The F81532/534 had auto RTS direction support for RS485 mode.
We'll read it from internal Flash with address 0x2f01~0x2f04 for 4 ports.
There are 4 conditions below:
0: F81534_PORT_CONF_RS232.
1: F81534_PORT_CONF_RS485.
2: value error, default to F81534_PORT_CONF_RS232.
3: F81534_PORT_CONF_RS485_INVERT.
F81532/534 Clock register (offset +08h)
Bit0: UART Enable (always on)
Bit2-1: Clock source selector
00: 1.846MHz.
01: 18.46MHz.
10: 24MHz.
11: 14.77MHz.
Bit4: Auto direction(RTS) control (RTS pin Low when TX)
Bit5: Invert direction(RTS) when Bit4 enabled (RTS pin high when TX)
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[ johan: rename mode-mask define, and only use GENMASK() for masks ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81532/534 had 4 clocksource 1.846/18.46/14.77/24MHz and baud rates
can be up to 1.5Mbits with 24MHz.
This device may generate data overrun when baud rate setting to 921600bps
or higher with old UART trigger level setting (8x14=112) with full
loading. We'll change trigger level from 8x14=112 to 8x8=64 to avoid data
overrun.
Also the read/write of EP0 will be affected by this patch. The worst case
of responding time is 20s when all serial port are full loading and trying
to access EP0, so we change EP0 timeout from 10 to 20s.
F81532/534 Clock register (offset +08h)
Bit0: UART Enable (always on)
Bit2-1: Clock source selector
00: 1.846MHz.
01: 18.46MHz.
10: 24MHz.
11: 14.77MHz.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[ johan: only use GENMASK() for masks ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The UAS mode of Norelsys NS1068(X) is reported to fail to work on
several platforms with the following error message:
xhci-hcd xhci-hcd.0.auto: ERROR Transfer event for unknown stream ring slot 1 ep 8
xhci-hcd xhci-hcd.0.auto: @00000000bf04a400 00000000 00000000 1b000000 01098001
And when trying to mount a partition on the disk the disk will
disconnect from the USB controller, then after re-connecting the device
will be offlined and not working at all.
Falling back to USB mass storage can solve this problem, so ignore UAS
function of this chip.
Cc: stable@vger.kernel.org
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old way of usb wakeup only supports platform with single xHCI IP,
such as mt8173, but mt2712 has two xHCI IPs, so rebuild its flow and
supports the new glue layer of usb wakeup on mt2712 which is different
from mt8173.
Due to there is a hardware bug with the LINE STATE wakeup mode on
mt8173 which causes wakeup failure by low speed devices, and also
because IP SLEEP mode can cover all functions of LINE STATE mode,
it is unused in fact, and will not support it later, so remove it at
the same time.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old way of usb wakeup only supports platform with single SSUSB IP,
such as mt8173, but mt2712 has two SSUSB IPs, so rebuild its flow and
also supports the new glue layer of usb wakeup on mt2712 which is
different from mt8173.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When failing to get extcon device, extcon_get_edev_by_phandle()
may return different error codes, but not only -EPROBE_DEFER,
so can't always return -EPROBE_DEFER, and fix it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ohci-da8xx device only has one clock, so a con_id is not needed, so
remove it. This way we don't have to add an unnecessary property to the
device tree bindings for the clock.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is only one clock for the DA8xx MUSB device, so we don't need the
con_id, so remove it. This way we don't have to add an unnecessary
property to the device tree bindings for the clock.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error-handling pathways in usb_add_gadget_udc_release() are messed
up. Aside from the uninformative statement labels, they can deallocate
the udc structure after calling put_device(), which is a double-free.
This was observed by KASAN in automatic testing.
This patch cleans up the routine. It preserves the requirement that
when any failure occurs, we call put_device(&gadget->dev).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
CC: <stable@vger.kernel.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Automated tests triggered this by opening usbmon and accessing the
mmap while simultaneously resizing the buffers. This bug was with
us since 2006, because typically applications only size the buffers
once and thus avoid racing. Reported by Kirill A. Shutemov.
Reported-by: <syzbot+f9831b881b3e849829fc@syzkaller.appspotmail.com>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch moves TIOCGSERIAL ioctl case to get_serial_info function.
Signed-off-by: Mikhail Zaytsev <flashed@mail.ru>
[johan: keep the automatic __user pointer variable in ioctl callback ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The patch removes unused TIOCSSERIAL ioctl case and adds the default block
to the switch. This will make the ioctl return -ENOTTY to user space (e.g.
setserial), which indicates that TIOCSSERIAL really isn't supported for
these devices currently.
Note that these (dummy) ioctl implementations where added by commit
2f430b4bba ("USB: ark3116: Add TIOCGSERIAL and TIOCSSERIAL ioctl
calls.") back in 2006. This in turn appears to have been triggered by a
change in a user space tool, wvdial, which started erroring out if
either was missing.
There are some bug reports about that against wvdial from around that
time, and looking at the wvstreams (library) code now, it looks like the
issue has indeed been resolved by handling errors more gracefully (e.g.
just logging them).
User space really should not make assumptions about these ioctl always
being implemented, but if this turns out to be a problem for anyone
using this driver, we'll add TIOCSSERIAL back in some form.
Signed-off-by: Mikhail Zaytsev <flashed@mail.ru>
[johan: amend commit message with backstory ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Kishon writes:
phy: for 4.16
*) Fix in exynos5-usbdrd to enumerate SuperSpeed devices on Odroid XU3
*) Fix in Broadcom USB PHY to get Dell Low Speed keyboards working
*) Fix in Broadcom USB PHY to power down the PHY when XHCI disabled
to save power
*) Fix in Broadcom USB PHY to prevent abort in DRD mode
*) Fix in Broadcom USB PHY to use the correct dt properties
*) Fix in Mediatek PHY to detect device connection
*) Make getting resource optional for Mediatek V1 TPHY
*) Cleanup in Mediatek PHY
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Felipe writes:
usb: changes for v4.16 merge window
Not many changes here, the most important being an improvement for TI's
AM57xx and DRA7xx devices which allows them to disable a metastability
workaround in situations where we know what's going on.
Other than that, we have a set of changes on Renesas UDC to make the
code a little easier to read and maintain while also better supporting
extcon framework.
The u_serial adaptation layer learned to use kfifo instead of cooking
its own FIFO implementation.
DWC3 learned to decode a few more USB requests on the trace output.
v_send_ret_submit() handles urb with a null transfer_buffer, when it
replays a packet with potential malicious data that could contain a
null buffer.
Add a check for the condition when actual_length > 0 and transfer_buffer
is null.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usbip_dump_usb_device() and usbip_dump_urb() print kernel addresses.
Remove kernel addresses from usb device and urb debug msgs and improve
the message content.
Instead of printing parent device and bus addresses, print parent device
and bus names.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Harden CMD_SUBMIT path to handle malicious input that could trigger
large memory allocations. Add checks to validate transfer_buffer_length
and number_of_packets to protect against bad input requesting for
unbounded memory allocations.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling msg_data_left(&msg) is only useful for its return value,
which in this particular case is ignored.
Fix this by removing such call.
Addresses-Coverity-ID: 1427080
Fixes: 90120d15f4 ("usbip: prevent leaking socket pointer address in messages")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the ELV ALC 8xxx Battery Charging device
to the list of USB IDs of drivers/usb/serial/cp210x.c
Signed-off-by: Christian Holl <cyborgx1@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch fix the following build warning:
drivers/usb/musb/musb_host.c:1809:8: warning: variable 'pipe' set but not used [-Wunused-but-set-variable]
by removing the pipe variable in musb_host_rx()
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix the following warning
drivers/usb/musb/musb_host.c:223:8: warning: variable 'frame' set but not used [-Wunused-but-set-variable]
by remove the frame variable in musb_start_urb().
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding phy calibration sequence for USB 3.0 DRD PHY present on
Exynos5420/5800 systems.
This calibration facilitates setting certain PHY parameters viz.
the Loss-of-Signal (LOS) Detector Threshold Level, as well as
Tx-Vboost-Level for Super-Speed operations.
Additionally we also set proper time to wait for RxDetect measurement,
for desired PHY reference clock, so as to solve issue with enumeration
of few USB 3.0 devices, like Samsung SUM-TSB16S 3.0 USB drive
on the controller.
We are using CR_port for this purpose to send required data
to override the LOS values.
On testing with USB 3.0 devices on USB 3.0 port present on
SMDK5420, and peach-pit boards should see following message:
usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
and without this patch, should see below shown message:
usb 1-1: new high-speed USB device number 2 using xhci-hcd
[Also removed unnecessary extra lines in the register macro definitions]
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
[adapted to use phy_calibrate as entry point]
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When plugging in a USB webcam I see the following message:
xhci_hcd 0000:04:00.0: WARN Successful completion on short TX: needs
XHCI_TRUST_TX_LENGTH quirk?
handle_tx_event: 913 callbacks suppressed
All is quiet again with this patch (and I've done a fair but of soak
testing with the camera since).
Cc: <stable@vger.kernel.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trying to read from debugfs after the system has resumed from
hibernate causes a use-after-free and thus a protection fault.
Steps to reproduce:
Hibernate system, resume from hibernate, then run
$ cat /sys/kernel/debug/usb/xhci/*/command-ring/enqueue
[ 3902.765086] general protection fault: 0000 [#1] PREEMPT SMP
...
[ 3902.765136] RIP: 0010:xhci_trb_virt_to_dma.part.50+0x5/0x30
...
[ 3902.765178] Call Trace:
[ 3902.765188] xhci_ring_enqueue_show+0x1e/0x40
[ 3902.765197] seq_read+0xdb/0x3a0
[ 3902.765204] ? __handle_mm_fault+0x5fb/0x1210
[ 3902.765211] full_proxy_read+0x4a/0x70
[ 3902.765219] __vfs_read+0x23/0x120
[ 3902.765228] vfs_read+0x8e/0x130
[ 3902.765235] SyS_read+0x42/0x90
[ 3902.765242] do_syscall_64+0x6b/0x290
[ 3902.765251] entry_SYSCALL64_slow_path+0x25/0x25
The issue is caused by the xhci ring structures being reallocated
when the system is resumed, but pointers to the old structures
being retained in the debugfs files "private" field:
The proposed patch fixes this issue by storing a pointer to the xhci_ring
field in the xhci device structure in debugfs rather than directly
storing a pointer to the xhci_ring.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Signed-off-by: Alexander Kappner <agk@godking.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Free the virt_device and its debugfs_private member together.
When resuming from hibernate the .free_dev callback unconditionally
freed the debugfs_private member, but could leave virt_device intact.
This triggered a NULL pointer dereference after resume when usbmuxd
sent a USBDEVFS_SETCONFIGURATION ioctl to a device, trying to add a
endpoint debugfs entry to a already freed debugfs_private pointer.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Reported-by: Alexander Kappner <agk@godking.net>
Tested-by: Alexander Kappner <agk@godking.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan writes
USB-serial fixes for v4.15-rc6
Here are some new device ids for ftdi_sio, option and qcserial.
Note that the qcserial patch enables the SetControlLineState request
(used to raise DTR/RTS) for the GPS interface of all devices using the
Sierra Wireless layout. This was required for the Sierra Wireless EM7565
and has been tested using several other modems as well.
All but the final commit have been in linux-next without any reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Commit e0429362ab
("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e")
introduced quirk to workaround an issue with some Logitech webcams.
There is one more model that has the same issue - C925e, so applying
the same quirk as well.
See aforementioned commit message for detailed explanation of the problem.
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usbip driver is leaking socket pointer address in messages. Remove
the messages that aren't useful and print sockfd in the ones that
are useful for debugging.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 3.1 devices are not detected as 3.1 capable since 4.15-rc3 due to a
off by one in commit 81cf4a4536 ("USB: core: Add type-specific length
check of BOS descriptors")
It uses USB_DT_USB_SSP_CAP_SIZE() to get SSP capability size which takes
the zero based SSAC as argument, not the actual count of sublink speed
attributes.
USB3 spec 9.6.2.5 says "The number of Sublink Speed Attributes = SSAC + 1."
The type-specific length check patch was added to stable and needs to be
fixed there as well
Fixes: 81cf4a4536 ("USB: core: Add type-specific length check of BOS descriptors")
Cc: linux-stable <stable@vger.kernel.org>
CC: Masakazu Mokuno <masakazu.mokuno@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear Feature Endpoint Halt should reset the data toggle even if the
endpoint isn't halted. Host should manage to clear the host side data
toggle to keep in sync with the device.
Test by sending a "3 data packet URB" before and after clearing the halt.
this should create a toggle sequence with two consecutive DATA0 packets.
A successful test sequence looks like this
ClearFeature(ENDPOINT_HALT) - initial toggle clear
DATA0 (max packet sized)
DATA1 (max packet sized)
DATA0 (zero length packet)
ClearFeature(ENDPOINT_HALT) - resets toggle
DATA0 (max packet sized), if clear halt fails then toggle is DATA1
DATA1 (max packet sized)
DATA0 (zero length packet)
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB SS and SSP hubs provide wHubDelay values on their hub descriptor
which we should inform the USB Device about.
The USB Specification 3.0 explains, on section 9.4.11, how to
calculate the value and how to issue the request. Note that a
USB_REQ_SET_ISOCH_DELAY is valid on all device states (Default,
Address, Configured), we just *chose* to issue it from Address state
right after successfully fetching the USB Device Descriptor.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
