We need to call drm_helper_hpd_irq_event() on resume to properly detect
monitor connection / disconnection on some laptops. For runtime-resume
(which gets called on resume from normal suspend too) we must call
drm_helper_hpd_irq_event() from a workqueue to avoid a deadlock.
Rename acpi_work to hpd_work, and move it out of the #ifdef CONFIG_ACPI
blocks to make it suitable for generic work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The new atomic modesetting/pageflip code for nv50+ for
Linux 4.10+ no longer uses pageflip irq's to signal
flip completion. Instead it polls for flip completion
from within a kthread/work queue.
This creates a race between the vblank irq handler
updating the vblank count and timestamp for the
vblank of flip completion, and the kthread's
polling code detecting flip completion and sending
out the flip completion event.
Depending on who executes a few microseconds earlier,
the flip completion event will either contain correct
count/timestamp or a stale count/timestamp from the
previous vblank. This error was observed for about
50% of all executed flips, e.g., observable under DRI2
by the Xorg.log filling with flip handler warning
messages.
Call drm_accurate_vblank_count() before sending
out flip completion events to enforce a vblank
count/ts update for the vblank of flip completion
and avoid stale counts/timestamps.
This fix leads to one redundant call to drm_update_vblank_count
for each completed flip, but no other side effects. On
a ~6 year old Core i7 M620@ 2.67GHz the redundant call
costs about 10 usecs per flip
Successfully tested on GeForce 9500/9600/330M so far.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Previous value really only made sense on armv7 without LPAE. Everything
that supports more than 4g of memory also has iommu's that can map
anything.
Signed-off-by: Rob Clark <robdclark@gmail.com>
In add_components_mdp, we parse the endpoints in MDP output ports
using the helper for_each_endpoint_of_node(). Our function calls
of_node_put() on the endpoint node before we iterate over the
next one. This is already done by the helper, and results in
trying to decrement the refcount twice.
Remove the extra of_node_put calls. This fixes warnings seen when
we try to insert the driver as a module on IFC6410.
Reported-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The mode_config->max_{width,height} is for the maximum size of a fb, not
the max scanout limits (of the layer-mixer). It is legal, and in fact
common, to create a larger fb, only only scan-out a smaller part of it.
For example multi-monitor configurations for x11, or android wallpaper
layer (which is created larger than the screen resolution for fast
scrolling by just changing the src x/y coordinates).
Signed-off-by: Rob Clark <robdclark@gmail.com>
Previously, SMP block allocation was not checked in the plane's
atomic_check() fxn, so we could fail allocation SMP block allocation at
atomic_update() time. Re-work the block allocation to request blocks
during atomic_check(), but not update the hw until committing the atomic
update.
Since SMP blocks allocated at atomic_check() time, we need to manage the
SMP state as part of mdp5_state (global atomic state). This actually
ends up significantly simplifying the SMP management, as the SMP module
does not need to manage the intermediate state between assigning new
blocks before setting flush bits and releasing old blocks after vblank.
(The SMP registers and SMP allocation is not double-buffered, so newly
allocated blocks need to be updated in kms->prepare_commit() released
blocks in kms->complete_commit().)
Signed-off-by: Rob Clark <robdclark@gmail.com>
(re)assign the hw pipes to planes based on required caps, and to handle
situations where we could not modify an in-use plane (ie. SMP block
reallocation).
This means all planes advertise the superset of formats and properties.
Userspace must (as always) use atomic TEST_ONLY step for atomic updates,
as not all planes may be available for use on every frame.
The mapping of hwpipe to plane is stored in mdp5_state, so that state
updates are atomically committed in the same way that plane/etc state
updates are managed. This is needed because the mdp5_plane_state keeps
a pointer to the hwpipe, and we don't want global state to become out
of sync with the plane state if an atomic update fails, we hit deadlock/
backoff scenario, etc. The use of state_lock keeps multiple parallel
updates which both re-assign hwpipes properly serialized.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add basic state duplication/apply mechanism. Following commits will
move actual global hw state into this.
The state_lock allows multiple concurrent updates to proceed as long as
they don't both try to alter global state. The ww_mutex mechanism will
trigger backoff in case of deadlock between multiple threads trying to
update state.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Split out the hardware pipe specifics from mdp5_plane. To start, the hw
pipes are statically assigned to planes, but next step is to assign the
hw pipes during plane->atomic_check() based on requested caps (scaling,
YUV, etc). And then hw pipe re-assignment if required if required SMP
blocks changes.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Just use plane->name now that it is a thing. In a following patch, once
we dynamically assign hw pipes to planes, it won't make sense to name
planes the way we do, so this also partly reduces churn in following
patch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
We can do this all from mdp5_plane_complete_commit(), so simplify things
a bit and drop mdp5_plane_complete_flip().
Signed-off-by: Rob Clark <robdclark@gmail.com>
Plane's (pipes) can be assigned dynamically with atomic, so it doesn't
make much sense to name the pipe after it's primary plane.
Signed-off-by: Rob Clark <robdclark@gmail.com>
These are really plane-id's, not crtc-id's. Only connection to CRTCs is
that they are used as primary-planes.
Current name is just legacy from when we only supported RGB/primary
planes. Lets pick a better name now.
Signed-off-by: Rob Clark <robdclark@gmail.com>
We can have various combinations of 64b and 32b address space, ie. 64b
CPU but 32b display and gpu, or 64b CPU and GPU but 32b display. So
best to decouple the device iova's from mmap offset.
Signed-off-by: Rob Clark <robdclark@gmail.com>
If fb dimensions are larger than what can be scanned out, but the src
dimensions are not, the hw can still handle this. So clip.
Signed-off-by: Rob Clark <robdclark@gmail.com>
If the bottom-most layer is not fullscreen, we need to use the BASE
mixer stage for solid fill (ie. MDP5_CTL_BLEND_OP_FLAG_BORDER_OUT). The
blend_setup() code pretty much handled this already, we just had to
figure this out in _atomic_check() and assign the stages appropriately.
Also fix the case where there are zero enabled planes, where we also
need to enable BORDER_OUT.
Signed-off-by: Rob Clark <robdclark@gmail.com>
When CONFIG_PM_SLEEP is disabled, we get a harmless warning
drm/hisilicon/hibmc/hibmc_drm_drv.c:115:12: error: ‘hibmc_pm_resume’ defined but not used [-Werror=unused-function]
drm/hisilicon/hibmc/hibmc_drm_drv.c:97:12: error: ‘hibmc_pm_suspend’ defined but not used [-Werror=unused-function]
Marking the functions as __maybe_unused avoids the warning without
having to add an #ifdef.
Fixes: 5e0df3a08f ("drm/hisilicon/hibmc: Add hisilicon hibmc drm master driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161124163107.3914495-1-arnd@arndb.de
This branch include patches of fixing a typo, accurate dsi frame rate,
and fixing null pointer dereference.
* 'mediatek-drm-fixes-2016-11-24' of https://github.com/ckhu-mediatek/linux.git-tags:
drm/mediatek: fix null pointer dereference
drm/mediatek: fixed the calc method of data rate per lane
drm/mediatek: fix a typo of DISP_OD_CFG to OD_RELAYMODE
Need to be careful to release struct_mutext when request alloc
failed and take consistent handling for return status as with
normal go out path. Ensure to check correct workload request in
complete path too.
v2: Add Fixes note
Fixes: 90d27a1b18 ("drm/i915/gvt: fix deadlock in workload_thread")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Pei Zhang <pei.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
These updates:
* improve the robustness of the driver wrt races
* improve the compliance for sending infoframes and audio
* re-organise the function order in the driver to group like functions
together. (This unfortunately causes a conflict with the change in
drm-misc, but it should be trivial to solve, although it looks more
scarey than it really is - sfr has already sent two reports about
this, one earlier today.)
* simplify tda998x_audio_get_eld and DPMS handling
* power down sections of the chip that we never use
* add some initial preparation for supporting the CEC driver
* 'drm-tda998x-devel' of git://git.armlinux.org.uk/~rmk/linux-arm:
drm/i2c: tda998x: fix spelling mistake
drm/i2c: tda998x: allow sharing of the CEC device accesses
drm/i2c: tda998x: allow interrupt to be shared
drm/i2c: tda998x: power down pre-filter and color conversion
drm/i2c: tda998x: switch to boolean is_on
drm/i2c: tda998x: remove complexity from tda998x_audio_get_eld()
drm/i2c: tda998x: group audio functions together
drm/i2c: tda998x: separate connector initialisation
drm/i2c: tda998x: group connector functions and funcs together
drm/i2c: tda998x: move and rename tda998x_encoder_set_config()
drm/i2c: tda998x: correct function name in comments
drm/i2c: tda998x: only enable audio if supported by sink
drm/i2c: tda998x: only configure infoframes and audio if supported
drm/i2c: tda998x: avoid race when programming audio
drm/i2c: tda998x: avoid racy access to mode clock
drm/i2c: tda998x: avoid race in tda998x_encoder_mode_set()
drm/i2c: tda998x: move audio mutex initialisation
Building on top of the MALI change previously merged, these changes:
* add tracing support for overlay updates
* refactor some of the plane support code
* de-midlayer the driver
* cleanups from other folk reviewing the code
* 'drm-armada-devel' of git://git.armlinux.org.uk/~rmk/linux-arm:
drm/armada: fix NULL pointer comparison warning
drm/armada: use DRM_FB_HELPER_DEFAULT_OPS for fb_ops
drm/armada: remove some dead code
drm/armada: mark symbols static where possible
drm/armada: de-midlayer armada
drm/armada: use common helper for plane base address
drm/armada: move setting primary plane position to armada_drm_primary_set()
drm/armada: split out primary plane update
drm/armada: move plane state to struct armada_plane
drm/armada: clean up armada_drm_plane_work_run()
drm/armada: add tracing support
The probe function requests the interrupt before initializing
the ddp component. Which leads to a null pointer dereference at boot.
Fix this by requesting the interrput after all components got
initialized properly.
Fixes: 119f517362 ("drm/mediatek: Add DRM Driver for Mediatek SoC
MT8173.")
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Change-Id: I57193a7ab554dfb37c35a455900689333adf511c
Tune dsi frame rate by pixel clock, dsi add some extra signal (i.e.
Tlpx, Ths-prepare, Ths-zero, Ths-trail,Ths-exit) when enter and exit LP
mode, those signals will cause h-time larger than normal and reduce FPS.
So need to multiply a coefficient to offset the extra signal's effect.
coefficient = ((htotal*bpp/lane_number)+Tlpx+Ths_prep+Ths_zero+
Ths_trail+Ths_exit)/(htotal*bpp/lane_number)
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
If we want to set the hardware OD to relay mode,
we have to set DISP_OD_CFG register rather than
OD_RELAYMODE; otherwise, the system will access
the wrong address.
Change-Id: Ifb9bb4caa63df906437d48b5d5326b6d04ea332a
Fixes: 7216436420 ("drm/mediatek: set mt8173 dithering function")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
