During a device failover or partition migration reset, it is not
necessary to disable the backing adapter since it should not be
running yet and its Command-Response Queue is closed. Sending
device commands during this time could result in an error or
timeout disrupting the reset process. In these cases, just halt
transmissions, clean up resources, and continue with reset.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a function to halt network operations and clean up any
unused or outstanding socket buffers. Then, during device close,
disable backing adapter before halting all queues and performing
cleanup. This ensures all backing device operations will be
stopped before the driver cleans up shared resources.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some dead code now that RX pools are being cleaned. This
was included to wait until any pending RX queue interrupts are
processed, but NAPI polling should be disabled by this point.
Another minor change is to use the net device parameter for any
print functions instead of accessing it from the adapter structure.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for VF driver inner interface
hclgevf_ops.get_tqps_and_rss_info. This interface will be
used in the initialization process.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 driver should alloc netdev with max support ring num, as
driver support change netdev count by ethtool -L.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Command HCLGE_OPC_CFG_COM_TQP_QUEUE should use queue id in the
function, but command HCLGE_OPC_RESET_TQP_QUEUE should use global
queue id.
This patch fixes the queue id about queue enable/disable/reset.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the endian issue when PF get mbx message flag.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver check the out_vld bit when get a new cmdq BD, if the bit is 1,
the BD is valid. driver Should set the bit 0 after used and hw will
set the bit 1 if get a valid BD.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF driver should get the real rss_size which is assigned
by host PF, not rss_size_max.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ESN is not supported with IPSec device offload.
This patch adds ESN support to IPsec device offload.
Implementing new xfrm device operation to synchronize offloading device
ESN with xfrm received SN. New QP command to update SA state at the
following:
ESN 1 ESN 2 ESN 3
|-----------*-----------|-----------*-----------|-----------*
^ ^ ^ ^ ^ ^
^ - marks where QP command invoked to update the SA ESN state
machine.
| - marks the start of the ESN scope (0-2^32-1). At this point move SA
ESN overlap bit to zero and increment ESN.
* - marks the middle of the ESN scope (2^31). At this point move SA
ESN overlap bit to one.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Yossef Efraim <yossefe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
New function for getting driver internal sa entry from xfrm state.
All checks are done in one function.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to add a context to the FPGA, we need to get both the software
transform context (which includes the keys, etc) and the
source/destination IPs (which are included in the steering
rule). Therefore, we register new set of firmware like commands for
the FPGA. Each time a rule is added, the steering core infrastructure
calls the FPGA command layer. If the rule is intended for the FPGA,
it combines the IPs information with the software transformation
context and creates the respective hardware transform.
Afterwards, it calls the standard steering command layer.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current code has one layer that executed FPGA commands and
the Ethernet part directly used this code. Since downstream patches
introduces support for IPSec in mlx5_ib, we need to provide some
abstractions. This patch refactors the accel code into one layer
that creates a software IPSec transformation and another one which
creates the actual hardware context.
The internal command implementation is now hidden in the FPGA
core layer. The code also adds the ability to share FPGA hardware
contexts. If two contexts are the same, only a reference count
is taken.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch adds V2 command support.
New fpga devices support extended features (udp encap, esn etc...), this
features require new hardware sadb format therefore we have a new version
of commands to manipulate it.
Signed-off-by: Yossef Efraim <yossefe@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current hardware decrypts and authenticates incoming ESP packets.
Subsequently, the software extracts the nexthdr field, truncates the
trailer and adjusts csum accordingly.
With this patch and a capable device, the trailer is being removed
by the hardware and the nexthdr field is conveyed via PET. This way
we avoid both the need to access the trailer (cache miss) and to
compute its relative checksum, which significantly improve
the performance.
Experiment shows that trailer removal improves the performance by
2Gbps, (netperf). Both forwarding and host-to-host configurations.
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current code assume only SA QP commands.
Refactor in order to pave the way for new QP commands:
1. Generic cmd response format.
2. SA cmd checks are in dedicated functions.
3. Aligned debug prints.
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix build break of mlx5_accel_ipsec_device_caps is not defined when
MLX5_ACCEL is not selected, use MLX5_IPSEC_DEV instead which handles
such case.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Doug Ledford <dledford@redhat.com>
Marvell PPv2 controller can be used to implement packet filtering based
on the destination MAC address. This is already used to implement
multicast filtering. This patch adds support for Unicast filtering.
Filtering is based on so-called "TCAM entries" to implement filtering.
Due to their limited number and the fact that these are also used for
other purposes, we reserve 80 entries for both unicast and multicast
filters. On top of the broadcast address, and each interface's own MAC
address, we reserve 25 entries per port, 4 for unicast filters, 21 for
multicast.
Whenever unicast or multicast range for one port is full, the filtering
is disabled and port goes into promiscuous mode for the given type of
addresses.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_prs_mac_da_accept function takes into parameter both the
struct representing the controller and the port id. This is meaningful
when we want to create TCAM entries for non-initialized ports, but in
this case we expect the port to be initialized before starting adding or
removing MAC addresses to the per-port filter.
This commit changes the function so that it takes struct mvpp2_port as
a parameter instead.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not set 'needs_free_netdev' as we do call free_netdev
for mgmt net devices, doing both hits BUG_ON.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
instantiation of VF's on different adapters fails, copy
adapter index and chip type to PF0-3 adapter instances
to fix the issue.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-updates-2018-02-28-1 (IPSec-1)
This series consists of some fixes and refactors for the mlx5 drivers,
especially around the FPGA and flow steering. Most of them are trivial
fixes and are the foundation of allowing IPSec acceleration from user-space.
We use flow steering abstraction in order to accelerate IPSec packets.
When a user creates a steering rule, [s]he states that we'll carry an
encrypt/decrypt flow action (using a specific configuration) for every
packet which conforms to a certain match. Since currently offloading these
packets is done via FPGA, we'll add another set of flow steering ops.
These ops will execute the required FPGA commands and then call the
standard steering ops.
In order to achieve this, we need that the commands will get all the
required information. Therefore, we pass the fte object and embed the
flow_action struct inside the fte. In addition, we add the shim layer
that will later be used for alternating between the standard and the
FPGA steering commands.
Some fixes, like " net/mlx5e: Wait for FPGA command responses with a timeout"
are very relevant for user-space applications, as these applications could
be killed, but we still want to wait for the FPGA and update the kernel's
database.
Regards,
Aviad and Matan
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
RX rings can fit most of the time in a contiguous piece of memory,
so lets use kvzalloc_node/kvfree instead of vzalloc_node/vfree
Note that kvzalloc_node() automatically falls back to another node,
there is no need to do the fallback ourselves.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/cisco/enic/vnic_dev.c:1294:9-10: WARNING: return of 0/1 in function 'vnic_dev_capable_udp_rss' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Fixes: 48398b6e70 ("enic: set UDP rss flag")
CC: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smsc911x driver will crash if it is rmmod'ed while the netdev
is up like:
Call trace:
phy_detach+0x94/0x150
phy_disconnect+0x40/0x50
smsc911x_stop+0x104/0x128 [smsc911x]
__dev_close_many+0xb4/0x138
dev_close_many+0xbc/0x190
rollback_registered_many+0x140/0x460
rollback_registered+0x68/0xb0
unregister_netdevice_queue+0x100/0x118
unregister_netdev+0x28/0x38
smsc911x_drv_remove+0x58/0x130 [smsc911x]
platform_drv_remove+0x30/0x50
device_release_driver_internal+0x15c/0x1f8
driver_detach+0x54/0x98
bus_remove_driver+0x64/0xe8
driver_unregister+0x34/0x60
platform_driver_unregister+0x20/0x30
smsc911x_cleanup_module+0x14/0xbca8 [smsc911x]
SyS_delete_module+0x1e8/0x238
__sys_trace_return+0x0/0x4
This is caused by the mdiobus being unregistered/free'd
and the code in phy_detach() attempting to manipulate mdio
related structures from unregister_netdev() calling close()
To fix this, we delay the mdiobus teardown until after
the netdev is deregistered.
Reported-by: Matt Sealey <matt.sealey@arm.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the warning messages/call traces seen if DMA debug is
enabled, In case of fragmented skb's memory was allocated using
dma_map_page but freed using dma_unmap_single. This patch modifies buffer
allocations in TX path to use dma_map_page in all the places and
dma_unmap_page while freeing the buffers.
Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rdma requires ILT Memory to be allocated for it's QPs.
Each ILT entry points to a page used by several Rdma QPs.
To avoid allocating all the memory in advance, the rdma
implementation dynamically allocates memory as more QPs are
added, however it does not dynamically free the memory.
The memory should have been freed on rmmod qedr, but isn't.
This patch adds the memory freeing on rmmod qedr (currently
it will be freed with qed is removed).
An outcome of this bug, is that if qedr is unloaded and loaded
without unloaded qed, there will be no more RoCE traffic.
The reason these are related, is that the logic of detecting the
first QP ever opened is by asking whether ILT memory for RoCE has
been allocated.
In addition, this patch modifies freeing of the Task context to
always use the PROTOCOLID_ROCE and not the protocol passed,
this is because task context for iWARP and ROCE both use the
ROCE protocol id, as opposed to the connection context.
Fixes: dbb799c397 ("qed: Initialize hardware for new protocols")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2018-03-05
This series contains updates to igb only.
Corinna Vinschen adds the support for trusted VFs into the igb driver.
Mika fixes an issue where PCIe device is physically unplugged can cause
a kernel crash. This issue is that netif_device_detach() is called in
these cases, which prevents netif_unregister() from bringing the device
down properly.
Christophe JAILLET fixes an issue with igb where HWTSTAMP_TX_ON was
being handled like a bit mask and not a value.
v2: dropped the e1000e fix from the series since I will be pushing it
through David Miller's net tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-03-05
This series contains fixes to e1000e only.
Benjamin Poirier provides all but one fix in this series, starting with
workaround for a VMWare e1000e emulation issue where ICR reads 0x0 on
the emulated device. Partially reverted a previous commit dealing with
the "Other" interrupt throttling to avoid unforeseen fallout from these
changes that are not strictly necessary. Restored the ICS write for
receive and transmit queue interrupts in the case that txq or rxq bits
were set in ICR and the Other interrupt handler read and cleared ICR
before the queue interrupt was raised. Fixed an bug where interrupts
may be missed if ICR is read while INT_ASSERTED is not set, so avoid the
problem by setting all bits related to events that can trigger the Other
interrupt in IMS. Fixed the return value for check_for_link() when
auto-negotiation is off.
Pierre-Yves Kerbrat fixes e1000e to use dma_zalloc_coherent() to make
sure the ring is memset to 0 to prevent the area from containing
garbage.
v2: added an additional e1000e fix to the series
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, deleting a flow steering entry only got the index.
Since the FPGA implementation of FTE's deletion might need to dig
inside the FTE itself, we would like to get the FTE's context.
Changing the interface to pass the FTE context.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
fte objects contain the match value and action. Currently, extending
the actions require in adding them both to the API and fs_fte.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, we don't support egress flow steering namespace in mlx5
flow steering core implementation. However, when we want to encrypt
a packet, we model it as a flow steering rule in the egress path.
To overcome this, we add an empty egress namespace to flow steering.
This namespace is initialized only when ipsec support exists.
In the future, this will grow to a full blown full steering
implementation, resembling the ingress path.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The shim layer allows each namespace to define possibly different
functionality for add/delete/update commands. The shim layer
introduced here, will be used to support flow steering with the FPGA.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The has_tag member will indicate whether a tag action was specified
in flow specification.
A flow tag 0 = MLX5_FS_DEFAULT_FLOW_TAG is assumed a valid flow tag
that is currently used by mlx5 RDMA driver, whereas in HW flow_tag = 0
means that the user doesn't care about flow_tag. HW always provide
a flow_tag = 0 if all flow tags requested on a specific flow are 0.
So we need a way (in the driver) to differentiate between a user really
requesting flow_tag = 0 and a user who does not care, in order to be
able to report conflicting flow tags on a specific flow.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Some flow steering namespace initialization (i.e. egress namespace)
might depend on FPGA capabilities. Changing the initialization order
such that the FPGA will be initialized before flow steering.
Flow steering fs cmds initialization might depend on
IPSec capabilities. Changing the initialization order such
that the IPSec will be initialized before flow steering as well.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This is already done by xfrm layer between state_dev_del callback
to state_dev_free callback.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Generally, FPGA IPSec commands must always complete.
We want to wait for one minute for them to complete gracefully also
when killing a process.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Correct spelling of National Semi-conductor (no hyphen)
in drivers/net/ethernet/.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
Descriptor rings were not initialized at zero when allocated
When area contained garbage data, it caused skb_over_panic in
e1000_clean_rx_irq (if data had E1000_RXD_STAT_DD bit set)
This patch makes use of dma_zalloc_coherent to make sure the
ring is memset at 0 to prevent the area from containing garbage.
Following is the signature of the panic:
IODDR0@0.0: skbuff: skb_over_panic: text:80407b20 len:64010 put:64010 head:ab46d800 data:ab46d842 tail:0xab47d24c end:0xab46df40 dev:eth0
IODDR0@0.0: BUG: failure at net/core/skbuff.c:105/skb_panic()!
IODDR0@0.0: Kernel panic - not syncing: BUG!
IODDR0@0.0:
IODDR0@0.0: Process swapper/0 (pid: 0, threadinfo=81728000, task=8173cc00 ,cpu: 0)
IODDR0@0.0: SP = <815a1c0c>
IODDR0@0.0: Stack: 00000001
IODDR0@0.0: b2d89800 815e33ac
IODDR0@0.0: ea73c040 00000001
IODDR0@0.0: 60040003 0000fa0a
IODDR0@0.0: 00000002
IODDR0@0.0:
IODDR0@0.0: 804540c0 815a1c70
IODDR0@0.0: b2744000 602ac070
IODDR0@0.0: 815a1c44 b2d89800
IODDR0@0.0: 8173cc00 815a1c08
IODDR0@0.0:
IODDR0@0.0: 00000006
IODDR0@0.0: 815a1b50 00000000
IODDR0@0.0: 80079434 00000001
IODDR0@0.0: ab46df40 b2744000
IODDR0@0.0: b2d89800
IODDR0@0.0:
IODDR0@0.0: 0000fa0a 8045745c
IODDR0@0.0: 815a1c88 0000fa0a
IODDR0@0.0: 80407b20 b2789f80
IODDR0@0.0: 00000005 80407b20
IODDR0@0.0:
IODDR0@0.0:
IODDR0@0.0: Call Trace:
IODDR0@0.0: [<804540bc>] skb_panic+0xa4/0xa8
IODDR0@0.0: [<80079430>] console_unlock+0x2f8/0x6d0
IODDR0@0.0: [<80457458>] skb_put+0xa0/0xc0
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<804079c8>] e1000_clean_rx_irq+0x188/0x3e8
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<80468b48>] __dev_kfree_skb_any+0x88/0xa8
IODDR0@0.0: [<804101ac>] e1000e_poll+0x94/0x288
IODDR0@0.0: [<8046e9d4>] net_rx_action+0x19c/0x4e8
IODDR0@0.0: ...
IODDR0@0.0: Maximum depth to print reached. Use kstack=<maximum_depth_to_print> To specify a custom value (where 0 means to display the full backtrace)
IODDR0@0.0: ---[ end Kernel panic - not syncing: BUG!
Signed-off-by: Pierre-Yves Kerbrat <pkerbrat@kalray.eu>
Signed-off-by: Marius Gligor <mgligor@kalray.eu>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
