The NL_SET_ERR_MSG_MOD macro is used to report a string describing an
error message to userspace via the netlink extended ACK structure. It
should not have a trailing newline.
Add a cocci script which catches cases where the newline marker is
present. Using this script, fix the handful of cases which accidentally
included a trailing new line.
I couldn't figure out a way to get a patch mode working, so this script
only implements context, report, and org.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MCU CPSW expected to populate only MDIO device, but follow up patches
will add "compatible" property to the MCU CPSW CPTS node which will cause
creation of CPTS device and MCU CPSW init failure. Hence, switch to use
of_platform_device_create() instead of of_platform_populate() for MDIO
device population.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create an independent function that takes a particular frame queue and
an array of frame descriptors and tries to enqueue them until it hits
the maximum number fo retries. The same function will be used in the
next patch also on the XDP_TX path.
Also, create the dpaa2_eth_xdp_fds structure to incorporate the array of
FDs as well as the number of FDs already populated.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restrict the TTEthernet hardware support on this switch to operate as
closely as possible to IEEE 802.1Qci as possible. This means that it can
perform PTP-time-based ingress admission control on streams identified
by {DMAC, VID, PCP}, which is useful when trying to ensure the
determinism of traffic scheduled via IEEE 802.1Qbv.
The oddity comes from the fact that in hardware (and in TTEthernet at
large), virtual links always need a full-blown action, including not
only the type of policing, but also the list of destination ports. So in
practice, a single tc-gate action will result in all packets getting
dropped. Additional actions (either "trap" or "redirect") need to be
specified in the same filter rule such that the conforming packets are
actually forwarded somewhere.
Apart from the VL Lookup, Policing and Forwarding tables which need to
be programmed for each flow (virtual link), the Schedule engine also
needs to be told to open/close the admission gates for each individual
virtual link. A fairly accurate (and detailed) description of how that
works is already present in sja1105_tas.c, since it is already used to
trigger the egress gates for the tc-taprio offload (IEEE 802.1Qbv). Key
point here, we remember that the schedule engine supports 8
"subschedules" (execution threads that iterate through the global
schedule in parallel, and that no 2 hardware threads must execute a
schedule entry at the same time). For tc-taprio, each egress port used
one of these 8 subschedules, leaving a total of 4 subschedules unused.
In principle we could have allocated 1 subschedule for the tc-gate
offload of each ingress port, but actually the schedules of all virtual
links installed on each ingress port would have needed to be merged
together, before they could have been programmed to hardware. So
simplify our life and just merge the entire tc-gate configuration, for
all virtual links on all ingress ports, into a single subschedule. Be
sure to check that against the usual hardware scheduling conflicts, and
program it to hardware alongside any tc-taprio subschedule that may be
present.
The following scenarios were tested:
1. Quantitative testing:
tc qdisc add dev swp2 clsact
tc filter add dev swp2 ingress flower skip_sw \
dst_mac 42:be:24:9b:76:20 \
action gate index 1 base-time 0 \
sched-entry OPEN 1200 -1 -1 \
sched-entry CLOSE 1200 -1 -1 \
action trap
ping 192.168.1.2 -f
PING 192.168.1.2 (192.168.1.2) 56(84) bytes of data.
.............................
--- 192.168.1.2 ping statistics ---
948 packets transmitted, 467 received, 50.7384% packet loss, time 9671ms
2. Qualitative testing (with a phase-aligned schedule - the clocks are
synchronized by ptp4l, not shown here):
Receiver (sja1105):
tc qdisc add dev swp2 clsact
now=$(phc_ctl /dev/ptp1 get | awk '/clock time is/ {print $5}') && \
sec=$(echo $now | awk -F. '{print $1}') && \
base_time="$(((sec + 2) * 1000000000))" && \
echo "base time ${base_time}"
tc filter add dev swp2 ingress flower skip_sw \
dst_mac 42:be:24:9b:76:20 \
action gate base-time ${base_time} \
sched-entry OPEN 60000 -1 -1 \
sched-entry CLOSE 40000 -1 -1 \
action trap
Sender (enetc):
now=$(phc_ctl /dev/ptp0 get | awk '/clock time is/ {print $5}') && \
sec=$(echo $now | awk -F. '{print $1}') && \
base_time="$(((sec + 2) * 1000000000))" && \
echo "base time ${base_time}"
tc qdisc add dev eno0 parent root taprio \
num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time ${base_time} \
sched-entry S 01 50000 \
sched-entry S 00 50000 \
flags 2
ping -A 192.168.1.1
PING 192.168.1.1 (192.168.1.1): 56 data bytes
...
^C
--- 192.168.1.1 ping statistics ---
1425 packets transmitted, 1424 packets received, 0% packet loss
round-trip min/avg/max = 0.322/0.361/0.990 ms
And just for comparison, with the tc-taprio schedule deleted:
ping -A 192.168.1.1
PING 192.168.1.1 (192.168.1.1): 56 data bytes
...
^C
--- 192.168.1.1 ping statistics ---
33 packets transmitted, 19 packets received, 42% packet loss
round-trip min/avg/max = 0.336/0.464/0.597 ms
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement tc-flower offloads for redirect, trap and drop using
non-critical virtual links.
Commands which were tested to work are:
# Send frames received on swp2 with a DA of 42:be:24:9b:76:20 to the
# CPU and to swp3. This type of key (DA only) when the port's VLAN
# awareness state is off.
tc qdisc add dev swp2 clsact
tc filter add dev swp2 ingress flower skip_sw dst_mac 42:be:24:9b:76:20 \
action mirred egress redirect dev swp3 \
action trap
# Drop frames received on swp2 with a DA of 42:be:24:9b:76:20, a VID
# of 100 and a PCP of 0.
tc filter add dev swp2 ingress protocol 802.1Q flower skip_sw \
dst_mac 42:be:24:9b:76:20 vlan_id 100 vlan_prio 0 action drop
Under the hood, all rules match on DMAC, VID and PCP, but when VLAN
filtering is disabled, those are set internally by the driver to the
port-based defaults. Because we would be put in an awkward situation if
the user were to change the VLAN filtering state while there are active
rules (packets would no longer match on the specified keys), we simply
deny changing vlan_filtering unless the list of flows offloaded via
virtual links is empty. Then the user can re-add new rules.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Virtual links are a sja1105 hardware concept of executing various flow
actions based on a key extracted from the frame's DMAC, VID and PCP.
Currently the tc-flower offload code supports only parsing the DMAC if
that is the broadcast MAC address, and the VLAN PCP. Extract the key
parsing logic from the L2 policers functionality and move it into its
own function, after adding extra logic for matching on any DMAC and VID.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the register definitions for the:
- VL Lookup Table
- VL Policing Table
- VL Forwarding Table
- VL Forwarding Parameters Table
These are needed in order to perform TTEthernet operations: QoS
classification, flow-based policing and/or frame redirecting with the
switch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The VIA Rhine Ethernet interface is only present on PCI devices or
VIA/WonderMedia VT8500/WM85xx SoCs. Add platform dependencies to the
VIA_RHINE config symbol, to avoid asking the user about it when
configuring a kernel without PCI or VT8500/WM85xx support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
'Dan Carpenter' reported:
This code frees "sfi" and then dereferences it on the next line:
> kfree(sfi);
> clear_bit(sfi->index, epsfp.psfp_sfi_bitmap);
This "sfi->index" should be "index".
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function always return 0 now, we can make it return void to
simplify the code. This fixes the following coccicheck warning:
drivers/net/ethernet/microchip/encx24j600.c:609:5-8: Unneeded variable:
"ret". Return "0" on line 653
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
drivers/net/ethernet/mellanox/mlx4/en_ethtool.c:1396:5-8: Unneeded
variable: "err". Return "0" on line 1411
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function always return 0 now, we can make it return void to
simplify the code. This fixes the following coccicheck warning:
drivers/net/ethernet/dec/tulip/de4x5.c:3908:11-17: Unneeded variable:
"status". Return "0" on line 3912
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code has been marked dead for nearly 10 years. Remove it.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is dead for more than 10 years. Remove it.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/phy/mdio-bcm-iproc.c:182:5: warning:
symbol 'iproc_mdio_resume' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Zengkai <zhengzengkai@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds FLOW_ACTION_HW_STATS_DONT_CARE which tells the driver
that the frontend does not need counters, this hw stats type request
never fails. The FLOW_ACTION_HW_STATS_DISABLED type explicitly requests
the driver to disable the stats, however, if the driver cannot disable
counters, it bails out.
TCA_ACT_HW_STATS_* maintains the 1:1 mapping with FLOW_ACTION_HW_STATS_*
except by disabled which is mapped to FLOW_ACTION_HW_STATS_DISABLED
(this is 0 in tc). Add tc_act_hw_stats() to perform the mapping between
TCA_ACT_HW_STATS_* and FLOW_ACTION_HW_STATS_*.
Fixes: 319a1d1947 ("flow_offload: check for basic action hw stats type")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's very unlikely that send will become true. It's nearly always false
between 0 and 120 seconds of a session, and in most cases becomes true
only between 120 and 121 seconds before becoming false again. So,
unlikely(send) is clearly the right option here.
What happened before was that we had this complex boolean expression
with multiple likely and unlikely clauses nested. Since this is
evaluated left-to-right anyway, the whole thing got converted to
unlikely. So, we can clean this up to better represent what's going on.
The generated code is the same.
Suggested-by: Sultan Alsawaf <sultan@kerneltoast.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without setting these to NULL, clang complains in certain
configurations that have CONFIG_IPV6=n:
In file included from drivers/net/wireguard/ratelimiter.c:223:
drivers/net/wireguard/selftest/ratelimiter.c:173:34: error: variable 'skb6' is uninitialized when used here [-Werror,-Wuninitialized]
ret = timings_test(skb4, hdr4, skb6, hdr6, &test_count);
^~~~
drivers/net/wireguard/selftest/ratelimiter.c:123:29: note: initialize the variable 'skb6' to silence this warning
struct sk_buff *skb4, *skb6;
^
= NULL
drivers/net/wireguard/selftest/ratelimiter.c:173:40: error: variable 'hdr6' is uninitialized when used here [-Werror,-Wuninitialized]
ret = timings_test(skb4, hdr4, skb6, hdr6, &test_count);
^~~~
drivers/net/wireguard/selftest/ratelimiter.c:125:22: note: initialize the variable 'hdr6' to silence this warning
struct ipv6hdr *hdr6;
^
We silence this warning by setting the variables to NULL as the warning
suggests.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Users with pathological hardware reported CPU stalls on CONFIG_
PREEMPT_VOLUNTARY=y, because the ringbuffers would stay full, meaning
these workers would never terminate. That turned out not to be okay on
systems without forced preemption, which Sultan observed. This commit
adds a cond_resched() to the bottom of each loop iteration, so that
these workers don't hog the core. Note that we don't need this on the
napi poll worker, since that terminates after its budget is expended.
Suggested-by: Sultan Alsawaf <sultan@kerneltoast.com>
Reported-by: Wang Jian <larkwang@gmail.com>
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's already possible to create two different interfaces and loop
packets between them. This has always been possible with tunnels in the
kernel, and isn't specific to wireguard. Therefore, the networking stack
already needs to deal with that. At the very least, the packet winds up
exceeding the MTU and is discarded at that point. So, since this is
already something that happens, there's no need to forbid the not very
exceptional case of routing a packet back to the same interface; this
loop is no different than others, and we shouldn't special case it, but
rather rely on generic handling of loops in general. This also makes it
easier to do interesting things with wireguard such as onion routing.
At the same time, we add a selftest for this, ensuring that both onion
routing works and infinite routing loops do not crash the kernel. We
also add a test case for wireguard interfaces nesting packets and
sending traffic between each other, as well as the loop in this case
too. We make sure to send some throughput-heavy traffic for this use
case, to stress out any possible recursion issues with the locks around
workqueues.
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The K3 INTA driver, which is source TX/RX IRQs for CPSW NUSS, defines IRQs
triggering type as EDGE by default, but triggering type for CPSW NUSS TX/RX
IRQs has to be LEVEL as the EDGE triggering type may cause unnecessary IRQs
triggering and NAPI scheduling for empty queues. It was discovered with
RT-kernel.
Fix it by explicitly specifying CPSW NUSS TX/RX IRQ type as
IRQF_TRIGGER_HIGH.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addition of sja1105_port_status_ether structure into the
statistics causes the frame size to go over the warning limit:
drivers/net/dsa/sja1105/sja1105_ethtool.c:421:6: error: stack frame size of 1104 bytes in function 'sja1105_get_ethtool_stats' [-Werror,-Wframe-larger-than=]
Use dynamic allocation to avoid this.
Fixes: 336aa67bd0 ("net: dsa: sja1105: show more ethtool statistics counters for P/Q/R/S")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently bool ionic_cq.done_color is exported using
debugfs_create_u8(), which requires a cast, preventing further compiler
checks.
Fix this by switching to debugfs_create_bool(), and dropping the cast.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TJA11xx PHYs have a vendor specific Master/Slave configuration bit,
which is not compatible with IEEE 803.2-2018 spec for 100Base-T1
devices. So, provide a custom config_ange call back to solve this
problem.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of
auto-negotiation support, we needed to be able to configure the
MASTER-SLAVE role of the port manually or from an application in user
space.
The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to
force MASTER or SLAVE role. See IEEE 802.3-2018:
22.2.4.3.7 MASTER-SLAVE control register (Register 9)
22.2.4.3.8 MASTER-SLAVE status register (Register 10)
40.5.2 MASTER-SLAVE configuration resolution
45.2.1.185.1 MASTER-SLAVE config value (1.2100.14)
45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32)
The MASTER-SLAVE role affects the clock configuration:
-------------------------------------------------------------------------------
When the PHY is configured as MASTER, the PMA Transmit function shall
source TX_TCLK from a local clock source. When configured as SLAVE, the
PMA Transmit function shall source TX_TCLK from the clock recovered from
data stream provided by MASTER.
iMX6Q KSZ9031 XXX
------\ /-----------\ /------------\
| | | | |
MAC |<----RGMII----->| PHY Slave |<------>| PHY Master |
|<--- 125 MHz ---+-<------/ | | \ |
------/ \-----------/ \------------/
^
\-TX_TCLK
-------------------------------------------------------------------------------
Since some clock or link related issues are only reproducible in a
specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial
to provide generic (not 100BASE-T1 specific) interface to the user space
for configuration flexibility and trouble shooting.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent commit removed the only use of ipa_cmd_dma_task_32b_addr_add().
This function (and the IPA immediate command it implements) is no
longer needed, so get rid of it, along with all of the definitions
associated with it. Isolate its removal in a commit so it can be
easily added back again if needed.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous commit made ipa_endpoint_stop() be a trivial wrapper
around gsi_channel_stop(). Since it no longer does anything
special, just open-code it in the three places it's used.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only reason ipa_endpoint_stop() had a retry loop was that the
just-removed workaround required an IPA DMA command to occur between
attempts. The gsi_channel_stop() call that implements the stop does
its own retry loop, to cover a channel's transition from started to
stop-in-progress to stopped state.
Get rid of the unnecessary retry loop in ipa_endpoint_stop().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipa_endpoint_stop(), a workaround is used for IPA version 3.5.1
where a 1-byte DMA request is issued between GSI channel stop
retries.
It turns out that this workaround is only required for IPA versions
3.1 and 3.2, and we don't support those. So remove the call to
ipa_endpoint_stop_rx_dma() in that function. That leaves that
function unused, so get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipa_endpoint_stop(), for TX endpoints we set the number of retries
to 0. When we break out of the loop, retries being 0 means we return
EIO rather than the value of ret (which should be 0).
Fix this by using a non-zero retry count for both RX and TX
channels, and just break out of the loop after calling
gsi_channel_stop() for TX channels. This way only RX channels
will retry, and the retry count will be non-zero at the end
for TX channels (so the proper value gets returned).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 713b6ebb4c)
Signed-off-by: David S. Miller <davem@davemloft.net>
A "delay mode" feature was put in place to work around a problem
that was observed during development of the upstream IPA driver. It
used TX endpoint "delay mode" in order to prevent transmitting
packets toward the modem before it was ready.
A race condition that would explain the problem has long since been
fixed, and we have concluded that the "delay mode" feature is no
longer required. So get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new helper function that encapsulates enabling or disabling
suspend on an RX endpoint. It returns the previous state of the
endpoint (true means suspend mode was enabled).
Create another function that handles enabling or disabling delay mode
on a TX endpoint. Delay mode does not work correctly on IPA version
4.2, so we don't currently use it (and shouldn't).
We only set delay mode in one case, and although we don't expect an
endpoint to already be in delay mode, it doesn't really matter if it
was. So the delay function doesn't return a value.
Stop issuing warnings if the previous suspend or delay mode state
differs from what is expected.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ipa_endpoint_init_ctrl() so it returns the previous state
(whether suspend or delay mode was enabled) rather than indicating
whether the request caused a change in state. This makes it easier
to understand what's happening where called.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In gsi_channel_reset(), RX channels are subjected to two consecutive
CHANNEL_RESET commands. This workaround should only be used for IPA
version 3.5.1, and for newer hardware "can lead to unwanted behavior."
Only issue the second CHANNEL_RESET command for legacy hardware.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In several places, a Boolean flag is used in the GSI code to
indicate whether the "doorbell engine" should be enabled or not
when a channel is configured. This is basically done to abstract
this property from the IPA version; the GSI code doesn't otherwise
"know" what the IPA hardware version is. The doorbell engine is
enabled only for IPA v3.5.1, not for IPA v4.0 and later.
The next patch makes another change that affects behavior during
channel reset (which also involves programming the channel). It
also distinguishes IPA v3.5.1 hardware from newer hardware.
Rather than creating another flag whose value matches the "db_enable"
value, just rename "db_enable" to be "legacy" so it can be used to
signal more than just the special doorbell handling.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
One may notice that automatically-learnt entries 'never' expire, even
though the bridge configures the address age period at 300 seconds.
Actually the value written to hardware corresponds to a time interval
1000 times higher than intended, i.e. 83 hours.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Faineli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running 'bridge fdb dump' on Felix, sometimes learnt and static MAC
addresses would appear, sometimes they wouldn't.
Turns out, the MAC table has 4096 entries on VSC7514 (Ocelot) and 8192
entries on VSC9959 (Felix), so the existing code from the Ocelot common
library only dumped half of Felix's MAC table. They are both organized
as a 4-way set-associative TCAM, so we just need a single variable
indicating the correct number of rows.
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new flexible sleep function fsleep() to merge the udelay and msleep
polling functions. We can safely do this because no polling function
is used in atomic context in this driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the sja1105 external timestamping input is not as generic
as we thought. When fed a signal with 50% duty cycle, it will timestamp
both the rising and the falling edge. When fed a short pulse signal,
only the timestamp of the falling edge will be seen in the PTPSYNCTS
register, because that of the rising edge had been overwritten. So the
moral is: don't feed it short pulse inputs.
Luckily this is not a complete deal breaker, as we can still work with
1 Hz square waves. But the problem is that the extts polling period was
not dimensioned enough for this input signal. If we leave the period at
half a second, we risk losing timestamps due to jitter in the measuring
process. So we need to increase it to 4 times per second.
Also, the very least we can do to inform the user is to deny any other
flags combination than with PTP_RISING_EDGE and PTP_FALLING_EDGE both
set.
Fixes: 747e5eb31d ("net: dsa: sja1105: configure the PTP_CLK pin as EXT_TS or PER_OUT")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new phy_package_shared common storage to ease the package
initialization and to access the global registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are packages which contain multiple PHY devices, eg. a quad PHY
transceiver. Provide functions to allocate and free shared storage.
Usually, a quad PHY contains global registers, which don't belong to any
PHY. Provide convenience functions to access these registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_update_features() must be called with the rtnl lock taken. Not
doing so triggers a warning, as ASSERT_RTNL() is used in
__netdev_update_features(), the first function called by
netdev_update_features(). Fix this.
Fixes: c850240b6c ("net: macsec: report real_dev features when HW offloading is enabled")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
