nodes according to the corresponding
address value.
3.Drop unnecessary node in "wlan_pwrseq".
4.Add the leds node to "cu1000-neo.dts".
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Support the Ingenic X1830 SoC using the code under arch/mips/jz4740.
This is left unselectable in Kconfig until a X1830 based board is
added in a later commit.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The RS-90, better known as RetroMini, is a small and pocketable handheld
gaming console from YLMChina. It has little more than a JZ4725B SoC, a
NAND, a screen, some buttons and a speaker.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add preliminary support for boards based on the JZ4725B SoC from
Ingenic.
The JZ4725B SoC is supposed to be older than the JZ4740 SoC, but its
internals are much closer to what can be found on the JZ4750 and newer
SoCs.
It is low-power SoC with a MIPS32r1 SoC running at ~360 MHz, and no FPU.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add support for the GCW Zero prototype. The only (?) difference is that
it only has 256 MiB of RAM, compared to the 512 MiB of RAM of the retail
device.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add memory info of the GCW Zero in its devicetree. The bootloader
generally provides this information, but since it is fixed to 512 MiB,
it doesn't hurt to have it in devicetree. It allows the kernel to boot
without any parameter passed as argument.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add support for the face buttons, the ACT8600 PMUC, the LCD panel
with backlight, the rumble, internal/external SD readers, and other
things.
Note that the otg-phy node was dropped in the process as it was neither
useful nor used, and was inside a non-compliant board "bus".
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add support for the RTC, AIC, CODEC, MMC 0/1/2, ADC, GPU, LCD,
USB OTG, USB PHY controllers.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add the TCU nodes to the JZ4780, JZ4770 and JZ4740 devicetree files.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
If N fields of X cells should be provided, then that's what the
devicetree should represent, instead of having one single field of
(N*X) cells.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The driver requires two cells and not just one.
Since these nodes are both disabled as no hardware currently use them,
this fix does not really requires a Fixes: tag.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
There is a unique MAC address programmed into the eFuses
of the JZ4780 chip in the CI20 factory. By using this
for initializing the DM9000 Ethernet controller, every
CI20 board has an individual - but stable - MAC address
and DHCP can assign stable IP addresses.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This patch brings support for the JZ4780 efuse. Currently it only exposes
a read only access to the entire 8K bits efuse memory and the
ethernet mac address for the davicom dm9000 chip on the CI20 board.
It also changes the nemc ranges definition to give the driver
access to the efuse registers, which are in the middle of the
nemc reg range.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
a) add DT node for SW1 as Enter button
The SW1 button can be used as a simple one-button keyboard
and is connected to PD17.
Note: SW1 has a second meaning to change the boot sequence
when pressed while powering on.
b) give eth0_power a defined voltage.
This is a 3.3V power switch (DVNET3.3V).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The infrared sensor on the CI20 board is connected to a GPIO and can
be operated by using the gpio-ir-recv driver. Add a DT node for the
sensor to allow that driver to be used.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
There is a ACT8600 on the CI20 board and the bindings of the
ACT8865 driver have changed without updating the CI20 device
tree. Therefore the PMU can not be probed successfully and
is running in power-on reset state.
Fix DT to match the latest act8865-regulator bindings.
Fixes: 73f2b94047 ("MIPS: CI20: DTS: Add I2C nodes")
Cc: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Merge the Ingenic TCU patchset from the ingenic-tcu-v5.4 branch which
was created to enable follow-on changes in other subsystems.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Move all the platform data to devicetree.
The only bit dropped is the PWM beeper, which requires the PWM driver
to be updated. I figured it's okay to remove it here since it's really
a non-critical device, and it'll be re-introduced soon enough.
The other change is the CS line of the SPI is now set as active low. The
SPI core would have forced "active low" anyway, unless the 'spi-cs-high'
property is set.
In the process of moving to devicetree, we also switched to new drivers:
- We use the simple-audio-card and simple-amplifier drivers instead of
the custom ASoC code;
- We use the new Ingenic DRM driver coupled with the GiantPlus GPM940B0
DRM panel driver instead of the old framebuffer driver;
- We use the new jz4780-dma driver instead of the old jz4740-dma one;
- We use the ingenic-nand and jz4740-ecc drivers instead of the old
jz4740-nand driver;
- We use ingenic-battery instead of jz4740-battery;
- We use iio-hwmon instead of jz4740-hwmon;
- We use ingenic-iio instead of the old jz4740-adc MFD driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
[paul.burton@mips.com:
Drop the unused & undocumented ili8960 spi@0 node.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Move the MMC configuration from the board C file to devicetree.
The 'power' GPIO was removed and instead the vmmc regulator is used,
to follow the changes introduced in the jz4740-mmc driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Add the devicetree nodes for the DMA core of the JZ4740 SoC, disabled
by default, as currently there are no clients for the DMA driver
(until the MMC driver and/or others get a devicetree node).
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the two devicetree nodes for the two DMA cores of the JZ4770 SoC,
disabled by default, as currently there are no clients for the DMA
driver (until the MMC driver and/or others get a devicetree node).
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver now accepts two memory resources, the first one for the
channel-specific registers, the second one for the controller-specific
registers.
Note that older devicetrees, without this commit, will still work with
the jz4780-dma driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull MIPS updates from James Hogan:
"These are the main MIPS changes for 4.18.
Rough overview:
- MAINTAINERS: Add Paul Burton as MIPS co-maintainer
- Misc: Generic compiler intrinsics, Y2038 improvements, Perf+MT fixes
- Platform support: Netgear WNR1000 V3, Microsemi Ocelot integrated
switch, Ingenic watchdog cleanups
More detailed summary:
Maintainers:
- Add Paul Burton as MIPS co-maintainer, as I soon won't have access
to much MIPS hardware, nor enough time to properly maintain MIPS on
my own.
Miscellaneous:
- Use generic GCC library routines from lib/
- Add notrace to generic ucmpdi2 implementation
- Rename compiler intrinsic selects to GENERIC_LIB_*
- vmlinuz: Use generic ashldi3
- y2038: Convert update/read_persistent_clock() to *_clock64()
- sni: Remove read_persistent_clock()
- perf: Fix perf with MT counting other threads
- Probe for per-TC perf counters in cpu-probe.c
- Use correct VPE ID for VPE tracing
Minor cleanups:
- Avoid unneeded built-in.a in DTS dirs
- sc-debugfs: Re-use kstrtobool_from_user
- memset.S: Reinstate delay slot indentation
- VPE: Fix spelling "uneeded" -> "Unneeded"
Platform support:
BCM47xx:
- Add support for Netgear WNR1000 V3
- firmware: Support small NVRAM partitions
- Use __initdata for LEDs platform data
Ingenic:
- Watchdog driver & platform code improvements:
- Disable clock after stopping counter
- Use devm_* functions
- Drop module remove function
- Move platform reset code to restart handler in driver
- JZ4740: Convert watchdog instantiation to DT
- JZ4780: Fix watchdog DT node
- qi_lb60_defconfig: Enable watchdog driver
Microsemi:
- Ocelot: Add support for integrated switch
- pcb123: Connect phys to ports"
* tag 'mips_4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (30 commits)
MAINTAINERS: Add Paul Burton as MIPS co-maintainer
MIPS: ptrace: Make FPU context layout comments match reality
MIPS: memset.S: Reinstate delay slot indentation
MIPS: perf: Fix perf with MT counting other threads
MIPS: perf: Use correct VPE ID when setting up VPE tracing
MIPS: perf: More robustly probe for the presence of per-tc counters
MIPS: Probe for MIPS MT perf counters per TC
MIPS: mscc: Connect phys to ports on ocelot_pcb123
MIPS: mscc: Add switch to ocelot
MIPS: JZ4740: Drop old platform reset code
MIPS: qi_lb60: Enable the jz4740-wdt driver
MIPS: JZ4780: dts: Fix watchdog node
MIPS: JZ4740: dts: Add bindings for the jz4740-wdt driver
watchdog: JZ4740: Drop module remove function
watchdog: JZ4740: Register a restart handler
watchdog: JZ4740: Use devm_* functions
watchdog: JZ4740: Disable clock after stopping counter
MIPS: VPE: Fix spelling mistake: "uneeded" -> "unneeded"
MIPS: Re-use kstrtobool_from_user()
MIPS: Convert update_persistent_clock() to update_persistent_clock64()
...
