PLL_SELFREQDCO bitfield is from bit 3 to 1, but the driver writes bits
from 4 to 1. The bit 4 is 'reserved', so this probably should not cause
any issues, but it's better to fix it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Preload register is dumped twice for video overlays and mflag register
is not dumped for GFX.
Fix the register dump.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
HDMI PLL's REGSD field is only set by the driver if the PLL's output
clock is over 1GHz. This is clearly an error, as REGSD should be set
always.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The PLL settings are committed by setting GO bit, which is then cleared
by the HW when the settings have been taken into use.
The current PLL code handles this wrong: instead of waiting for the bit
to be cleared, it waits for the bit to be set. Usually, the bit is
always set, as the CPU has just set it before. However, if the CPU takes
enough time between setting the GO bit and checking it, the HW may
already have cleared the bit and this leads to timeout error.
Fix the wait to check the bit properly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapfb disables all the overlays when freeing resources, but it should
also remove those overlays from overlay managers.
Not doing so causes a crash if omapfb is unbound and bound, or omapfb
module is removed and loaded, while keeping omapdss around.
Fix this by calling unset_manager() for all overlays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When omapfb is shutting down, it will disable all the overlays. However,
instead of actually disabling all the overlays, it disables only all the
overlays that are currently attached to framebuffers.
On OMAP4+, this leaves the fourth overlay left enabled.
Fix the loop so that we actually go through all the overlays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We should wait for any pending updates when an overlay manager is
about to be disabled, because the updates will never be finished if the
manager is disabled too early.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If we leave __exit annotation, driver can't be unbound
through sysfs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss drivers cannot handle devices being unbound while the devices
are part of a connected display pipeline. Module refcounts are used to
prevent unloading the modules, but one can still manually unbind the
devices via sysfs, causing crash.
Set suppress_bind_attrs to disable the bind/unbind support via sysfs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
without MODULE_ALIAS(), omapfb won't get loaded
automatically.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Replace the use of nested functions where a normal function will suffice.
Nested functions are not liked by upstream kernel developers in general. Their
use breaks the use of clang as a compiler, and doesn't make the code any
better.
This code now works for both gcc and clang.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Replace the use of nested functions where a normal function will suffice.
Nested functions are not liked by upstream kernel developers in general. Their
use breaks the use of clang as a compiler, and doesn't make the code any
better.
This code now works for both gcc and clang.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use c99 initializers for structures.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@decl@
identifier i1,fld;
type T;
field list[n] fs;
@@
struct i1 {
fs
T fld;
...};
@bad@
identifier decl.i1,i2;
expression e;
initializer list[decl.n] is;
@@
struct i1 i2 = { is,
+ .fld = e
- e
,...};
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Pull fbdev updates from Tomi Valkeinen:
- much better HDMI infoframe support for OMAP
- Cirrus Logic CLPS711X framebuffer driver
- DT support for PL11x CLCD driver
- various small fixes
* tag 'fbdev-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (35 commits)
OMAPDSS: DSI: fix depopulating dsi peripherals
video: hyperv: hyperv_fb: refresh the VM screen by force on VM panic
video: ARM CLCD: Fix DT-related build problems
drivers: video: fbdev: atmel_lcdfb.c: Add ability to inverted backlight PWM.
video: ARM CLCD: Add DT support
drm/omap: Add infoframe & dvi/hdmi mode support
OMAPDSS: HDMI: remove the unused code
OMAPDSS: HDMI5: add support to set infoframe & HDMI mode
OMAPDSS: HDMI4: add support to set infoframe & HDMI mode
OMAPDSS: HDMI: add infoframe and hdmi_dvi_mode fields
OMAPDSS: add hdmi ops to hdmi-connector and tpd12s015
OMAPDSS: add hdmi ops to hdmi_ops and omap_dss_driver
OMAPDSS: HDMI: remove custom avi infoframe
OMAPDSS: HDMI5: use common AVI infoframe support
OMAPDSS: HDMI4: use common AVI infoframe support
OMAPDSS: Kconfig: select HDMI
OMAPDSS: HDMI: fix name conflict
OMAPDSS: DISPC: clean up dispc_mgr_timings_ok
OMAPDSS: DISPC: reject interlace for lcd out
OMAPDSS: DISPC: fix debugfs reg dump
...
After v3.16-rc1, devices populated with of_platform_populate() should be
depopulated using of_platform_depopulate(). Failure to do so prevents
the devices from being populated again (e.g. when loading a module).
This patch fixes the problem for the OMAP DSI driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We no longer need the horrible driver internal videmode tables, which
were used to decide if a given videomode is a HDMI or DVI mode. So
remove all related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of using hardcoded AVI infoframe, and a custom HDMI/DVI mode
selection based in internal videomode tables, add support to set the
infoframe and HDMI/DVI mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of using hardcoded AVI infoframe, and a custom HDMI/DVI mode
selection based in internal videomode tables, add support to set the
infoframe and HDMI/DVI mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add infoframe and hdmi_dvi_mode fields to 'struct hdmi_config' which
will be used in the following patches for OMAP4 and OMAP5 HDMI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add pass-through functions for set_infoframe and set_hdmi_mode to
hdmi-connector and tpd12s015 drivers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We now use the common AVI infoframe support, so the OMAP specific AVI
infoframe code can be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of using OMAP specific AVI infoframe structs, use the common one
from include/linux/hdmi.h.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of using OMAP specific AVI infoframe structs, use the common one
from include/linux/hdmi.h.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP HDMI driver has an 'enum hdmi_audio_sample_size', which conflicts
with the common include/linux/hdmi.h.
Change the name of the OMAP specific enum with '_omap" postfix.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_mgr_timings_ok() is a bit confusing how it handles the return
value.
Change the function to just return immediately when a timing is deemed
not valid, making the code much easier to follow.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP2/3 does not support interlace for LCD out. OMAP4+ does, but is not
supported by the driver at the moment.
The driver still accepts interlaced mode for LCD out, causing broken
display output.
This patch makes dispc reject interlace for LCD out.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
kmalloc can return null. Add a check to avoid potential null
pointer dereference error when the pointer is accessed later.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
After a variable is assigned the result of backlight_device_register, an
error test should be performed before a dereference.
A simplified version of the semantic match that finds this problem is
as follows:
// <smpl>
@def0@
expression x;
position p0;
@@
x@p0 = backlight_device_register(...)
@protected@
expression def0.x,E;
position def0.p0;
position p;
statement S;
@@
x@p0
... when != x = E
if (!IS_ERR(x) && ...) {<... x@p ...>} else S
@unprotected@
expression def0.x,E;
identifier fld;
position def0.p0;
position p != protected.p;
@@
x@p0
... when != x = E
* x@p->fld
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move the panel/encoder driver compatible-string converter from
arch/arm/mach-omap2/display.c to omapdss driver. That is a more logical
place for it, as it's really an omapdss internal hack.
The code is rewritten to follow the video node graph, starting from
omapdss. This removes the need to have the device compatible-string
database.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit 59b3d38a36 missed cleaning up the
hdmi_wp.c file.
Clean up hdmi_wp.c the same way as the others.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We don't have any working boards using this panel right now, and the
panel driver looks odd compared to the panel specs. For example, the
panel spec does not mention any QVGA pin.
So, while this patch adds DT support to the driver, it's not really
supported and there are not bindings documentation for the panel until
someone can verify how the panel actually works.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Erik Gilling <konkers@android.com>
Using gpiod will make it easier to add device tree support
for this panel in the following patches.
Note that all the GPIOs for this panel are optional, any
of the the GPIOs could be configured with external pulls
instead of GPIOs, so let's not error out if GPIOs are not
found to make the panel more generic.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add DT support for panel-lgphilips-lb035q02.
We disable the use of the backlight_gpio as it should be handled via
backlight framework with DT boots.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Florian Vaussard <florian.vaussard@epfl.ch>
The new gpiod API supports automatic handling of active-high/active-low
with DT. To make it possible to use that when booting with DT, change
the driver's handling of the enable GPIO to use gpiod.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The enable gpio should be optional, but the driver returns an error if
it doesn't get the gpio.
So change the driver to accept -ENOENT error.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
When omapdss writes to DISPC_POL_FREQ register, it always ORs the bits
with the current contents of the register, never clearing the old ones,
causing wrong signal polarity settings.
As we write all the bits in DISPC_POL_FREQ, we don't need to care about
the current contents of the register. So fix the issue by constructing
new register value from scratch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that all the boards using OMAP HDMI are using DT boot, we can remove
the hacks for getting the ioresources with non-DT boot.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This adds a new driver to omapdss for OMAP5 HDMI. However, the new
driver uses common HDMI files which are shared with OMAP4 HDMI driver.
OMAP5 HDMI has a different HDMI core IP compared to OMAP4, but has very
similar PLL and PHY IPs which can be handled with common code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a features struct to differentiate between the HDMI PLLs on OMAP4
and OMAP5. The OMAP5 PLL is more sensitive when it comes to locking. We
need to ensure that the DCO freq isn't too low for lower pixel clocks.
Modify the PLL computation slightly to ensure the HDMI PLL locks for lower
frequencies. This will be later replaced by a more complex computation
which makes sure all the PLL constraints are met.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
