The multiplication ratio for the PLL is required to be even due to the
use of a "by 2 pre-scaler". Currently we are likely to end up with an
odd multiplier even though there is an equivalent set of parameters with
an even multiplier.
For example, using the 324MHz bit rate with a reference clock of 24MHz
we end up with M = 27, N = 2 whereas the example in the PHY databook
gives M = 54, N = 4 for this bit rate and reference clock.
By walking down through the available multiplier instead of up we are
more likely to hit an even multiplier. With the above example we do now
get M = 54, N = 4 as given by the databook.
While doing this, change the loop limits to encode the actual limits on
the divisor, which are:
40MHz >= (pllref / N) >= 5MHz
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-18-john@metanate.com
These values are specified as constant time periods but the PHY
configuration is in terms of the current lane byte clock so using
constant values guarantees that the timings will be outside the
specification with some display configurations.
Derive the necessary configuration from the byte clock in order to
ensure that the PHY configuration is correct.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-17-john@metanate.com
Panel drivers may want to sent commands during the disable function, for
example MIPI_DCS_SET_DISPLAY_OFF before the video signal ends. In order
to send commands we need to write to registers, so pclk must be enabled.
While changing this, remove the unnecessary code after the panel
unprepare call which seems to be a workaround for a specific panel and
thus belongs in the panel driver.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224125506.21533-13-john@metanate.com
Misc fixes for the 4.11 merge window.
- vmwgfx drm_control node compat patch
- rockchip&zte fix
- compat32 support for dma-buf ioctl (cc: stable ofc, since this is a
massive fumble. oops)
* tag 'drm-misc-next-fixes-2017-02-27' of git://anongit.freedesktop.org/git/drm-misc:
dma-buf: add support for compat ioctl
drm/vmwgfx: Work around drm removal of control nodes
drm/rockchip: cdn-dp: Fix error handling
drm/rockchip: add extcon dependency for DP
drm: zte: fix static checker warning on variable 'fmt'
Backmerge the main pull request to sync up with all the newly landed
drivers. Otherwise we'll have chaos even before 4.12 started in
earnest.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The newly added DP driver links against the extcon core, which fails when
extcon is a module and this driver is not:
drivers/gpu/drm/rockchip/cdn-dp-core.o: In function `cdn_dp_get_port_lanes':
cdn-dp-core.c:(.text.cdn_dp_get_port_lanes+0x24): undefined reference to `extcon_get_state'
cdn-dp-core.c:(.text.cdn_dp_get_port_lanes+0x44): undefined reference to `extcon_get_property'
Let's make Kconfig enforce correct behavior with a dependency.
Fixes: 1a0f7ed3ab ("drm/rockchip: cdn-dp: add cdn DP support for rk3399")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170214213215.2888509-1-arnd@arndb.de
Rockchip DRM used the arm special API, arm_iommu_*(), to attach
iommu for ARM32 SoCs. This patch convert to common iommu API
so it would support ARM64 like RK3399.
Since previous patch added support for direct IOMMU address space
management, there is no need to use DMA API anymore and this patch wires
things to use the new method.
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
The API is not suitable for subsystems consisting of multiple devices
and requires severe hacks to use it. To mitigate this, this patch
implements allocation and address space management locally by using
helpers provided by DRM framework, like other DRM drivers do, e.g.
Tegra.
This patch should not introduce any functional changes until the driver
is made to attach subdevices into an IOMMU domain with the generic IOMMU
API, which will happen in following patch. Based heavily on GEM
implementation of Tegra DRM driver.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: rjan Eide <orjan.eide@arm.com>
fix warning:
drivers/gpu/drm/rockchip/cdn-dp-reg.c:632:24: warning:
'val[1]' may be used uninitialized in this function [-Wmaybe-uninitialized]
msa_misc = 2 * val[0] + 32 * val[1] +
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
rockchip CDN-DP support.
* 'drm-rockchip-next-2017-02-05' of https://github.com/markyzq/kernel-drm-rockchip:
drm/rockchip: cdn-dp: don't configure hardware in mode_set
drm/rockchip: cdn-dp: retry to check sink count
drm/rockchip: cdn-dp: Move mutex_init to probe
drm/rockchip: cdn-dp: do not use drm_helper_hpd_irq_event
drm/rockchip: cdn-dp: Do not run worker while suspended
drm/rockchip: cdn-dp: Load firmware if no monitor connected
drm/rockchip: cdn-dp: add cdn DP support for rk3399
drm/rockchip: return ERR_PTR instead of NULL
drm/rockchip: vop: make vop register setting take effect
With atomic modesetting the hardware will be powered off when the
mode_set function is called. We should configure the hardware in the
enable function.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Sometimes the Dock is disconnected, but cdn_dp_encoder_disable is not
triggered by DRM. For example, unplug the Dock in console mode, and
re-plug it again, the cdn_dp_event_work will try to get the sink count
of Dock, since the DP is still active. But the Dock has been powered
down, it need re-power on, and wait for a while until it is ready to
DPCD communication.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
The cdn_dp_pd_event_work is using drm_helper_hpd_irq_event to update the
connector status, this function is used to update all connectors of
drm_device. Therefore, the detect of other connector will be call, when
cdn_dp_pd_event_work is triggered, every time. It is not necessary, and
it may cause system crash. replace drm_helper_hpd_irq_event with
drm_kms_helper_hotplug_event, only update cdn-dp status.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
If the driver is in suspended mode, the dp block may be disabled, and
chip registers may not be accessible. Yet, the worker may be triggered
in this situation by an extcon event. If that happens, the following crash
will be seen.
cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] *ERROR* Enable dp failed -19
cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] Connected, not enabled. Enabling cdn
Bad mode in Error handler detected, code 0xbf000002 -- SError
CPU: 1 PID: 10357 Comm: kworker/1:2 Not tainted 4.4.21-05903-ge0514ea #1
Hardware name: Google Kevin (DT)
Workqueue: events cdn_dp_pd_event_work
task: ffffffc0cda67080 ti: ffffffc0b9b80000 task.ti: ffffffc0b9b80000
PC is at cdn_dp_clock_reset+0x30/0xa8
LR is at cdn_dp_enable+0x1e0/0x69c
...
Call trace:
[<ffffffc0005a7e24>] cdn_dp_pd_event_work+0x58/0x3f4
[<ffffffc0002397f0>] process_one_work+0x240/0x424
[<ffffffc00023a28c>] worker_thread+0x2fc/0x424
[<ffffffc00023f5fc>] kthread+0x10c/0x114
[<ffffffc000203dd0>] ret_from_fork+0x10/0x40
Problem is two-fold: The worker should not run while suspended, and the
suspend function should not call cdn_dp_disable() while the worker is
running.
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
If no monitor is connected, suspend/resume cycles result in firmware
load errors because the driver attempts to load the firmware while
the system is in suspend state. This results in a kernel warning and
traceback.
Loading the firmware during boot fixes the problem. Note that we can not
just call schedule_work conditionally in cdn_dp_pd_event() if the insertion
status changed. The problem would still be seen if a monitor is connected
for the first time during suspend.
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
