Neither the OHCI or EHCI bindings are using the phy-names property, so we
can just drop it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
In the current state, A33 NAND controllers use PIO during
transfers. Throughput can be increased thanks to the use of DMA
(mostly during reads, because of the ECC pipelining feature).
Besides the usual addition of DMA DT properties, because the A33
NAND DMA handling is different than for older SoCs, we must also
update the compatible which has recently been introduced for this
purpose.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The NAND controller node name should be nand-controller and not nand as we
used previously according to the devicetree specification. Let's fix our
DTs.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The USB OTG binding we have mandates to have a dr_mode property, yet not
all boards are setting it.
Since the generic otg binding states that the default mode should be the
OTG mode, let's use that one in our DTSI.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The NAND pinctrl nodes names don't follow the pattern we've used and
enforced for some time. Make sure they do.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Even though we shouldn't really have any external user of the clock
provided by the TCON, if clock-output-names is set, then #clock-cells must
be there as well.
Fix this.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As can be shown by the YAML schema now, the combination of GIC compatibles
we were using has never been an option.
Switch to the gic-400 variant, which is the more correct option.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A23 and A33 both have an I2C controller in the ARISC domain, that share
the same pins with the RSB bus.
Even if it's an unusual configuration, that device can be used to drive the
PMIC, so let's use it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Our display engine endpoints trigger some DTC warnings due to the fact that
we're having a single endpoint that doesn't need any reg property, and
since we don't have a reg property, we don't need the address-cells and
size-cells properties anymore.
Fix those
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Commit d027521497 ("ARM: dts: sun8i-a23-a33: Move NAND controller device
node to sort by address") moved the NAND controller node around, but
dropped the default muxing in the process.
Reintroduce it.
Fixes: d027521497 ("ARM: dts: sun8i-a23-a33: Move NAND controller device node to sort by address")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The display pipeline has the same structure, resources and connections
on both the A23 and A33. The differences include:
- compatible strings
- extra clock, reset control, and IO region for SAT in the backend
only found on the A33
- missing ch1 clock for the TCON
However, while the A23 has the TCON ch1 clock defined in the CCU, and
the channel 1 registers are available, it does not have any means to
use channel 1 due to a lack of downstream encoders, and the enable bit
for channel 1 is hard-wired to 0 (off).
As the MIPI DSI output device is not officially documented, and there
are no A23 reference devices to test it, it is not covered by this
patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The NAND controller device node was inserted into the wrong position,
probably due to a rebase or merge, as the file's structure does not
provide enough context for git to accurately match the previous device
node block.
Fixes: d7b843df13 ("ARM: dts: sun8i: add NAND controller node for A23/A33")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The RTC module on the A23 was claimed to be the same as on the A31, when
in fact it is not. The A31 does not have an RTC external clock output,
and its internal RC oscillator's average clock rate is not in the same
range. The A33's RTC is the same as the A23.
This patch fixes the compatible string and clock properties to conform
to the updated bindings. The register range is also fixed.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The I2C's and MMC0 controllers have only one muxing option in the SoC. In
such a case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The pin groups are supposed to be in alphabetical order, and they aren't.
Fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The simple-framebuffer nodes have a unit address, but no reg property which
generates a warning when compiling it with DTC.
Change the simple-framebuffer node names so that there is no warnings on
this anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The #address-cells and #size-cells are only relevant for nodes that have
childs with reg properties. Otherwise, DTC will emit a warning saying that
those properties are unnecessary.
Remove them when needed.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our main node for all the in-SoC controllers used to have a unit name. The
unit-name, in addition to being actually false, would not match any reg
property, which generates a warning.
Remove it in order to remove those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Using skeleton.dtsi will create a memory node that will generate a warning
in DTC. However, that node will be created by the bootloader, so we can
just remove it entirely in order to remove that warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
This adds a SRAM controller node for the A23 and A33, with support for
the C1 SRAM region that is shared between the Video Engine and the CPU.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Fixed the prefix and the compatibles]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We introduced a new compatible for the NMI or R_INTC interrupt
controller. This new compatible has the register region aligned
to the boundary listed in the SoC's memory map.
This patch converts the NMI/R_INTC node to using the new compatible,
and fixes up the register region and device node name.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pull ARM Device-tree updates from Olof Johansson:
"Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
Major new platforms:
- Gemini has been ported to DT, so a handful of "new" platforms moved
over from board files
- Rockchip RK3288 support for Tinkerboard and Phytec phyCORE-RK3288
SoM and RDK
- A bunch of embedded platforms, several Linksys platforms, Synology
DS116,
- Motorola Droid4 (really old OMAP-based phone) support is added.
Some refactorings, i.e. Allwinner H3/H5 support is commonalized.
And lots of smaller changes, cleanups, etc. See shortlog for more
description
We're adding ability to cross-include DT files between arm and arm64,
by creating appropriate links in the dt-include directory, and using
arm/ and arm64/ as include prefixes. This will avoid other local hacks
such as per-file links between the two arch trees (this broke for
external mirroring of DT contents). Now they can just provide their
own appropriate dt-include hierarcy per platform"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (349 commits)
ARM: dts: exynos: Use - instead of @ for DT OPP entries
arm: spear6xx: add DT description of the ADC on SPEAr600
arm: spear6xx: remove unneeded pinctrl properties in spear600-evb
arm: spear6xx: switch spear600-evb to the new flash partition DT binding
arm: spear6xx: fix spaces in spear600-evb.dts
arm: spear6xx: use node labels in spear600-evb.dts
arm: spear6xx: add labels to various nodes in spear600.dtsi
ARM: dts: vexpress: fix few unit address format warnings
ARM: dts: at91: sama5d3_xplained: not all ADC channels are available
ARM: dts: at91: sama5d3_xplained: fix ADC vref
ARM: dts: at91: add envelope detector mux to the Axentia TSE-850
ARM: dts: armada-38x: label USB and SATA nodes
ARM: dts: imx6q-utilite-pro: add hpd gpio
ARM: dts: imx6qp-sabresd: Set reg_arm regulator supply
ARM: dts: imx6qdl-sabresd: Set LDO regulator supply
ARM: dts: imx: add Gateworks Ventana GW5903 support
ARM: dts: i.MX25: add AIPS control registers
ARM: dts: imx7-colibri: add Carrier Board 3.3V/5V regulators
ARM: dts: imx7-colibri: remove 1.8V fixed regulator
ARM: dts: imx7-colibri: allow to disable Ethernet rail
...
All dts files for the sunxi platform have been switched to the generic
pinconf bindings. As a result, the sunxi specific pinctrl macros are
no longer used.
Remove the #include entry with the following command:
sed --follow-symlinks -i -e '/pinctrl\/sun4i-a10.h/D' \
arch/arm/boot/dts/sun?i*.*
arch/arm/boot/dts/sun9i-a80.dtsi was then edited to remove the extra
empty line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mali clock rate was improperly assumed to be 408MHz, while it was
really 384Mhz, 408MHz being the "extreme" frequency, and definitely not
stable.
Switch for the stable, correct frequency for the GPU.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pull "Allwinner DT changes for 4.11, part 2" from Maxime Ripard:
Support for the audio codec and Mali GPU for the A33
* tag 'sunxi-dt-for-4.11-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun8i: sinlinx: Enable audio nodes
ARM: dts: sun8i: parrot: Enable audio nodes
ARM: dts: sun8i: Add audio codec, dai and card for A33
ARM: sun8i: dt: Add mali node
dt-bindings: gpu: Add Mali Utgard bindings
Pull "Allwinner DT changes for 4.11" from Maxime Ripard:
The usual chunk of DT changes, most notably:
- Support for the H2+ and the V3s
- CPUFreq support for the A33
- SPDIF support for the A31 and H3
- New boards: Beelink X2, Lichee Pi One, Lichee Pi Zero,
Orange Pi Zero
* tag 'sunxi-dt-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (42 commits)
ARM: dts: sun8i-h3: Add SPDIF to the Beelink X2
ARM: dts: sun8i-h3: Add the SPDIF block to the H3
ARM: dts: sun8i-h3: Add SPDIF TX pin to the H3
ARM: dts: sun8i-h3: Add dts for the Beelink X2 STB
ARM: sun8i: sina33: Enable display
ARM: sun8i: a23/a33: Add the oscillators accuracy
ARM: sun8i: a23/a33: Enable the real LOSC and use it
ARM: dts: sunxi: add support for Lichee Pi Zero board
ARM: dts: sunxi: add dtsi file for V3s SoC
ARM: dts: sun6i: sina31s: Enable USB OTG controller in peripheral mode
ARM: dts: sun8i: reference-design: use AXP223 DTSI
ARM: dts: sun8i: parrot: use AXP223 DTSI
ARM: dts: sun8i: sina33: use AXP223 DTSI
ARM: dts: sun8i: a33-olinuxino: use AXP223 DTSI
ARM: dts: add DTSI for AXP223
dt-bindings: power: axp20x-usb: add axp223 compatible
ARM: dts: sun7i: Add wifi dt node on Banana Pro
ARM: dts: sun6i: Add SPDIF to the Mele I7
devicetree: bindings: Add vendor prefix for Shenzhen Xunlong Software
ARM: dts: sun8i-h3: orange-pi-pc: Enable audio codec
...
Since everybody copied my own mistake from the DT binding example,
let's address all the offenders in one swift go.
Most of them got the CPU interface size wrong (4kB, while it should
be 8kB), except for both keystone platforms which got the control
interface wrong (4kB instead of 8kB).
In a few cases where I knew for sure what implementation was used,
I've added the "arm,gic-400" compatible string. I'm 99% sure that
this is what everyone is using, but short of having the TRM for
all the other SoCs, I've left them alone.
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The A23 and A33 have an ARM Mali 400 GPU. Now that we have a binding, add
it to our DT.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The datasheet provided by Allwinner requires oscillators with an accuracy
of 50ppm. Add it to our fixed clocks so that we can properly track the
accuracy chain.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
So far, the LOSC was generated through the RTC internal oscillator, which
was a pretty poor and inaccurate choice.
Now that the RTC properly exposes its internal mux between its oscillator
and the external oscillator, we can use it were relevant.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A23/A33, the internal codec's analog path controls are located in
the PRCM node.
Add a sub-device node to the PRCM for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A "cpu0" label is needed on cpu@0 for cpufreq-dt to work.
Add such a label, in order to prepare for cpufreq support of A23/33.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In the past, all the MMC pins had
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
which was actually a no-op. We were relying on U-boot to set the bias
pull up for us. These properties were removed as part of the fix up to
actually support no bias on the pins. During the transition some boards
experienced regular MMC time-outs during normal operation, while others
completely failed to initialize the SD card.
Given that MMC starts in open-drain mode and the pull-ups are required,
it's best to enable it for all the pin settings.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The allwinner,pull property set to NO_PULL was really considered our
default (and wasn't even changing the default value in the code).
Remove these properties to make it obvious that we do not set anything in
such a case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The allwinner,drive property set to 10mA was really considered as our
default. Remove all those properties entirely to make that obvious.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
When the patch is applied, the allwinner,driver and allwinner,pull
properties are removed.
Although they're described to be optional in the devicetree binding,
without them, the pinmux cannot be initialized, and the uart cannot
be used.
Add them back to fix the problem, and makes the bluetooth on iNet D978
Rev2 board work.
Fixes: 82eec38424 (ARM: dts: sun8i: add pinmux for UART1 at PG)
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been merged
for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and usb
driver changes are required and included here, and also the clk
tree changes.
- The Allwinner platforms have seen a large-scale change to their clk
drivers and the dts file updates must come after that. This
includes the newly added Nextthing GR8 platform, which is derived
from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't added
until just before the merge window"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
ARM: dts: lpc32xx: add device node for IRAM on-chip memory
ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
ARM: dts: sun8i: add pinmux for UART1 at PG
dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
dts: sun8i-h3: add pinmux definitions for I2C0-2
dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
dts: sun8i-h3: add pinmux definitions for UART2-3
ARM: dts: sun9i: a80-optimus: Disable EHCI1
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
...
Pull ARM DT updates from Arnd Bergmann:
"These are as usual a very large number of mostly boring updates to
enable devices in existing machines, or to fix minor bugs. Notably, an
ongoing treewide effort to fix warnings caused by an update to the
device tree compiler. These are enabled with "make W=1" at the moment
but can hopefully become the default once all issues have been
addressed.
No new SoC platform is added this time around (Armada 395 and Orion
mv88f5181 are slight variations of existing ones), but a significant
number of new dts files are added, which I list by platform:
- Allwinner: Empire Electronix M712 and iNet d978 Rev2 tablets,
Orange Pi PC Plus, Orange Pi 2, Orange Pi Plus 2E, Orange Pi Lite,
Olimex A33-Olinuxino, and Nano Pi Neo single-board computers
- ARM Realview: all supported machines (ported from board files)
- Broadcom: BCM958525er, BCM958522er, BCM988312hr, BCM958623hr and
BCM958622hr reference boards for Northstar platform, Raspberry Pi
Zero single-board computer
- Marvell EBU: Netgear WNR854T router (ported from board file),
Armada 395 SoC platform and GP board Armada 390 DB development
board
- NXP i.MX: imx7s Warp7 reference board, Gateworks Ventana GW553x
single-board computer, Technologic Systems TS-4900 and Engicam
IMX6UL GEA M6UL computer-on-module, Inverse Path USB armory board
- Qualcomm: LG Nexus 5 Phone
- Renesas: r8a7792/wheat and r7s72100/rskrza1 development boards
- Rockchip: Rockchip RK3288 Fennec reference board, Firefly RK3288
Reload platform
- ST Microelectronics STi: B2260 (96boards) single-board computer
- TI Davinci: OMAP-L138 LCDK Development kit
- TI OMAP: beagleboard-x15 rev B1 single-board computer"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (390 commits)
ARM: dts: sony-nsz-gs7: add missing unit name to /memory node
ARM: dts: chromecast: add missing unit name to /memory node
ARM: dts: berlin2q-marvell-dmp: add missing unit name to /memory node
ARM: dts: berlin2: Add missing unit name to /soc node
ARM: dts: berlin2cd: Add missing unit name to /soc node
ARM: dts: berlin2q: Add missing unit name to /soc node
ARM: dts: berlin2: Remove skeleton.dtsi inclusion
ARM: dts: berlin2cd: Remove skeleton.dtsi inclusion
ARM: dts: berlin2q: Remove skeleton.dtsi inclusion
arm: dts: berlin2q: enable all wdt nodes unconditionally
arm: dts: berlin2: enable all wdt nodes unconditionally
ARM: dts: omap5-igep0050.dts: Use tabs for indentation
ARM: dts: Fix igepv5 power button GPIO direction
ARM: dts: am335x-evmsk: Add blue-and-red-wiring -property to lcdc node
ARM: dts: am335x-evmsk: Whitespace cleanup of lcdc related nodes
ARM: dts: am335x-evm: Add blue-and-red-wiring -property to lcdc node
ARM: dts: s3c64xx: Use macros for pinctrl configuration
ARM: dts: s3c2416: Use macros for pinctrl configuration
ARM: dts: s5pv210: Use macros for pinctrl configuration
ARM: dts: s3c64xx: Use common macros for pinctrl configuration
...
The UART1 at PG (PG6, PG7, PG8, PG9) is, in the Allwinner's reference
tablet design of A23/33, used to connect to UART Bluetooth cards.
Add the pinmux for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The usbphy and usb_otg nodes in the A23 and A33 dts files only differ
by compatible, and for the usbphy, the size of one of its register
regions.
Move all the common bits to the A23/A33 common dtsi file.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have support for the CCU driver in sunxi-ng, convert the A23
and A33 DTs to that driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
A23/A33 has a NAND controller which can now be used properly.
Add a device node for it.
The DMA function cannot work because of changed DMA IP block, so it's
temporarily removed in the device node. However, with PIO mode it can still
work.
Tested on an Aoson M751s tablet with Boris Brezillon's "mtd: nand: allow
vendor specific detection/initialization" patchset, which is needed for the
large-block MLC chip to be recognized correctly.
( http://lists.infradead.org/pipermail/linux-mtd/2016-June/068198.html )
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
