As the driver is now allowed to probe with a single output endpoint,
power management routines shall now take into account the case a CSI-2 TX
is not enabled.
Unify the adv748x_tx_power() routine to handle transparently TXA and TXB,
and enable the CSI-2 outputs conditionally.
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently the adv748x driver will fail to probe unless both of its
output endpoints (TXA and TXB) are connected.
Make the driver support probing provided that there is at least one
input, and one output connected and protect the clean-up function from
accessing un-initialized fields.
Following patches will fix other uses of un-initialized TXs in the driver,
such as power management functions.
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ADV748x has twelve 256-byte maps that can be accessed via the main
I2C ports. Each map has it own I2C address and acts as a standard slave
device on the I2C bus.
Allow a device tree node to override the default addresses so that
address conflicts with other devices on the same bus may be resolved at
the board description level.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV748x has 12 pages mapped onto I2C addresses.
In the existing implementation only 11 are mapped correctly in the page
enumerations, which causes an off-by-one fault on pages above the
infoframe definition due to a missing 'CBUS' page.
This causes the address for the CEC, SDP, TXA, and TXB to be incorrectly
programmed during the iterations in adv748x_initialise_clients().
Until now this has gone un-noticed due to the fact that following the
creation of the clients - the device is reset and the addresses are
reprogrammed in manually by the call to "adv748x_write_regs(state,
adv748x_set_slave_address);"
As part of moving to dynamic i2c address allocations repair this by
providing the missing CBUS page definition.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current implementation has to search the list of controls for the
pixel rate control, each time it is set. This can be optimised easily
by storing the ctrl pointer in the CSI/TX object, and referencing that
directly.
While at it, fix up a missing blank line also highlighted in review
comments.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Provide support for the ADV7481 and ADV7482.
The driver is modelled with 4 subdevices to allow simultaneous streaming
from the AFE (Analog front end) and HDMI inputs though two CSI TX
entities.
The HDMI entity is linked to the TXA CSI bus, whilst the AFE is linked
to the TXB CSI bus.
The driver is based on a prototype by Koji Matsuoka in the Renesas BSP,
and an earlier rework by Niklas Söderlund.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
